Own a 7888 motorised treadmill.Moved it from one room to other, now E3 keeps coming up when i turn it on. Don’t have book for it.

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?

When i go to stari my bike it doesnt turn over i

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.

Humminbird fishfinder 525 will not come on. It is getting power to the base other than that will not come on. Before it did that it showed loading and could not get it to turn off so i had to unplug it now it will not come on what can i do

2011 ninja 1000 fuel pump not coming on
first cycle of the key, but injectors come on.

Engine killed when i hit a bump and let out clutch.
I restarted it and let out clutch and it killed again.
I parked the bike on the stand and let it sit for an hour, then i restarted it and the bike started up, when i gave it gas it backed fire.
Do you think it could be the fuel pump or relay? The shop thinks it could be the kick stand switch, but even acts up on neutral and the gas pump doesn’t come on first cycle of key when cold. Only injectors come on.

Kawasaki bayou 1992, i changed the starter it turns but does not engage, the chain turns the gear moves but moter turns doesnt turn over.. what am i overlooking, ive tried what i know and nothing works..

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.