to know how to adjust this belt…. thank you
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
If you could post your model number or serial number I will be able to help you.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

These components should all be touching the ground at the same time. If either the auger or wheels are not touching the ground, this means that the shave plate is adjusted too low and needs to be raised.
When the auger looses some drive, or slips under load, an adjustment can be made to tighten the auger drive belt. The auger engaging cable has a spring on the bottom end. Remove the belt cover to expose this spring. Perform this adjustment by moving the spring up a notch.
When the auger looses some drive, or slips under load, an adjustment can be made to tighten the auger drive belt. The auger engaging cable has a spring on the bottom end. Remove the belt cover to expose this spring. Perform this adjustment by moving the spring up a notch.
These components should all be touching the ground at the same time. If either the auger or wheels are not touching the ground, this means that the shave plate is adjusted too low and needs to be raised.
For removal of snow in normal conditions, such as a paved driveway or side walk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8″ clearance between the scraper bar and the ground.
These components should all be touching the ground at the same time. If either the auger or wheels are not touching the ground, this means that the shave plate is adjusted too low and needs to be raised.
If your gas blower is shaky or jittery when it`s on, there may be a problem with fuel combustion. Check the fuel or spark plugs—each is fairly simple to do. First, drain the fuel from the tank and refill it with fresh gas.
When the auger looses some drive, or slips under load, an adjustment can be made to tighten the auger drive belt. The auger engaging cable has a spring on the bottom end. Remove the belt cover to expose this spring. Perform this adjustment by moving the spring up a notch.
When the auger looses some drive, or slips under load, an adjustment can be made to tighten the auger drive belt. The auger engaging cable has a spring on the bottom end. Remove the belt cover to expose this spring. Perform this adjustment by moving the spring up a notch.
These components should all be touching the ground at the same time. If either the auger or wheels are not touching the ground, this means that the shave plate is adjusted too low and needs to be raised.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Hi,
After a recent snowstorm, the auger stopped turning on my Troy Bilt Two-Stage Snow Thrower (Storm 1130). I inspected it and found that I broke two shear pins and the auger drive belt appeared to need replacement. So, I replaced the pins and then replaced the auger drive belt, following the instructions in my operator’s manual. Now, when I hold down the lever that should cause the auger to start spinning, I get white smoke coming from the machine and a smell of burning rubber. I’m assuming I installed the drive belt incorrectly, but for the life of me, can’t figure out what I’m doing wrong. More significant snow is on the way tomorrow, so any quick answers/suggestions would be MOST appreciated!!!
ANSWER : The shear pins shear because the auger is stuck or the shaft it is on has seized bearings
work in that area

Read Full Q/A … : Sport & Outdoor – Others

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.

See less

ANSWER : Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up

Read Full Q/A … : Sport & Outdoor – Others

Machine will stop adjusting resistance. On start up the machine will usually work. I can go through the calibration procedure and it will calibrate and work normally for 4 or 5 resistance adjustments. It will then stop adjusting. It acts like there is a cable pulled and refuses to adjust, even though I am not getting the warning telling me to “Release cable”
I have modified the wiring harness so that the wires do not fall off from the stepper motor, so this is not the problem. If I shut the machine down and leave it for several minutes, it will come back and work normal again… for a while. I am wondering if there is a problem with the sensors that are detecting a cable pull? Is there a way to disable those sensors to see if that is the problem
ANSWER : I would think that your problem has possibly to do with a faulty power supply, component, see to my mind it is a thermal problem as it heats up,it goes faulty? The Voltage changes and it goes out of spec.. When left to cool, it then is OK… Usually, & from my experience this is a thermal problem. To see obtain some Freeze Spray, from radio Shack or similar,and spray components on the main power board, and others too, use it on any large heat sinked components and see if when you do this the fault clears. Then replace that component(s).

Or as you suggest the sensors that feed the inputs maybe with sensors though one has little option but to replace them and see if this clears the problem.

Read Full Q/A … : Sport & Outdoor – Others

I have an 8100 ES Reebok treadmill. There is a squeaking noise coming from the drive motor. It is coming from the non-belt side (if facing the front of the treadmill, the left of the drive motor. When the treadmill is turned off, I can manually move the walking belt in the walking / running direction and it will squeak. If I move it in the opposite direction, manually it does not squeak. Also, if I need to lubricate the bearings can you tell me how to get to them to do this. The motor has plenty of power and no other problems, only squeaking. I have sprayed a belt lubricant on the belt and also blown it all out with a can of compressed air (used for computer key boards).
ANSWER : Hi.the bearings in these machines should be lubricated and sealed for life. they are not designed to be touched. it sounds like you have done the important bits. belt lubrication and blowing out any debris that may be there. squeaks like this can be incredibly difficult to find, but can also be incredibly annoying.the main things that you can do is keep watching to try and find exactly where the squeak is coming from and check for anything wrapped around the edge of the roller.keep using the belt spray, and the compessed air.a good grade silicone lubricating spray used at the edges of the rollers, by the bearings and around the motor and gearbox unit may also help but do not get this spray on the belt as it can be very slippery.squeaks like this can start and stop on their own or develop slowly and go just as slowly.keep doing the maintenance you are doing, and use the silicone spray as described above.it may take a little while for the spray to work its way into the bearings as they are fairly well sealed but you should notice an improvement after a few days.please feel free to ask for further advice if you need

Read Full Q/A … : Sport & Outdoor – Others

I bought the Knoxx adjustable stock for my mossberg 500. The forend that comes with it is realy nice and Ide like to use it, but the end nut will not reach the threads. Do i need to buy a new adapter nut that is longer to secure my forend ? I saw one for sale by houge but wasnt sure if that would work on the knoxx forend ?? I realy like the forend sent by knoxx, would be a shame not to use it. What a waste to give that nice piece away and not give the adapter to use it ?? Thanks Noel
ANSWER : That forearm is designed for the 7 5/8″ slide action tube. I’m guessing yours is the 6 1/2″ slide action tube. Take the forearm off your tube and measure it with a ruler. From the very back edge of the action bar collar….that round part the bars are pinned to….all the way to the front edge of the threads. If yours is a 6 1/2″, the Hogue adapter won’t work. You’ll need to buy a new slide action tube. That Hogue adapter is meant to let you use the Hogue rubber coated forearm on your standard sized tube….the Hogue rubber forearm is a hair longer than the standard tube. It won’t give you the length to make up the entire shorter tube length. If you’re handy with a dremel, you could go adapter plus a bit of careful cutting but I won’t suggest you do it if you aren’t certain of your skills.

Read Full Q/A … : Sport & Outdoor – Others

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Read Full Q/A … : Sport & Outdoor – Others

I-run treadmill belt does not run
ANSWER : Maybe check the troubleshooting section of your manual. If you don t have one, check here.

Read Full Q/A … : Sport & Outdoor – Others