I purchased a Mossberg 500 over/under breach load shotgun two years ago. It is my first shotgun.It started misfiring last summer, either firing…

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.

See less

I bought a new mossberg 590 a1 shot gun a month ago, I love the gun but its having a couple of problems, the first problem is that when shooting every once in a while i get sprayed in the face with exuast from shooting through the safety very scary! any ideas whats causing this? how to fix it? second is that some times the fireing pin sticks and the gun will not discharge a round? the third problem is that i have had feeding issues with gun where it will not realice a gound from the tube, ive taken a tip of a knife to the stuck round in the tube and it prys out with little effort, these problems dont happen every time i go shooting, just every once in a while, but they a happening more and more, im conserned cause the gun is brand new, and i wanna be safe while shooting, can you guys help me? any ideas/solutions? please help!!!!!!!

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.

I have a Kohler Condidant 5 Generator that will run as long as you hold the start button in. It dies when you let off. I have a harness for the remote switch but no switch – It also will start the generator when you cross the red and black wire and run as long as you hold them together. There are 3 wires to the main switch and 5 to the remote switch. Does the starter stay engaged the whole time you hold the start switch or does the computer release the starter once it is running? The Generator is producing electricity because I tested it while holding the start button. Some where is a wire that shold tell it to keep running. I have read online many descriptions of the same problem, most are told the board is bad so they replace it and still have the problem. Have not found a solution. Talked to a marine machanic today and he said he fixed his friends generator doing the same thing by running a bypass wire but he couldnt remember exactly what he did it was a long time ago. Can anyone help me. Thank you

My mossberg 500 drops a live shell without chambering it after the first couple. I have removed the plug to increase the maximum shell capacity. I have kept it full loaded in my safe for several years, and the problem appears to be new. Would the magazine tube spring be weakened by storing it loaded for an extended period of time? I have purchased a new spring but do not know how to install it. It could also be a problem with the elevator I am told. Is this something I can fix myself?

I have a TX500, never been used (just out of the box) and had to get an electrician to my home for this problem. It will start rolling but quits in a few seconds. The electrician believes that it is a problem in the sensor that rides at the belt. There is only one sensor in the pulley; he thinks that perhaps there should be two as there is a hole placement opposite the one that is in there. When the belt quits, it goes to a number 3 on the board which he thinks is the sensor as well. If he is correct, where do we get another magnet to place there? If he is not correct, please offer help. We did not get a owners manual in the box and surely could use one; where can we get one? Please help…thankyou

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.