Need instruction manual and parts list for Huffy D232 B portable basketball hoop. This was manufacturered approx 15 years ago. This has never b…

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

How do I get an instructional manual for the awning on my RV?

I have a mitchell riptide 80 spinning reel. I lost the screws and parts that hold the bail to the reel. I need a manual to show me the parts that I need to get. I also need the manual to show me exploded views so that I can clean and do maintainance on it.

Missing left side saftey and attachment screw

The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.

I have a TX500, never been used (just out of the box) and had to get an electrician to my home for this problem. It will start rolling but quits in a few seconds. The electrician believes that it is a problem in the sensor that rides at the belt. There is only one sensor in the pulley; he thinks that perhaps there should be two as there is a hole placement opposite the one that is in there. When the belt quits, it goes to a number 3 on the board which he thinks is the sensor as well. If he is correct, where do we get another magnet to place there? If he is not correct, please offer help. We did not get a owners manual in the box and surely could use one; where can we get one? Please help…thankyou

Need the wire diagram to rewire my Ariens lawnmover to bypass the safety switch. It is Ariens GT-19 model # 931026 Serial # 001463.
Can you help? It is an old Ariens mower but still runs good but now I need to bypass the safety switch in order to run it any longer. The local Ariens dealer said I need to go through the internet and get the wire diagram as they cannot give it to me directly. They told me I needed the wire diagram and the part involved in bypassing the safety switch. Hope this is all the information you need to help me.

Thank you. Roger Fielitz