fine the last time I used it 2 months ago.
eXplorist GC Handheld Geocaching GPS Navigator

Experienced athletes share their insights in answering this question:
The application software of your GPS got corrupted I would suggest to bring it to the credited service center they are the only one have the data for your GPS.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

No Display on Boot: Possible Causes

The primary reason you get no display on your PC could be damaged or loosely connected cables. Other reasons may include incorrect display configuration, faulty or problematic GPU or RAM, incorrect BIOS configuration, faulty peripheral devices, or damaged PSU (Power Supply Unit).

Plug in other devices to the power strip and confirm they are operating properly. Double-check that your PC`s power supply on/off switch is on. Confirm that the PC power cable is properly plugged into the power supply and outlet, as it can become loose over time.
Power Button Not Working PC

However, sometimes you find nothing happens when pressing that button. The reasons for PC power button not working are various, for example, power cable, the dirty power button or power source issues, faulty PSU, and more.

You may notice that your computer slows down, freezes, crashes, or sends error messages. This is particularly worrisome if several programs are acting up and the problems persist even after rebooting. Problems with your mouse, monitor, or flash drive can also be warning signs.
Common symptoms of motherboard issues are similar to CPU problems: The system does not display anything; an error code appears; one or more beeps occur; the system locks; the system reboots; a Windows BSOD (blue screen of death) appears; or one or more of the ports, expansion slots, or memory modules fails.
If your PC won`t boot after removing and re-inserting the RAM, it`s possible that the RAM is not properly installed. Here are some steps you can take to try to fix the issue: Make sure that the RAM is fully seated in the slot. Sometimes it can take a bit of pressure to get the RAM to click into place.
One of the most common signs of CPU failure is the random freezing of your computer, usually after just logging into the operating system. The system won`t respond to any of your instructions. The mouse freezes on the screen and any attempt to use the keyboard will result in a series of short beeps.
A computer with a bad CPU won`t go through the usual “boot-up” process when you turn the power on. You may hear the fans and disk drive running, but the screen may remain completely blank. No amount of key pressing or mouse clicking will get a response from the PC.
A faulty, failing, or malfunctioning circuit or component (e.g., capacitor) can cause the computer to shut off immediately or not turn on at all. To help find potential problems with the motherboard, perform a visual check for blown capacitors or burnt circuitry that indicates the motherboard is damaged.
The Windows boot loop problem is often the result of a device driver, a bad system component or hardware such as the hard disk that causes a Windows system to spontaneously reboot in the middle of the boot process. The result is a machine that can never boot completely and is stuck in a reboot loop.
On the Install Windows screen, select Next > Repair your computer. On the Choose an option screen, select Troubleshoot. On the Advanced options screen, select Startup Repair. After Startup Repair, select Shutdown, then turn on your PC to see if Windows can boot properly.
On the Windows sign-in screen, press and hold the Shift key while you select Power > Restart .
Gaming itself won`t hurt your PC and even overclocking is unlikely to do serious damage. Any use will cause wear and tear that will eventually wear down your PC components, but gaming isn`t any more hazardous than anything else.
Can faulty RAM cause no display? – Quora. Yes, it can. Even any faulty part or loose connection can cause no display.
How Much Is a Motherboard? Well, the answer to this depends on the pricing tier of the motherboard in question. Some motherboards are as cheap as $50-60, but high-end motherboards can easily reach and exceed $200, with particularly niche enthusiast boards going as high as $800 – $1000!
Can faulty RAM cause no display? – Quora. Yes, it can. Even any faulty part or loose connection can cause no display.
A computer with a bad CPU won`t go through the usual “boot-up” process when you turn the power on. You may hear the fans and disk drive running, but the screen may remain completely blank. No amount of key pressing or mouse clicking will get a response from the PC.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.
ANSWER : Get to the manufacturer

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Slide out quit working and fuse on battery blows everytime I chan
ANSWER : Look under the coach near the slide and look for a pinched or bare wire. Sounds like you have a dead short to ground and could be difficult to find. Check the wiring to the slide motor, could be between the slide switch and the motor. Take a Volt meter and set it to Ohms. With the fuse out check to see if you get an Ohms reading between fuse wire and frame of coach. If you get a reading you have a short. Also check the power wire on the slide motor to motor case. If you get a reading the motor is shoted and needs to be replaced.Thanks for using FixyaJerry

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.

I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.

Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.

Hiya I have a fujifilm e-900 I have used the camera less than 20 times. The last time I used it I had no problems at all. I had left it sitting in it’s case for 6 months. Now when I try and us it I get the hand with lightning bolt on the lcd. Which I assume means the battery encasement is open. It isn’t open. The camera turns on no problem then when I try and use any function it shuts down. How do I fix this?
ANSWER : The hand with the lightning bolt icon usually means the camera is telling you that there is not enough light and you need to pop the flash up before you take a picture.
If you haven’t used the camera for a while have you tried fresh batteries or charged the 2 re chargeable AA’s that came with the camera?