Remington
Experienced athletes share their insights in answering this question:
Introduction Year:
1936
1936
Year Discontinued:
1955
Total Production:
Approximately: 12,200
Designer/Inventor:
C.C. Loomis, A.L. Lowe, K.J. Lowe
Action Type:
Bolt Action – Clip Magazine
Caliber/Gauge:
.22 Long Rifle
Serial Number Blocks:
Starting: 00001Ending: 12300
Grades Offered:
Model 37 Rangemaster37 Target37AR37AF37AX37AM37AV37AS
Variations:
None
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
Where: On rifles, the serial number should be visible above the line of the stock and stamped into the receiver. This may be done on either side of the receiver or on top, at the manufacturer`s discretion.
Remington SERIAL NUMBERS 1921-2012
Remingtons manufactured after 1921 have a code located on the left side of the barrel near the frame that identifies the year and month of manufacture.
The Remington Model 700 is a series of bolt-action centerfire rifles manufactured by Remington Arms since 1962.
Newer model Remington 700 and Model Seven rifles have the “X-Mark Pro” or “XMP” trigger mechanism. Remington has issued a voluntary recall of XMP triggers, which were manufactured from 2006 to 2014.
Serial Number Information
Under current federal law serial numbers must be located on the frame or receiver of every firearm. Serial numbers (or partial numbers) can also be located on many other parts of firearms as well.
A. The Federal Gun Control Act of 1968 requires that serial numbers be stamped on all firearms manufactured for sale in the United States since 1968. (1) A factory-assembled pistol normally will have a serial number.
The Remington company was founded in 1816.
308 comprised total production of only 142 with a Mannlicher-style stock. But the rarest Original Model 600 was and remains the . 223.
THE MODEL 700® A LEGEND FORGED IN STEEL. 60 YEARS OF UNRIVALED PERFORMANCE. It`s the number one bolt-action of all time, proudly made in the U.S.A. Since 1962, more Model 700s have been sold than any other bolt-action rifle before or since.
Remington has sold its businesses in parts amid the 2020 bankruptcy. Therefore, the Remington brand and assets will now be owned by different companies including Ruger, Vista, Roundhill Group, Sierra Bullets, JJE Capital Holdings, and Franklin Armory.
If you possess ammunition from these lot codes, immediately discontinue use of this ammunition and contact Remington at 1-800-243-9700. Remington Ammunition Consumer Service Department will arrange for the return shipment of your ammunition and upon receipt will send you replacement ammunition at no cost to you.
But like just about everyone else in Ilion, N.Y, a small town in New York`s Herkimer County about 80 miles northwest of Albany, Seymour has a soft spot for Remington Arms, the gun manufacturer that has been located here since Eliphalet Remington started making firearms in 1816.
Barrel stamp – A stamp pressed into the side of the barrel of a firearm that typically states the manufacturer, the gauge or caliber, and the chamber size.
An 80% lower is, by the ATF`s definition, not a firearm in most states. Therefore, you are not required to serialize or register a rifle built using an 80% lower or blank receiver.
ATF has noted cases where some licensed importers have adopted the same serial number for more than one firearm. These instances of duplication have generally occurred when firearms are received from more than one source.
A rifle scope specification includes two numbers. The first number identifies the magnification while the second number identifies the diameter of the objective lens.
If the firearm has no serial number, and never had a serial number, the lack of a serial number renders the firearm illegal. [Except a non-NFA home manufacture that you have no intent to sell, which we will explain later.]
Model numbers or names are often stamped or engraved on the barrel or slide, often along with the Make. In some cases, the Model will also be represented as a prefix or other portion of the pistol`s serial number, or may be stamped on the frame in less obvious locations (e.g., under the grip panels).
Find the rifle`s serial number where the barrel meets the receiver. SEE GRAPHIC A For a right-handed rifle, the serial number is located on a user`s left. For a left-handed rifle, the serial number is located on a user`s right.
The Model 514 was introduced in 1948 and was discontinued in 1970, while the Model 25N is a much newer 22-caliber rifle that was introduced in 1989, and was later renamed the Model 925. Remington acquired the Marlin operation in 2007 and continues to manufacture various models of 22-caliber rifles.
Remington Model 700 Serial Number Lookup: Remington Firearms manufactured after 1921 have a code located on the left side of the barrel near the frame that identifies the year and month of manufacture.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have just purchased the S&W Model 10 with Serial Number 3002350. Should the number on the cylinder arm match the serial number on the butte?
ANSWER : Yes they should. However
This thread says the number on the frame is model designation.
http://www.longislandfirearms.com/forum/topic/50850-smith-and-wesson-model-10-date-of-manufacture/
http://www.smithandwessonforums.com/forum/s-w-revolvers-1945-present/18463-s-w-model-10-maybe-early-1950s.html
Lots of info here on variations
http://www.northeastshooters.com/vbulletin/threads/68254-How-to-Identify-Date-a-S-amp-W
These people will date it for you.
http://smith-wessonforum.com/s-w-revolvers-1961-1980/125114-model-10-serial-numbers.html
Read Full Q/A … : Remington
I have a Winchester Model 190 with serial number B1302781. This model and serial nubmer does not show up on the Windhester site. Can you tell me when this rifle was manufactured?
ANSWER : The model 290 came out first, in 1965. The 190 came out in 1967. The 290 was made until 1973 and production of the 190 ended in 1980. There were approx. 2,150,000 model 190/290 made through the years.Since yours was made before the middle of the production run, and before 1973, I would guess late 60’s to around 1970 or 1971.
Hope this helps.
Read Full Q/A … : Remington
Winchester model 100 semi-auto 308 cal. how to disassemble?
ANSWER : IMPORTANT Recall info:
WINCHESTER MODEL 100 FIRING PIN RECALL – A notice dated 7-1990 relates the following
“PRODUCT SAFETY WARNING AND REPLACEMENT NOTICE. Attention owners of Winchester model 100
rifles and carbines please read this notice. In July of 1990 the following product safety
warning was issued by Winchester. It has come to our attention that the firing pin in the
Winchester Model 100 Rifle or Carbine may break due to use and metal fatigue and become
lodged in the breech bolt face. If this occurs, the firearm may fire before the action is
locked causing severe damage to the firearm and possibly injury or death to the shooter
and bystander.
WARNING DO NOT SHOOT YOUR WINCHESTER MODEL 100 RIFLE OR CARBINE. Repair and replacement.
A new firing pin has been designed to replace the firing pin originally made for the
Winchester Model 100 Rifle and Carbine. The new firing pins will be available in April
1991. If you own a Winchester Model 100 Rifle or Carbine, please send your firearm to one
of the authorized Winchester Model 100 Firing Pin Replacement Centers indicated below.
Your Winchester Model 100 firearm will be inspected, the firing pin replaced and tested
and the firearm returned to you. The inspection, replacement/testing and return postage
will be accomplished at no cost to you. If other repair or maintenance work is authorized
by you to be performed on the firearm when the firing pin is replaced, such work shall be
at your cost.”
W. R. Long Gunsmiths 2007 Brook Road North Cobourg, Ontario K9A4W4Canada Frank LeFever & Sons RD 2 Box 31Lee Center, NY 13363USA Bolsa Gunsmithing7404 Bolsa AvenueWestminister, CA 92683USA Nu Line Guns1053 Caulks Hill RoadHarvester, MO 63303USA
If you have any questions concerning this notice, call Winchester Product Service
1-800-852-5734 or write to Winchester Firing Pin replacement Notice, PO Box 10 Cottage
Hills Illinois 62018 Attention Product Service Dept.
———————————————————————————-
The following is Wisner’s rendition & info on the subject.
The difference in the old firing pin and the new one is as follows. The old replaced
style, was totally lathe tuned (round). While the new recall style is similar in lathe
turning on the front and back, but in the front midsection it has two flats milled, one
on each side. This makes the center section stronger. Also replaced is the bolt sleeve
lock pin (firing pin guide) which was made to accommodate this different shaped firing
pin
Part number for the new parts are, firing pin =1391ND, bolt sleeve locking pin =1491ND
The word was at the time this recall was in process was that if the firing pin would
break at the mid section and still remain in the gun as two pieces, the possibility of a
premature discharge before the bolt was locked was possible. This apparently was caused
by the firing pin tip (now not having a retracting spring) to be stuck forward, and
thereby slam-firing upon chambering.
The responsibility for the recall apparently was on Olin, as they were the parent company
at time of manufacture. Olin set up regional recall centers at three established US
gunshops. There was a manufacturing delay in the replacement firing pins, and a backlog
occurred, also some collectors did not like the idea of shipping their guns long
distances. Olin then also authorized other gunshops to make the required alterations.
Upon completion of the recall, the shops were to test fire the firearm and to stamp an
assigned letter on the inside top of the receiver as seen thru the magazine well with the
bolt retracted. The letter “B” represented Bolsa Gunsmithing, “L” was Lefever, and “N”
was for Nu-line Guns. The letter “X” apparently was for all the other independent shops.
However this identification information did not get communicated to some of the smaller
shops at the start of the project. The only way to tell if the gun as been modified, if
the ”letter” is not present, is to take the barrel & action out of the stock, remove the
trigger guard assembly and the try to rotate the firing pin by twisting it. If it does
NOT rotate, then the firing pin recall HAS been performed.
For link back to the parts & price list that we make & have for sale CLICK HERE
Copyright © 2004-2007 Wisner’s Inc. All Rights Reserved
Back to Additional information To Winchester model 88 & 100 parts
Originated 01-13-2001 Last Modified 03-19-2007LeeRoy Wisner
WINCHESTER MODEL 100 FIRING PIN RECALL – A notice dated 7-1990 relates the following
“PRODUCT SAFETY WARNING AND REPLACEMENT NOTICE. Attention owners of Winchester model 100
rifles and carbines please read this notice. In July of 1990 the following product safety
warning was issued by Winchester. It has come to our attention that the firing pin in the
Winchester Model 100 Rifle or Carbine may break due to use and metal fatigue and become
lodged in the breech bolt face. If this occurs, the firearm may fire before the action is
locked causing severe damage to the firearm and possibly injury or death to the shooter
and bystander.
WARNING DO NOT SHOOT YOUR WINCHESTER MODEL 100 RIFLE OR CARBINE. Repair and replacement.
A new firing pin has been designed to replace the firing pin originally made for the
Winchester Model 100 Rifle and Carbine. The new firing pins will be available in April
1991. If you own a Winchester Model 100 Rifle or Carbine, please send your firearm to one
of the authorized Winchester Model 100 Firing Pin Replacement Centers indicated below.
Your Winchester Model 100 firearm will be inspected, the firing pin replaced and tested
and the firearm returned to you. The inspection, replacement/testing and return postage
will be accomplished at no cost to you. If other repair or maintenance work is authorized
by you to be performed on the firearm when the firing pin is replaced, such work shall be
at your cost.”
W. R. Long Gunsmiths 2007 Brook Road North Cobourg, Ontario K9A4W4Canada Frank LeFever & Sons RD 2 Box 31Lee Center, NY 13363USA Bolsa Gunsmithing7404 Bolsa AvenueWestminister, CA 92683USA Nu Line Guns1053 Caulks Hill RoadHarvester, MO 63303USA
If you have any questions concerning this notice, call Winchester Product Service
1-800-852-5734 or write to Winchester Firing Pin replacement Notice, PO Box 10 Cottage
Hills Illinois 62018 Attention Product Service Dept.
———————————————————————————-
The following is Wisner’s rendition & info on the subject.
The difference in the old firing pin and the new one is as follows. The old replaced
style, was totally lathe tuned (round). While the new recall style is similar in lathe
turning on the front and back, but in the front midsection it has two flats milled, one
on each side. This makes the center section stronger. Also replaced is the bolt sleeve
lock pin (firing pin guide) which was made to accommodate this different shaped firing
pin
Part number for the new parts are, firing pin =1391ND, bolt sleeve locking pin =1491ND
The word was at the time this recall was in process was that if the firing pin would
break at the mid section and still remain in the gun as two pieces, the possibility of a
premature discharge before the bolt was locked was possible. This apparently was caused
by the firing pin tip (now not having a retracting spring) to be stuck forward, and
thereby slam-firing upon chambering.
The responsibility for the recall apparently was on Olin, as they were the parent company
at time of manufacture. Olin set up regional recall centers at three established US
gunshops. There was a manufacturing delay in the replacement firing pins, and a backlog
occurred, also some collectors did not like the idea of shipping their guns long
distances. Olin then also authorized other gunshops to make the required alterations.
Upon completion of the recall, the shops were to test fire the firearm and to stamp an
assigned letter on the inside top of the receiver as seen thru the magazine well with the
bolt retracted. The letter “B” represented Bolsa Gunsmithing, “L” was Lefever, and “N”
was for Nu-line Guns. The letter “X” apparently was for all the other independent shops.
However this identification information did not get communicated to some of the smaller
shops at the start of the project. The only way to tell if the gun as been modified, if
the ”letter” is not present, is to take the barrel & action out of the stock, remove the
trigger guard assembly and the try to rotate the firing pin by twisting it. If it does
NOT rotate, then the firing pin recall HAS been performed.
For link back to the parts & price list that we make & have for sale CLICK HERE
Copyright © 2004-2007 Wisner’s Inc. All Rights Reserved
Back to Additional information To Winchester model 88 & 100 parts
Originated 01-13-2001 Last Modified 03-19-2007LeeRoy Wisner
Read Full Q/A … : Remington
I have a Eddystone (Remington) 1917 rifle with serial # 1183417…I was wondering if you could tell me when it was exactly..?
ANSWER : Military Dates of Manufacture This link will take you to the general web page, select your Eddystone M1917 rifle and enter the number. It says yours was made in November of 1918. The U.S. Army discontinued the use of the M1917 in 1919 after they voted to keep the M1903 as the main service rife due to poor performance in shooting contests. Have fun with that awesome piece of American History and treat her well.
Read Full Q/A … : Remington
Hi i was wondering if i could get an estimated value of this winchester rifle. it is an 1886 model 33 cal rifle serial number 139297 and was a special order gun made in 1906. according to the Winchester museum in Wyoming there was only 3 made. Any help would be great thanks.
ANSWER : Take a look at http://www.gunsinternational.com/Winchester-Model-1886-Rifles.cfm?cat_id=501&start_row=51
and other sites and you can just about make your own estimate
Read Full Q/A … : Remington
On my model 770 in 300 mag. new right out of the box, cleaned in and oiled it but the bolt action was still sticky and after firing a box and a half though it it still will not eject the spent casing and I have to turn the gun on it’s side and let it drop out on it’s own. I have even called Remington’s repair shop in Or. and they can’t guarantee it will work as he said it was nothing but a cheap rifle from Remington. I will be sending to Remington’s repair shop and if they can not repair it what rights do I have to get my money back? As I don’t feel that I should keep on having to pay for shipping all the time for there poorly made rifle.
ANSWER : I am not sure what u are asking here if anything??
Read Full Q/A … : Remington
Looking for the age of a Remmington model 121
ANSWER : Cant give you an Exact but I can give you the Manufacture Years:Manufactured from 1936-1954
Read Full Q/A … : Remington
