ull the lever again.
A 5 Standard Paintball Gun

Experienced athletes share their insights in answering this question:
Couple of things.. the A5 is a wonderful marker, got a couple myself.Make sure it’s clean in there. You probably can’t see under the bottom of the feeder into the mechanism. If paint gunk and dirt get in there, then it may not be able to turn.If it’s beyond that, there’s a cog in there that is key to turning the feed mechanism and can break. But if you can cycle it by hand then that may not be your problem.Is it only later on when you’re playing? Pressure is important here because not only are you propelling the ball out the marker, and working the internals, you are also pushing the feed mechanism for each shot and if there’s not enough pressure you won’t get that auto-feed.Try a full tank and see if it works better. Try a different tank than you’re currently using. Try nitrogen/compressed air if you’re using co2. Variations of a theme here if you couldn’t tell.Good luck.. if that doesn’t identify your problem, a quick trip to your local Tippmann certified airsmith should get it back into shape in short order. Play hard, play safe, play with honor! 8^)

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Automatic paintball guns do not require the player to press the trigger continuously to release paintball rounds. Players can hold down the trigger to release continuous rounds. These types of guns are perfect for players looking to increase their rate of fire in the field and take part in tournaments.
Simply, high-pressure air regulators control the pressure in your paintball gun from the air source, usually an air tank, to ensure projectiles are launched correctly. An air tank will have its own PSI rating, and regulators will lower these to a more suitable level for your model, usually between 450 and 850 PSI.
PSP mode is an enhanced (ramping) mode, that allows your marker to fire quicker than you are actually pulling the trigger. The marker will shoot in semi auto until the enhanced mode is activated, which occurs when certain conditions are met.
Believe it or not, paintball is a sport, and, just like rugby, lacrosse or even football, you may end up with a bruise or two. But bruises from paintball are completely normal and often feel like a light sting when being shot.
A gravity-fed paintball hopper is precisely what it sounds like: a basic paintball hopper attached to the feed neck of a paintball gun that feeds paintballs into it by allowing them to drop into the gun`s breech simply by gravity.
Both Co2 and Compressed Air tanks are made out of aluminum and are most often black in color. However, only Compressed Air tanks are wrapped in Carbon Fiber. If your tank is Carbon Fiber wrapped then you have a Compressed Air tank.
In most cases, paintball guns use compressed air tanks with high pressure ratings, generally ranging from 3000 psi up to 5000 psi. The paintball guns balance the pressure using a regulator connected to the piping to achieve the ideal output.
Which hurts more? As there is a considerable difference in the sizes of ammunition Airsoft strikes hurt less than Paintball hits. Due to the higher impact rate of paintballs, you will often see professional paintballer wear lightweight armour similar to motorcross armour and always sporting full-face protection.
In paintball participants try to hit each other with paintballs launched from a special paintball marker/gun. While airsoft is cheaper and provides a more realistic warfare experience, paintball is more popular, more organized and has larger events.
Most people state that paintball doesn`t hurt too much; it usually feels like a firm flick. But this will depend on how fast the ball is going, the distance it travels and where on the body it hits you. Paintball injuries won`t be too extensive, but you should expect a few minor bruises and bumps after paintballing.
But even though airsoft pellets reach a speed of almost double paintballs, in general, paintballs will hurt more. This is because they`re much larger, which means they carry more energy when they`re hurtling towards someone!
The explosive gas from the cartridge drives the bullet down the barrel. At the same time, the gas pressure pushes in the opposite direction, forcing the bolt backward. As in the recoil system, an extractor pulls the shell out of the barrel, and the ejector forces it out of the gun.
Reasons to Play Pump:

Save on paint and money on equipment. Would like low maintenance and simple equipment. Prefer a lightweight marker and tank for woodsball. Don`t need to shoot rapid fire.

The explosive gas from the cartridge drives the bullet down the barrel. At the same time, the gas pressure pushes in the opposite direction, forcing the bolt backward. As in the recoil system, an extractor pulls the shell out of the barrel, and the ejector forces it out of the gun.
Paintball Tank Types

Most modern electronic or mechanical markers run on compressed air; cheaper or older-style mechanical markers can often run on either Co2 or compressed air*. Pistols normally run on pre-filled disposable co2 cartridges.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Read Full Q/A … : A 5 Standard Paintball Gun

APA 8 BALL POOL LEAGUE RULE QUESTION. ….IF 8 BALL IS SITTING ON VERY EDGE OF LEFT HAND CORNER POCKET…. THE OTHER OPPONENT SHOOTS THE 4 BALL TO THE RIGHT HAND CORNER POCKET & WHEN THE 4 BALL DROPS INTO THE RIGHT HAND POCKET THE VIBRATION FROM THE 4 BALL DROPPING CAUSED THE 8 BALL TO DROP IN THE LEFT HAND CORNER POCKET….WHAT WOULD BE THE RULING ON THIS?
ANSWER : It is an illegal shot and the player who made the 4 ball shot loses the game

Read Full Q/A … : A 5 Standard Paintball Gun

I have a wildwood le 25bhbs and the only towing lights working are my signal lights. can’t get running lights or brake lights to work. I saw where it looked like the towing harness may have been pinched. So I repaired that, but, they still do not work. Any ideas? Is there a fuse somewhere I need to check? Do I need to hook the trailer up to my trailer hitch before they will work? Is there a wiring diagram or repair manual somewhere I can get? Any help would be greatly appreciated. Thank you.
ANSWER : There should be an inline fuse, check that first.

Read Full Q/A … : A 5 Standard Paintball Gun

I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.

Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.

Read Full Q/A … : A 5 Standard Paintball Gun

How do I fill a soccer ball with helium? Do I need a special adapter? I have a ball needle. My son is comparing a soccer ball with air, one with nitrogen and (hopefully) one with helium for a science project.
ANSWER : It would take a frankenstein of conectors to go from a gas bottle to a soccer ball. i would get a ball needle and have it soldered to a gas hose fitting. any welding supply store would have the gases and fittings you would need and would probably be willing to help if you tell them what its for

Read Full Q/A … : A 5 Standard Paintball Gun

I just bought a new tippmann 98 custom act platinum edition and it doesnt seem to be firing right. i upgrades the rear bolt and trigger and after a few shots the bolt lock in the firing position. if i pull the trigger forward there is a click and then it will fire, but imediatly lock up again
ANSWER : I would look in to the bolt and check that it moves freely, also check that is properly lubed, and finally that your upgrade bolt does not need a different spring. I would also check the batteries on the grip if it is an E-trigger.

Read Full Q/A … : A 5 Standard Paintball Gun

Machine will stop adjusting resistance. On start up the machine will usually work. I can go through the calibration procedure and it will calibrate and work normally for 4 or 5 resistance adjustments. It will then stop adjusting. It acts like there is a cable pulled and refuses to adjust, even though I am not getting the warning telling me to “Release cable”
I have modified the wiring harness so that the wires do not fall off from the stepper motor, so this is not the problem. If I shut the machine down and leave it for several minutes, it will come back and work normal again… for a while. I am wondering if there is a problem with the sensors that are detecting a cable pull? Is there a way to disable those sensors to see if that is the problem
ANSWER : I would think that your problem has possibly to do with a faulty power supply, component, see to my mind it is a thermal problem as it heats up,it goes faulty? The Voltage changes and it goes out of spec.. When left to cool, it then is OK… Usually, & from my experience this is a thermal problem. To see obtain some Freeze Spray, from radio Shack or similar,and spray components on the main power board, and others too, use it on any large heat sinked components and see if when you do this the fault clears. Then replace that component(s).

Or as you suggest the sensors that feed the inputs maybe with sensors though one has little option but to replace them and see if this clears the problem.

Read Full Q/A … : A 5 Standard Paintball Gun