Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

To use a metal detector, stand in a comfortable position and extend or retract the stem so that the coils hover just above the ground when you hold the unit. Walk slowly as you swipe the machine from side to side.
For the hand-held metal detector, the generated energy is in the form of a magnetic field. The interaction of this magnetic field with certain types of objects in the region around the detector and the ability to detect this interaction are the basis of operation for hand-held metal detectors.
Like the number chart you`ve seen earlier, the tone of beeping of your metal detector follows a similar pattern. Low pitches usually indicate low-value metals, while high pitches indicate high-value metals like silver and gold.
Setting your metal detector to achieve the best sensitivity for your needs requires adjusting the frequency settings. Finding the right balance is challenging because low sensitivity settings won`t find contaminants, and high sensitivity settings will result in too many rejections.
The DISC LEVEL control is used to adjust the detector`s response to unwanted trash metal when operating in the Discrimination MODE. At the lowest setting (MIN), the detector will ignore most iron objects, but will still respond to light foil, bottle caps, pull tabs and most other metal objects,.
Modern walk-through metal detectors use PI, or pulse induction technology. PI systems send out short and powerful bursts of currents through a coil of wire and each pulse generates a short magnetic field.
Most metal detectors can detect coins at an average maximum depth of 10 to 16 inches. Metal detectors transmit radio frequency signals from the search coil to locate the targets from the ground`s surface to a depth of over 20 feet for large deep treasures.
Typical minimum depth range from 25 to 30 cm underground. This range is obtained with very rough quick made coil (not optimized) using 10 cm diameter object. With optimizaed coil range of detection increase to more than 40 cm. The metal object detection is indicated by LED.
There are two primary types of security metal detector used in public: Hand held metal detectors or security wands.
All metal detectors need calibrating. Each manufacturer will tell you that at least one annual visit is necessary to keep the detector operating at its best.
A metal detector is capable of detecting all types of metals. These metals are divided into two categories, the first is ferrous and the second is non-ferrous. Ferrous refers to any metal that is attracted to a magnet. Ferrous metals are the easiest to detect due to the fact that they have magnetic properties.
Metals such as iron, nickel and cobalt are detected by passive and active metal detectors. Other metals, such as copper, brass and aluminum, are detected only by active means.
Sensitivity is the measure of a metal detector`s ability to detect a specific type and size of metal contaminant. The better the sensitivity of the metal detector, the smaller the pieces of irregular-shaped metal it can detect.
Metal detectors use electromagnetic fields to passively or actively detect the presence of metallic objects. Passive detection measures the changes in the Earth`s magnetic field caused by an object.
There are three main parts in the metal detector circuit: the LC Circuit, the Proximity Sensor , output LED and the Buzzer. The coil and the capacitor C1, which are connected in parallel, will form the LC circuit. Proximity sensor(TDA0161), is triggered by this LC cirucit if any metal is detected.
Metal detectors use electromagnetic fields to passively or actively detect the presence of metallic objects. Passive detection measures the changes in the Earth`s magnetic field caused by an object.
The most common technique is to slowly sweep the detector back and forth across the ground. The detector`s magnetic field will cause any metal objects in the ground to create an electric current.
Modern walk-through metal detectors use PI, or pulse induction technology. PI systems send out short and powerful bursts of currents through a coil of wire and each pulse generates a short magnetic field.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I need a manual for bounty hunter quick draw 2 metal dector
ANSWER : You can download the full users manual at http://www.detecting.com/products/
here is the link to your quick draw II detector:
http://www.detecting.com/pdffiles/qdiiman.pdf
If you want to purchase a hard copy of the manual look on eBay under Bounty Hunter Manual cost is around $6.

Read Full Q/A … : Sport & Outdoor – Others

I need a manual for my bounty hunter metal detector
ANSWER : You can download the full users manual at http://www.kellycodetectors.com/pdf/manuals/pioneer505.pdfIf you want to purchase a hard copy of the manual look on eBay under Bounty Hunter Manual cost is around $6.

Read Full Q/A … : Sport & Outdoor – Others

How do I get an instructional manual for the awning on my RV?
ANSWER : Kindly download the manual from the following website

http://bryantrv.com/owners.html

thank you

Read Full Q/A … : Sport & Outdoor – Others

Manual for gc-1013 metal detector – Sport & Outdoor – Others
ANSWER : Hi, did you find a manual/instructions for this as i am too looking for one.

Read Full Q/A … : Sport & Outdoor – Others

Manual for metal detector gc1055 – Sport & Outdoor – Others
ANSWER : I hope that attached video will be helpful for you..

Read Full Q/A … : Sport & Outdoor – Others

I have a mitchell riptide 80 spinning reel. I lost the screws and parts that hold the bail to the reel. I need a manual to show me the parts that I need to get. I also need the manual to show me exploded views so that I can clean and do maintainance on it.
ANSWER : Hello LVAmtrak,

Here is a link to the schematic and a site where you can purchase parts if necessary.

http://www.mikesreelrepair.com/schematics/displayimage.php?album=15&pos=270

Hope this helps.

Thanks,

Pat

Read Full Q/A … : Sport & Outdoor – Others

Need the wire diagram to rewire my Ariens lawnmover to bypass the safety switch. It is Ariens GT-19 model # 931026 Serial # 001463.
Can you help? It is an old Ariens mower but still runs good but now I need to bypass the safety switch in order to run it any longer. The local Ariens dealer said I need to go through the internet and get the wire diagram as they cannot give it to me directly. They told me I needed the wire diagram and the part involved in bypassing the safety switch. Hope this is all the information you need to help me.

Thank you. Roger Fielitz

ANSWER : Here is owner manual:http://apache.ariens.com/manuals/030305C.pdfusually the switch is behind the ignition, sometimes at the N position of gearshift, just look for a switch with one wire coming in & one going out (usually the same color); disconnect the two wires & jumper them together to bypass the switch. Looks like yours has one under the seat.

Read Full Q/A … : Sport & Outdoor – Others