Loose end cap on easton syn bat who can I get to repair it around Houston, Texas out of warranty

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

Easton synergy softball bat

We have an Easton CNT synergy fastpitch bat and the end or plug broke out of it but everything else is ok. Is there someplace we can get a new end. Thanks

I bought a Rio 30′ piece of sink tip T-11 which included 3 loop connectors. At the same time I bought extra loop connectors (4-6 wt). When I opened the sink tip the LCs had a very narrow end which opened into a slightly larger diameter nearer the loop. the ends are frayed.
My question is, do you have any hints as to how to apply the included loop connectors to my sink tip. I had no problem getting ther 4-6 wt LC and BTW, I tied a nail knot over the LC near the end of the sink tip line and super glued the collar place over the end of the LC where the line enters the LC.

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.

Taylor made driver repair

1988 Yamaha 4 wheeler slow crank