Lawn mower will start and will run if im pumping the bulb then shut off changed oil gas filter with air pump i blue out carb and changed spark…

The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.

I have a 1996 yamaha wave venture 1100….ran greatsat for 2 yrs..started but only ran for spray into carbs….drained fuel started and ran good. Started about month later and would only run as long as primed with starter fluids…checked fuel filter(ok)…fuel flow to fuel pump ok…output of fuel pump appears ok….but engine will only run as long as starter fluid/gas is sprayed into carbs. I don’t think it’s the carbs as it ran great a month ago…now it’s starving for gas flow….so it appears to be a fuel delivery problem…what would be the sequence of tests up to tearing into the carbs? is there a fuel filter inside the carbs? remember it fires off great when primed…until the fuel spray is consumed…

2005 4 stroke yamaha 150 550hrs. normally use every week but due to surgery not used for 10weeks. Just before I went down I changed internal fuel filter, and zincs in motor. finally put in sunday. motor started fine left dock hit the power and started to come up on plane then stuttered and died. changed the external fuel/water seperator pump up the primer and started up again. with in a minute died down again. limped back to dock checked fuel filter and plug wire connections. pumped up primer and left dock went right onto plane for maybe 150yds then coughed and died. I could pump up primer and it would run but then die out. the fuel filter at the front of the engine would run dry until I pumped it up again. If it were a car I would suspect a leak in a fuel line but I can’t find any sign of one.
before we launched I put 10 gallons of fresh fuel in and added another bottle of ethanol stabilizer (CRC brand)
what proceedure should I follow to isolate the problem? I am a fairly competent mechanic as far as cars and trucks go. I don’t really want to have to take it to a marine mechanic.

I have a 99 yamaha f100 four stroke outboard. Problem I have is boat will acclereate fine get up on plane and after running for about a mob at wot will decell and only run around 4500 rpm. Then after coming back to idle will have a slight miss then run smooth and repeat every run. Changed the plugs and fuel filters alll oe yamaha has fresh oil timing belt is good any ideas will help or fuel psi spec. I am an ase master automotive tech so I know alot about engs. To me it feels like it’s running out of gas. Like the carb bows are full when I take off but then runs out after running wot. Any info will help

I have a 2004 60 hp yamaha 2 stroke outboard engine that doesn’t start or run well. Once warm and in the water it will idle in nuetral and also in gear. It accelerates in neutral but will die or lack power if I increase throttle while in gear. Engine will somtimes get to top speed but often while running at top speed engine will start to slow rapidly. Engine has full range of operationout when out of the water where there is no load on engine but is still difficult to cold start. Before these recent problems the engine sat up for several months and I had to change the impeller and spark plugs. Spark plugs fire, cylinders have proper pressure of 100, 100, and 110. I cleaned some fuel lines and filters and got new gas.

Water in the fuel tank of my Zodiac dinghy with Yamaha 2001 50 HP

Starting my Mojave 250