nti-reverse doesn’t work correctly. Can’t figure out how to fit spring on to RD 9208 ‘anti-reverse cam’ and interact it into RD 6887 ‘Roller clutch assembly’. I have the schematic assembly but no details of how to interact these parts so anti reverse works correctly. Help! Thanks.
Jim Davidson
Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

The anti-reverse mechanism is usually internal to the bearing on the handle of the reel. If they get dirty or dry or both the anti-reverse will not work consistently. Clean it and grease it and you should be good to go.
The Sahara FJ features a screw-in handle and an anti-reverse switch, providing anglers with dependable performance while pursuing their next trophy catch.
ANTI-REVERSE SWITCH

This feature is typically located at the bottom of the reel and can be a helpful tool when fighting fish. This switch allows you to backreel, or reel in reverse, rather than relying on your drag system for line tension.

An instant anti-reverse prevents the rotor from moving backwards instantaneously insuring solid hooksets. Instant anti-reverses use a roller bearing for immediate engagement unlike a multi stop which relies on a series of teeth. The gaps between the teeth of a multi stop result in back play thus delaying hooksets.
A typical infinite anti-reverse bearing (roller clutch bearing) uses springs that compress and allow the rollers to move freely in the normal direction. The springs also align and help position the rollers so they will lock into the tapered edges on its cage (retainer), if rotated in the reverse direction.
Contrary to common belief, Shimano reels are not made in the USA but in Japan. Here, at the company`s headquarters in the city of Sakai, all of Shimano`s high-end, premium reels are manufactured and shipped out to the world.
Reel lubricants

Because WD-40 is a degreaser, it breaks down grease and oil. Never use it to lubricate a reel. The basic rule of thumb is to grease gears and oil everything else — sparingly. Too much grease and oil impede the spool and reduce casting distance.

Cleaning solvents

Isopropyl rubbing alcohol will do if a reel needs only minor cleaning, said Dan Thornburn, a Shimano reel guru who does reel maintenance clinics at sports shows. He applies the alcohol with a pump spray bottle. “For heavy cleaning, I use Crystal Simple Green cleaner,” Thornburn said.

Most all fishing reels made to be used with spinning rods will allow you to switch the reel handle side. Just follow a few steps to switch your reel handle from the left side (for right-handed casters) to the right side (for left-handed casters).
Backlashes occur when your lure slows down during or after a cast, but the spool keeps spinning, which results in a tangled mess of line. Today`s baitcasters feature sophisticated braking systems and anti-backlash mechanisms that make it easier for anyone to cast without experiencing line overruns.
Incororating the Propulsion Line Management system for longer casts and reduced backlash, the Sienna FE series of lightweight yet tough spin reels uses Super Stopper II for instant anti-reverse with no backplay.
Run the line through the guides on the rod to the reel with the bail open and tie it tightly to the spool. If you use a regular overhand square knot, pass the end through twice instead of just once – it will help keep the line tight on the spool.
The back bearing may be calculated by adding or subtracting 180° from the forward bearing. The result must fall between 0° and 360°, so if the forward bearing is less than 180°, add 180° to it, or if it`s greater than 180°, subtract 180°.
The back bearing may be calculated by adding or subtracting 180° from the forward bearing. The result must fall between 0° and 360°, so if the forward bearing is less than 180°, add 180° to it, or if it`s greater than 180°, subtract 180°.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Cannot open Shakespeare Synergy Steele 2001s fishing reel
ANSWER : Alright man……i had the same problem. it just takes a little bit of elbow grease, bot it does twist open, it’s just harder than hell to get it to twist off. I took a towel and laid it over the reel, and lightly tapped on it with a hammer to loosen it up a bit.

Read Full Q/A … : Sport & Outdoor – Others

Penn Spin Reel will not lock after casting
ANSWER : On the front of the spool there is a device to turn to set the drag. Torn it tighter and tighten it until slightly below the breaking point of your fishing line. It isn’t a critical adjustment, it just keeps your line from breaking while trying to land a fish.

Read Full Q/A … : Sport & Outdoor – Others

Gas not coming through lines on patio heater
ANSWER : Change the turn on swich it has bad connection due to moisture and rust inside it,if my info was of any help to you please leave a comment,thank you

Read Full Q/A … : Sport & Outdoor – Others

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Read Full Q/A … : Sport & Outdoor – Others

I have a mitchell riptide 80 spinning reel. I lost the screws and parts that hold the bail to the reel. I need a manual to show me the parts that I need to get. I also need the manual to show me exploded views so that I can clean and do maintainance on it.
ANSWER : Hello LVAmtrak,

Here is a link to the schematic and a site where you can purchase parts if necessary.

http://www.mikesreelrepair.com/schematics/displayimage.php?album=15&pos=270

Hope this helps.

Thanks,

Pat

Read Full Q/A … : Sport & Outdoor – Others

A ryobi 780r trimmer developed strong vibration. The crankshaft was spun on the bearing. Wear mark on crankshaft. I replaced short block assembly (incl head,bottom case, case bearing,piston, crank and spark plug pre-assembled), clutch drum assy, spacer and clutch cover assy. Trimmer started easily before. Now can get to cough only, cannot run. Only part I’m unsure of is spacer. I installed with groove toward flywheel. Carb and hoses were not disassembled. Can’t figure it out. Help! thanks, Will
ANSWER : Hi, reset the flywheel gap to 8 thou. Also check the flywheel is located correctly on the crankshaft as your symptoms indicate a timing problem. Hope this helps, regards Phil.

Read Full Q/A … : Sport & Outdoor – Others

How to I fix a spin casting reel?
ANSWER : You should be able to remove the spool by removing the knob on the front of the reel which also is the drag adjustment. With the knob off the spool should pull right off. Hope this helps you

Read Full Q/A … : Sport & Outdoor – Others