Sport & Outdoor – Others
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
Clear any debris and then try turning it back on, it may restart. Overheating can be caused by clogged strainers or dirt building up in/around the pump. A thorough clean will often help. Overheating also results from wear and tear, or scale building up on the rotor and bearings.
One of the most common causes of this phenomenon is due to debris blockages and obstructions. Weeds, waste products, stones, and other materials may have prevented them from functioning. And as the obstructions continue, the motor of the pump will just run even though the impellers do not spin anymore.
To check this, hold the magnet in one hand and the blades in the other hand and try to turn them in the opposite direction. Most impellers will turn slightly and then lock. If the blade keeps spinning on the magnet without ever locking, then your impeller is broken and needs to be replaced.
One of the most common reasons for a fountain pump to stop working is because the impeller is clogged. The impeller is responsible for moving water through the pump, so if it becomes clogged, the pump won`t function properly. To clean the impeller, try removing it from the pump and soak it in vinegar overnight.
Blocked Water Lines
Water lines run from the reservoir to the endpoints like taps or showers in your house. These lines, when clogged, can create higher internal pressure, causing the water pump to cut off abruptly even when there is room for more pressure.
Debris blocking the suction strainer or foot valve is the most common cause. A blockage in the intake line can cause the water in the pump casing to overheat and literally boil out of the casing causing the pump to lose prime.
Impeller failure
Erosion is caused by the suspended particles in the fluid being pumped. Impeller failure can also result from corrosion or cavitation. Corrosion is caused by chemical reactions between the pumped fluid and the metals used in pump manufacture.
At a minimum, you should replace your impeller according to your manual – for example, every 200 hours. Over time, the vanes become rigid and work less effectively, and you may see your engine overheating.
Pond pumps can typically last for around 1 to 3 years. However, several factors can affect their average lifespan.
This can be caused by a leak in the suction line, a clogged suction filter, or a problem with the check valve. Overheating: If the pump motor overheats, it will automatically shut off to protect itself from damage.
Pump Driver Overloaded
If the power drawn by the pump increases too much, it may ultimately lead to tripping or overloading of the motor. Some of the most common causes of pump driver overload include: The speed of the pump is too fast. An oversized impeller was installed.
There are several reasons your self-priming pump may not be working, these include: There is an air leak in the suction line: While the fluid is recirculating in the pump, it forces air out of the discharge as it is trying to create an area of low pressure.
Underfiling of Discharge Vanes
Underfiling opens up the discharge area of the impeller, which increases the impeller capacity. By making the pump larger, the head also increases because the head capacity point at design is moved back on the new curve in respect to the best efficiency point (BEP).
Tests prove that Globe`s Run-Dry® impellers outperform standard neoprene or rubber impellers and are guaranteed to run-dry for up to 15 minutes.
There are many methods for repairing the impeller of the water pump. There are many methods for repairing the impeller cavitation, such as ARC polymer composite material coating, powder spraying (welding), epoxy resin coating, and rubber and nylon composite material repair, etc.
Repairing impellers, where possible, is much less expensive than casting new impellers. With no need to make patterns or wait for foundry lead times, schedules are shortened, decreasing downtime.
Trimming should be limited to about 75% of a pump`s maximum impeller diameter, because excessive trimming can result in a mismatched impeller and casing.
Impeller Damage
As is the case for the housing of your pump, the impeller is susceptible to damage done by excessive heat during use. Dry running your pump causes friction, and this friction is strong enough to heat up the impeller, causing it to melt.
The pump may not leak coolant, but the pump mechanism itself may have failed. Over time the fins of the pump can actually wear down to the point where they are no longer moving coolant. Cavitation can eat away at the metal pump vanes and pump surfaces.
A pond`s pump should run 24 hours each day to ensure the pond`s water circulates through the filter to keep the water clear.
Running your fountain pump non-stop is the best way to keep your pond in good health. The constant circulation of water keeps the water clean and fresh and protects the flora and fauna that live in and around the water. The following are some of the top reasons to keep the pump running continuously.
If the pump starts to make a loud banging noise or is vibrating excessively, then you likely have an airlock. The air is making the pump work harder and the banging is caused by the pump stopping and starting repetitively. If you`ve noticed a sudden drop in your water pressure, this is again probably an airlock.
If the pump has proper volts at the motor but doesn`t run, the motor may be bad or it may need brushes. If it doesn`t have proper volts, check the current flow from the battery and whether a circuit breaker is tripped or a fuse is blown and needs replacing.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
See less
ANSWER : Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up
Read Full Q/A … : Sport & Outdoor – Others
How many hours a day should you run your pump? How many hours a day is it safe to run your intex pool pump, to insure a clean pool? I purchased my pool last summer and had major problems all year. When i got my pool my pump did not work and i had to wait a week for a new one to be shipped, well after that i had nothing but problems. My boyfriend said it was not good to let pump run all day but i think hes wrong. Can you give me some good tips on keeping my pool crystal clear?
ANSWER : Some pumps are 24hr 7days pumps some are not and should be on a timer. time usually run for 8 hours max a day. you can get a time from most pool leisure places. the pump will say if its a 24hr pump if not then would say its a timer type.
Read Full Q/A … : Sport & Outdoor – Others
I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.
Read Full Q/A … : Sport & Outdoor – Others
Caravan water heater not letting hot water through
ANSWER : Pipes are rusted and cloggen from the inside of them
Read Full Q/A … : Sport & Outdoor – Others
I have a TX500, never been used (just out of the box) and had to get an electrician to my home for this problem. It will start rolling but quits in a few seconds. The electrician believes that it is a problem in the sensor that rides at the belt. There is only one sensor in the pulley; he thinks that perhaps there should be two as there is a hole placement opposite the one that is in there. When the belt quits, it goes to a number 3 on the board which he thinks is the sensor as well. If he is correct, where do we get another magnet to place there? If he is not correct, please offer help. We did not get a owners manual in the box and surely could use one; where can we get one? Please help…thankyou
ANSWER : Hello,I believe the best thing to do at this point is to look for a way to get the manual of the device, this will give a full guide and better understanding on how to fix this problem.Check maualnguide.com to search for the manual of the device, the link provides almost all manuals to all device.Take care.
Read Full Q/A … : Sport & Outdoor – Others
I have coleman component 443 camping stove.
While pumping, the input air by the pump leaks just after the pump.
I guess the cap of pump should be replaced.
I tried to buy the part in Vancouver, unfortunately, I couldn’t.
I will visit seattle next week, is there any repair center in seattle?
While pumping, the input air by the pump leaks just after the pump.
I guess the cap of pump should be replaced.
I tried to buy the part in Vancouver, unfortunately, I couldn’t.
I will visit seattle next week, is there any repair center in seattle?
ANSWER : Yms3023000-The only official Coleman repair facility is in Wichita, KS. Try oiling the flexible gasket at the end of the pump. More often than not, a leaking pump is is due to the gasket drying out and not forming a proper seal.Hope this helps.Regards,DIYpro
Read Full Q/A … : Sport & Outdoor – Others
I have a Intex 18×4 above ground pool with original pump that takes type A filter cartridges. Did not set up last year and cannot find manual. The pump is leaking around the top after putting new filter in. I know I am not remembering everything I’m supposed to do with hose connecting into pump and pool when you change filters or flush pump. Can you help me?
ANSWER : For manual you can visit http://www.intexcorp.com.hk/proifv/proifv_dl_client.jsp?source=intexstore this link. Hope it will help you.
Read Full Q/A … : Sport & Outdoor – Others
