Sport & Outdoor – Others

Weather Station – La Crosse WS 9128
The indoor unit stopped picking up a reading from the outdoor unit
I’ve tried changing the batteries (and waiting a day for it to re-find the signal) but still no reading
As far as I’m aware neither unit has been hit or damaged in any way
I think there maybe a reset button or function but can’t find the instructions
Thanks for your help
Experienced athletes share their insights in answering this question:
You have to have the station and the sencers close to each other when you put in the bats and then give them about ten mins

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Usually when the outdoor unit doesn`t turn on, it is because something tripped the circuit breaker. When this happens, you can easily reset it after locating the circuit breaker panel. If you find that the AC unit still does not work, the next place to look is the thermostat.
Outdoor units are also especially useful if you need to store some stuff, but don`t have a garage (or overstuffed your garage) at your home. The concept is the same: you leave your stuff outside in a covered area, roll down the door, and lock it up tight.
When your outside AC unit has broken down, but the inside unit still runs, it means you are dealing with a malfunctioning compressor. If you are lucky, the problem could be small (like a faulty relay or a burnt contactor) and easy to repair.
Your central air conditioning system has two key components: the indoor unit, and the outdoor unit. They work in tandem to keep your home comfortable year-round. The indoor unit is typically located in a closet or basement, and is near where your furnace filter is located.
A lot of air conditioners without an outdoor unit are marketed as `DIY` units. These units don`t have an outdoor unit, making installation easier. Usually, air is pumped through ducts at the back of the unit, so the unit needs to be installed against an outside-facing wall.
Dirty coils can also decrease the unit`s efficiency and might even cause a fire. Insects and other pests can nest in the AC unit if it`s not cleaned regularly, leading to health problems for your family. Mould and mildew can form on the AC unit if it`s not cleaned regularly, which can cause respiratory problems.
Regular cleaning of the outdoor unit is essential to prolong the air conditioner`s life. The outdoor unit consists of the compressor, refrigerant lines, condenser coils, and fan. The indoor unit`s evaporator coil absorbs excess heat from the home`s air.
CONCLUSION. Covering your air conditioner, especially with a full-length cover, leads to issues of mold, rust, and other problems. Your unit is made to withstand the snow and a cover is not needed for protection. It is recommended to only cover your AC during the fall months.
No, you should not cover your outdoor AC unit when it`s raining. You may reach for the umbrella when the rain starts to fall, but your AC unit was designed to withstand most elements of nature. The exterior case of the unit will not break down or malfunction in any way when covered in the pouring rain.
The outside portion of your air conditioner is most often referred to as the “condenser unit.” Whereas the inside part of your air conditioner is responsible for absorbing heat from your home`s air, your outside unit`s job is to release that heat to the air outside.
In short, the answer is no, air conditioners do not bring in fresh outside air. Rather, it takes the air inside your house and puts it through a heat exchange process. So, how exactly does it work? Generally, air conditioners move unwanted heat out of your home, thus lowering the temperature inside your home.
Outdoor Unit.

This is the part of an air conditioning system that contains the compressor, propeller fan, circuit board and heat exchange coil. It`s situated outside, and pumps refrigerant to and from its companion indoor unit. You`ll often hear this unit referred to as the `condenser` or `heat exchanger`.

The indoor unit will usually be located inside of a closet or the basement. If you know where your furnace is located, you should also know the location of the indoor unit. Inside, there will be a condenser coil with Freon, which is a type of refrigerant, inside of the box.
These systems include both an indoor unit and an outdoor unit. The indoor unit, typically a furnace or a fan coil, includes the evaporator coil and blower fan (air handler) that circulates air throughout the home.
Placing a condenser unit indoors in an attic or garage will reduce your system`s air supply, which will limit the amount of heat that it`s able to remove from your home. In addition, placing a condenser unit indoors will cause the space around it to heat up, and that heat can radiate into your home`s living spaces.
air conditioner without compressor like the ductless ac unit allows home owners to save on electricity costs. Instead of using a conventional air conditioning unit to cool an adjacent room, a 2.5 ton ac unit can be installed outside with a cooler in each of the rooms and then turned on when needed.
For example, if your AC is making a clicking noise and won`t start, it may be due to faulty or worn electrical connections to the system. These connections are aptly known as contactors. In order for your AC system to function properly it needs a signal from the contactor.
The outdoor unit, also known as the condenser unit, houses the compressor. The refrigerant gas enters the compressor where the molecules are compressed and become very hot. The compressor then sends the refrigerant gas to the condenser where the fans work to remove the heat from the refrigerant.
Look for it first around on the exterior of your machine, especially along the bottom edge near the ground. An AC`s reset button is typically red and visible, so it should be easy to spot. If you don`t see a reset button on the outside, it could be located inside the unit behind the service panel.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Read Full Q/A … : Sport & Outdoor – Others

What do you do when you are bored on a nice day?
ANSWER : I go for a walk with the dog. Or sometimes I putter around in the garden.

Go to the park… get some fresh air and exercise.

Read Full Q/A … : Sport & Outdoor – Others

Water and Rust under the Air Handler Unit of York HVAC
ANSWER : You may have holes in the condensate pan

Read Full Q/A … : Sport & Outdoor – Others

Lost key and the unit is locked. Any way a replacement key can be purchased or a way to get into the unit without a key?
ANSWER : Your best bet is to call a lock smith or if the locker is portable take it to a locksmith shop to save a house call fee. J.

Read Full Q/A … : Sport & Outdoor – Others

I have a 1992 yamaha waverunner wr500q, that didnt run so i took it to a repair shop and they said it was the CDI unit and it needed the carb cleaned and it would cost $1150.00 which i didnt have. But my dad cleaned the carb and we bought a brand new CDI unit, put it together and it was so exciting bc it started no problem but when we took it to the lake the next day it cranked but wouldnt fire up bc now its not getting a spark again. Please help!
ANSWER : THE CDI WOULD BE MY LAST CHOICE FOR THE LOSS OF SPARK PROBLEM, THE IGNITION PICKUP WOULD BE MY CHOICE, IT IS LOCATED BEHIND THE ENGINE FLYWHEEL, U MUST REMOVE THE FLYWHEEL TO GET AT IT, THIS REQUIRES SPECIAL TOOLS AS IT IS PRESSED ON, BELOW U WILL SEE A PICTURE OF THE PARTS UNDER THE FLYWHEEL, PART #5 IS THE IGNITION COIL PULSER, WHICH IS THE IGNITION SYSTEM PICKUP THAT TELLS THE CDI WHEN TO SPARK THE PLUGS, HERE IS THE PART NUMBER AND PRICE FOR THE PART.
SKU: 6K8-85580-00-00COIL, PULSER $94.12
OF THE PRIVCE AND PART NUMBER IS:

http://www.partforyamaha.com/pages/parts/viewbybrand/2/Yamaha.aspx

Read Full Q/A … : Sport & Outdoor – Others

Last year we could occasionally get the unit to stay on for a while. this year the unit has to have a button held. it occasionally will not respond with button held.
ANSWER : Can you tell the brand and model.This could be an issue with a faulty button switch that needs replacing. Or a loose connection that gets fix up when a pressure is applied.

Read Full Q/A … : Sport & Outdoor – Others

Once the dumbell is on the base the dial will not spin so you can not pick up any weights.

I can push the putton on the bottom when I am holding the unit with out any wieghts and the dial will spin but obviously once you put the handle on the base you can not manually turn this button.

ANSWER : Try setting the handle in the plates back onto the carrier(bottom). Lightly tap on each plate that is stuck. Now push the plates down (vertically) onto the bottom carrier. Now try turning the dial (side that was stuck). It worked for me. Have my 1090 plates were stuck on the handle. Good luck

Read Full Q/A … : Sport & Outdoor – Others

My name is Elena Jones, and I am a blog writer who loves sports and fixing and troubleshooting sports machines.
I also love the challenge of fixing and troubleshooting sports machines. I find it satisfying to be able to take something that is broken and make it work again.