ow what goes to what.
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
HI.Were the switch going to the terminal of the battery?

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

A 6 Pin Push Switch also known as Mini DPDT Push Switch, is nothing but a combination of two push switches placed together inside one package. Unlike momentary switches which connect the wires of the switch only for a second, this switch retains its ON-OFF state till pushed later on.
Power buttons and switches are usually labeled with “I” and “O” symbols. The “I” represents power on, and the “O” represents power off. This designation will sometimes be I/O or the “I” and “O” characters on top of each other as a single character, as in this photo.
An electric switch is a device that interrupts the electron flow in a circuit. Switches are primarily binary devices: either fully on or off and light switches have a simple design. When the switch is turned off, the circuit breaks and the power flow is interrupted. Circuits consist of a source of power and load.
The most common household switch, a single-pole, has two terminals and simply turns power on or off. A three-way switch has three terminals; a four-way has four.
A DPDT switch has six terminals.
A three-way switch does not have markings on it since there`s no true ON or OFF position. There are three screw terminals on the body of the switch, in addition to the green grounding screw.
A common style of a switch is a rocker design, which includes on/off markings.
A Double Pole (or DP) switch is a switch that controls two circuits at the same time. In terms of residential switching, this normally means it switches the live and neutral at the same time.
There are various types of main switches, namely load-break switches, circuit breakers, load switches, disconnectors and pure emergency stop switches. Load-break switches, also called repair switches or emergency stop switches, combine several of these functions. They are at once a load switch and a disconnector.
4-way switches have four terminals on them: two for traveller wires coming in, and two for traveller wires going out.
well simply put the terminal is the component. used to connect the circuit to the switch to enable it to function correctly. the terminals of a switch conduct electricity to and from the switch`s. contact point the termination of a switch all depends on the final.
The JJ Guitars 6 way switch, developed in conjunction with Free-Way, offers a dedicated series & parallel function for guitars equipped with twin Humbucking pickups. The JJ Edition has 9 terminal connections.
A six-wire motor uses three individual sets of coils which can be wired for either high- or low-voltage. Since there are essentially three coils acting as resistors, they may be connected in series for high voltages in order to decrease the current.
Because they`re carrying two transmission lines. In US terminology, this would be called a “double circuit” structure. >tower.
6 AWG wire is on the larger end of the spectrum in terms of common use, and is appropriate for roughly 55 amps and an absolute maximum of 60 amps. The heavier the gauge, the higher the amps that are appropriate for the wire in question.
The button toggles between two states (sound on/off) and changes the icon accordingly. The switch does more or less the same thing (left off/right on).
1 Way Switches: If a light switch is `1 way` this means it is just an on/off switch. This is the simplest type of switch that you can get. The single switch controls a single light (or lighting circuit). 2 Way Switches: A `2 way` switch means there is another switch controlling the same light.
A switch can only exist in one of two states: open or closed. In the off state, a switch looks like an open gap in the circuit. This, in effect, looks like an open circuit, preventing current from flowing. In the on state, a switch acts just like a piece of perfectly-conducting wire.
The easiest way to determine whether a circuit is 15 or 20 amps is to look at the corresponding breaker or fuse in the breaker panel. Dedicated circuits are electrical lines that carry an electrical current to one single outlet.
It comes from the binary system (“1” means “on”). ⭘ (HEAVY CIRCLE), the power off symbol. It comes from the binary system (“0” means “off”). The power off (circle) symbol or “O” on a button or toggle, indicates that using that control will disconnect power to the device.
Some of the most common light switch types are single-pole switches, double-pole switches, and three-way switches.
As a rule, we must always install 3-way switches in pairs, and then as many 4-way switches as necessary. For example, if a light is to be controlled from four different locations we would need two 3-way switches and two 4-way switches.
4-Way Switches

Four-way switches are used to control lighting from three or more locations. Four-way switches are used in combination with 3-way switches. There are four terminals that provide two sets of toggle positions on a 4-way switch. Each set of terminals is one of the toggle positions.

Three pole or three-way switches are used to control one or more lights or fixtures from multiple locations, such as the top and bottom of a flight of stairs. Single pole and 3-way switches look the same when installed but are used for different purposes.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Read Full Q/A … : Sport & Outdoor – Others

Hello, I have an old Tippman A5 (about 5-6 years
ANSWER : You will have to buy a different barrel for the A5, I would suggest ansgear.com, rockstartactical.com, or ebay. Make sure that you get the right threads along with an apex capeable front. I would suggest the sly carbon fibur barrels, or get a autococker barrel and a lapco adapter for your A5. Hope this helps if you have any questions just let me know.

Read Full Q/A … : Sport & Outdoor – Others

I have a Kohler Condidant 5 Generator that will run as long as you hold the start button in. It dies when you let off. I have a harness for the remote switch but no switch – It also will start the generator when you cross the red and black wire and run as long as you hold them together. There are 3 wires to the main switch and 5 to the remote switch. Does the starter stay engaged the whole time you hold the start switch or does the computer release the starter once it is running? The Generator is producing electricity because I tested it while holding the start button. Some where is a wire that shold tell it to keep running. I have read online many descriptions of the same problem, most are told the board is bad so they replace it and still have the problem. Have not found a solution. Talked to a marine machanic today and he said he fixed his friends generator doing the same thing by running a bypass wire but he couldnt remember exactly what he did it was a long time ago. Can anyone help me. Thank you
ANSWER : The problem is either the ballast resistor or the starter bypass relay. The bypass relay should be part of the starter solenoid. I’m afraid I can’t tell you exactly where the ballast resistor is located. It should be a physically fairly large resistor made of ceramic. It should be retangular roughly 1.5″-3″ long and 3/8″-1/2″ accross with a wire on each end. It could also be a coil of wire mounted on a phenolic board.
If you need more help just add a comment and I’ll respond as soon as I get the message.

Read Full Q/A … : Sport & Outdoor – Others

3 year old Toro Z4200 time cutter Z, 19 HP Kohler, engine runs great, new battery, new solenoid, with the seat sensor connected or by-passed, STILL WONT start off the key switch. Clicks at the kill relay. Would the kill relay be the problem?
Whats confusing is, both the green and blue posts on the solenoid have 14.01 volts when you turn the key to ‘start’ position. Did the same thing with the old solenoid, which is probably still good. I replaced it to eliminate that variable. It also ‘clicks’ at the fuel switch at the carburetor bowl, but that is only 1 lead (I assume a hot lead) so Im thinking that CANT be it.
Using the old hillybilly method, jumping across the 2 top posts on the solenoid, with the key in on position, it will start right up, run, drive and mow just fine.
So my best guess is this ‘KILL RELAY’ must be bad?
Any help would be appreciated, thank you !
ANSWER : These things are pre requisites for engine cranking: PTO/Blades are off/button pushed down, the steering arms are out/parked position, and you are in the seat. I think. Definitely the blades have to off.

Read Full Q/A … : Sport & Outdoor – Others

Spark plug wire boot grounding out on coil, 96 outback 2.5 automatic, just put new spark plug wires, new spark plugs, and new coil on. ran great for two weeks, now spark is jumping out of boot at coil on one wire, put old coil back on and still does it in the same spot. replaced wires again, and still does it in the same spot. seems to do it only under a load. Is my new spark plug on that cylinder bad? Does the coil need some insulation under it? It is the coil that sits right on top of the motor. Any ideas? thanks.
ANSWER : Sparks are high voltage, and will always follow the path of least resistance. If you can visibly see a spark (whether in a lighted area, or in the dark), that means either that a plug wire (or coil wire) is open (non conductive), or your have a carbon track on the surface where the spark can be seen, but most likely you have BOTH problems!

If you have an ohmmeter, check the resistance of each wire involved, particularly spark plug wires … which means you must be able to connect to both ends of each wire at the same, and hopefully, FLEX those wires, to be sure they don’t have a break inside that is intermittent (comes and goes)!

Read Full Q/A … : Sport & Outdoor – Others

I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.

Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

Bike pedal is striped , get a new one or buy new bike?
ANSWER : It depends on the bike. if it’s a “cheap-o” bike;
if it’s one for little kids that costs under $50 – $70 or so then yeah, just get a new one.
if it’s a nice bike that cost you a bit more, i’d get it repaired at a bike shop or a sporting goods store.

Hope this helps!

Read Full Q/A … : Sport & Outdoor – Others