New York Giants Eli Manning Jersey

I have the i-run reebok treadmill where the belt does not run however the motor can still be heard (i.e. the belt seems like it’s stuck). The belt is still able to be manually moved…does anyone know how to fix it?

Thanks!

Experienced athletes share their insights in answering this question:
Maybe check the troubleshooting section of your manual. If you don t have one, check here.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Check the drive belt for proper alignment. With the cover still off, check over the wire and cable connections, as they may have become loose or disconnected during shipping or assembly. Make sure connections are secure and no wires are crimped, damaged, disconnected or burnt.
Treadmills require lubrication to limit the amount of friction between the platform and belt. When the friction increases to a certain point, the machine is automatically set to power off. This may be the cause for the machine to stop working suddenly. Try lubricating the belt.
If you`ve noticed your belt slipping a little or you`ve recently adjusted your belt, it might be that it`s either too tight or loose, causing the slowing down. Though tighter belts seem better, they can cause the drive system to work harder to keep the belt running.
Run your hand along the underside and top to check for signs of excessive wear. This may come in the form of discoloration or extreme smoothness. Discoloration for most treadmill belts will seem dark, almost black. And if some areas are too smooth, then it may be a sign that you need a treadmill belt replacement.
You`ll need to purchase 100-percent silicone lubricants. Non-silicone lubricants such as WD40 contain additives that could potentially damage the belt. Fasulo advises getting a bottle with an extendable nozzle, such as Spot On Treadmill Lubricant or Godora Treadmill Lubricant.
A damaged walking belt, improper belt tension, lack of belt lubricant or a bad drive motor can cause the walking belt to slow down when you step on the belt. Unplug the treadmill, then check the walking belt for damage and replace the belt if it`s torn.
How long should my belt last? Generally, a 1-ply running belt will last 300-500 hours of use depending on the way it is maintained. This is approximately 3-5 years for the average user. A 2-ply belt will last much longer 5-10 years.
How much does it cost to replace a treadmill belt? Replacing a treadmill belt will typically include the cost of the labor and the parts. Labor often costs $100 to $200 an hour, while a belt can cost $200 to $300 on its own.
Proper maintenance for your treadmill, including lubrication, is a must do! Depending on your model, you may sometimes have to lubricate the running deck with paraffin wax. The reason for applying wax to the running deck is so the running belt moves smoothly over the deck surface.
LUBRICANT-NEVER use WD40, 3 In One Oil, Vaseline or any non approved treadmill belt lubricant. For best results use manufacture recommended lubricant. LUBRICANT APPLICATION: Check under the walk belt to see if debris needs to be cleaned.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a 99 yamaha f100 four stroke outboard. Problem I have is boat will acclereate fine get up on plane and after running for about a mob at wot will decell and only run around 4500 rpm. Then after coming back to idle will have a slight miss then run smooth and repeat every run. Changed the plugs and fuel filters alll oe yamaha has fresh oil timing belt is good any ideas will help or fuel psi spec. I am an ase master automotive tech so I know alot about engs. To me it feels like it’s running out of gas. Like the carb bows are full when I take off but then runs out after running wot. Any info will help
ANSWER : I have exactly the same problem with my Yamaha F100, have you got any solutions yet?

I have an 8100 ES Reebok treadmill. There is a squeaking noise coming from the drive motor. It is coming from the non-belt side (if facing the front of the treadmill, the left of the drive motor. When the treadmill is turned off, I can manually move the walking belt in the walking / running direction and it will squeak. If I move it in the opposite direction, manually it does not squeak. Also, if I need to lubricate the bearings can you tell me how to get to them to do this. The motor has plenty of power and no other problems, only squeaking. I have sprayed a belt lubricant on the belt and also blown it all out with a can of compressed air (used for computer key boards).
ANSWER : Hi.the bearings in these machines should be lubricated and sealed for life. they are not designed to be touched. it sounds like you have done the important bits. belt lubrication and blowing out any debris that may be there. squeaks like this can be incredibly difficult to find, but can also be incredibly annoying.the main things that you can do is keep watching to try and find exactly where the squeak is coming from and check for anything wrapped around the edge of the roller.keep using the belt spray, and the compessed air.a good grade silicone lubricating spray used at the edges of the rollers, by the bearings and around the motor and gearbox unit may also help but do not get this spray on the belt as it can be very slippery.squeaks like this can start and stop on their own or develop slowly and go just as slowly.keep doing the maintenance you are doing, and use the silicone spray as described above.it may take a little while for the spray to work its way into the bearings as they are fairly well sealed but you should notice an improvement after a few days.please feel free to ask for further advice if you need

The Walking Belt keeps staying close to the right side
ANSWER : Speed the belt up to around 4mph while adjusting the belt. you will see it centre very quickly. once centered leave it to run for a couple of minutes to see if it stays central.

Recently, I was using my Horizon CST 4.5 treadmill when the power on the treadmill and the room it was housed in went out. I reset the cicuit breaker and tried to get back on the treadmill. It turned back on, counted down from 3, and the time began however the running surface(track) would not move. I lifted the front end where the motor and belts are housed. I noticed that the belt was still intact. Unsure if motor is burnt out. Any help would be appreciated.
ANSWER : There is usually a small breaker on treadmills that pops out and you have to push it in to reset it. Take a look around the front of the treadmill and see if you can locate the breaker and reset it and the treadmill should work normally.

Belt just runs at max speed automatically 🙁
ANSWER : Yes. Replace the speed sensor. In the unlikely event that the problem still is not solved replace the circuit board. J.

Treadmill belt slipping
ANSWER : Hi, I have a Duratec usermanual, you can email me at crowsrluved at hotmail dot com and i’ll email it to you, I think it should explain everything to you.

2008 Yamaha vx deluxe will only run about 30 mph
ANSWER : If the motor is reaching full revs look at the jet assemby for fouling or prop damage. If it is not reaching full revs get authorised mechanic to fix it, it will be cheaper in the long run.