Coleman
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
The problem of an appliance not lighting is usually caused by one of two things. Either the generator is clogged-up with soot, or the fuel & air tube is blocked by dirt or varnish. Lanterns. (go to stoves) Give it 30 or 40 pumps to really pressurize it well.
If the lantern is not turning on, it may be due to a broken switch issue and not the bulb itself. To check if the switch is broken, make sure the lantern charges fully and that charging light indicates it is charging. Also, check to make sure the current lightbulbs are not broken and defective.
Lanterns and stoves made from about 1951 to present are usually stamped on the bottom of the fount. You will see two sets of numbers; the number on the left is the month and the one on the right is the year of manufacture.
The most common reason a gas stove won`t light is that the igniter is clogged with debris. Over time, dirt and dust can accumulate on the igniter and prevent it from sparking. If this is the case, you`ll need to clean it off in order for the stove to work properly.
This is the most common reason for pressure loss and is usually caused by a deformed or dry rotted gasket in the cap. To fix it just replace it, if you can. Keep the original for display but use a new replacement cap for use.
Coleman Propane Lantern
propane cylinder will power the lantern for up to 4.3 hours on high and 9.25 hours on low.
They are all good. They are much better than the originals and will last you the rest of your life. I exclusively cook on Coleman stoves, and my standard thing is to get a new stove, clean out the fuel tank, replace the pump leather and cap gasket, and just use. Occasionally, the stoves need a new generator.
Beyond replacing damaged mantles, American Gas Lamp Works recommends that you replace your mantles at least once per year. Changing your mantles annually will ensure that your lamp remains bright and fuel-efficient.
Light a match or lighter and hold it below the mantle(s). Open the valve one-quarter turn and wait for the mantle(s) to ignite. 12. Once the mantle(s) start to burn steady (but dim) open the valve all the way and pump more air into the fount for maximum brightness.
Your gas hob might not ignite properly if spilled food or dirt is clogging the ignition nozzles. Ignition may also fail if the nozzles, burner caps or ports are wet after cleaning. Dry the hob and the burner tops thoroughly after cleaning them.
What happens is this: The chemical makeup of white gas—which is basically the stuff you put in your car, minus certain additives—changes as it ages. In time it becomes a sort of varnish-like substance. It still burns, but can leave behind deposits that can clog up the burner in your stove.
Take apart your propane camping stove by unscrewing the burners. Hand-wash the burners, the cooktop, and the case with warm, soapy water. Let all of the stove parts dry upside down. Then, when everything is absolutely dry and there is no water left, put the stove back together again.
One of the more common and easy-to-fix reasons a gas stove keeps clicking is that grime, grease, and corrosion around the burner heads are interfering with the gas flow. Cleaning around the burner heads, igniter, and pilot hole can fix the clicking issue.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have a wildwood le 25bhbs and the only towing lights working are my signal lights. can’t get running lights or brake lights to work. I saw where it looked like the towing harness may have been pinched. So I repaired that, but, they still do not work. Any ideas? Is there a fuse somewhere I need to check? Do I need to hook the trailer up to my trailer hitch before they will work? Is there a wiring diagram or repair manual somewhere I can get? Any help would be greatly appreciated. Thank you.
ANSWER : There should be an inline fuse, check that first.
Read Full Q/A … : Coleman
I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.
Read Full Q/A … : Coleman
My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.
Read Full Q/A … : Coleman
I need to replace a gas valve for a furnace its a york stellar 133,000 btus the old valve number is 36E36-304 but is discontinued i need the new valve that replaces the old one and the price the model of the furnace is P3UCD20N10601A AND THE SERIAL NUMBER IS EBBM032176,can you show me a picture of the valve to compair it with my old valve
ANSWER : You will probably have to go with a “generic” gas valve. Try contacting Grainger to see if they can cross reference a workable solution.
Read Full Q/A … : Coleman
Trying to install a new fluro light, pull out old light to find 3 reds and 3 blacks 1 copper earth. What do I do to connect it up the right way??? When I pulled the old Fluro light out the 3 Reds were joined together with a connector ,two blacks were joined to one end of light wire, the other to the other end of the light wire,earth wire to the light case,the third black wire was connected to the wire from the ballast? Does this all make sense
ANSWER : No, this does not make sense but I have seen strange wiring before. There is power going from the light someplace else. Just connect it back up exactly as the old light was connected. It worked before so it will work again. If it works it is wired correctly. Without being there to check which wire was the hot wire and which was neutral it is impossible for me to say what is what. Make sure you connect the ground wire to the light chassis.
Read Full Q/A … : Coleman
Coleman 425 2-burner white gas stove pops out flame on low heat
ANSWER : There is water in your fuel. Drain the tank and flush it out with denatured alcohol. Refill with fresh fuel.
Read Full Q/A … : Coleman
Coleman rechargable lantern Model 5327A750. Have not used it in a while have left it on charge for over 24 hours. the night light works but the main light does not go on. Replaced the bulb and still nothing. Time for the trash can. Made in china….
It is only one (1) year old!!!!! Coleman has gone downhill@!!!
It is only one (1) year old!!!!! Coleman has gone downhill@!!!
ANSWER : Just read the charging instructions. Charge for 16-18 hours. If stored for more than 6 months recharge for the full 16 hours. Do not leave the lantern on after the battery has stopped, has overdischarging the battery can cause problems in recharging to a full charge. If this does happen, switch lantern to off and recharge for 40 hours.YES 40 hours. Only the LED is the only light to be used while charging. If you hane the other light on hi or low the battery does not charge.Hope this helps
Read Full Q/A … : Coleman
