Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Here is a direct link to the User’s Manual for a Minn Kota Classic 38:

http://www.minnkota.com.au/images/stories/user_manuals/Endura/Classic%2028.pdf

To view the Owner’s Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner’s Manual.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, then follow the onscreen instructions to install the software on your computer.

Please comment back here to this page if you have any details to add, have any questions, have difficulty accessing the links, or just require further general assistance and I will respond as soon as I see it.

I hope that was helpful to you, good luck and take care.

Joe.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

The first letter of the serial number determines the year. The following three numbers determine what day of that year the trolling motor was made. Example 092 is April 2nd.
All Minn Kota® products come with an adhesive label that lists the serial and model numbers.
The serial number is located inside the mount near the motor rests, this can be seen when the motor is stowed.
starting with the Ulterra. The newly re-designed motors were introduced for model year 2017 and featured improvements in build quality, materials, electrical components, bluetooth pairing and GPS. Minn Kota left no stone unturned and far as we are concerned.
There are several ways to check the power on your trolling motor. You can briefly connect the trolling motor to a battery, then turn it on. Don`t run it this way for very long, though. If you want to run it for longer than a few seconds, fill a bucket or trash can with water and test it there.
Answer: Every Mercury outboard has a serial number label located on the transom bracket area of the engine. The latest serial number labels display a 2-digit number in a box at the lower right portion of the label. These digits coincide with the last two digits of the year in which the outboard was manufactured.
The Serial Number is engraved into the side of the transom bracket where the holes for the tilting mechanism are located.
a) The Minn Kota charger will only charge 12 volt 6 cell lead acid batteries. Do not connect the output of the charger to any other voltage or type of battery.
Definition. A group of data, summarized by a four-digit identification code, that defines the conditions and business procedures involved when assigning serial numbers to items of material.
Open the Command Prompt by pressing the Windows key on your keyboard, then pressing X. Select Command Prompt (Admin) on the menu. Type wmic bios get serialnumber and then press Enter on your keyboard.
Every Minn Kota motor is designed, serviced and manufactured by real American anglers in Mankato, Minnesota.
You can expect a battery like this to last a minimum of 2-3 years, which can be extended by maintaining electrolyte (acid) levels with distilled water and using a Minn Kota Precision charger`s deep equalization mode to combat sulfation.
They typically last around 2-3 years and may require some sort of maintenance.
Tips for Preserving the Lifespan of a Trolling Motor Battery

Again, many factors influence a battery`s lifespan, but they typically last at least five years and can be viable for up to 10 with proper maintenance.

Fortunately, it`s fairly simple to find your boat`s build date. (See “HINs By The Numbers” below) The information with the boat`s model year is contained in the hull identification number (HIN), which is a label permanently affixed to the boat. The number includes a date assigned by the builder.
Let`s do the math: a 30-pound thrust trolling motor can support up to 1500 pounds, a 40-pound thrust can support up to 2000, and a 55-pound thrust can support up to 2500 pounds safely.
Modern electric trolling motors are designed around a 12-volt, 24-volt or 36-volt brushed DC electric motor, to take advantage of the availability of 12-volt deep cycle batteries designed specifically for marine use.
The VIN does not use I, O, Q, U or Z. From 2001 to 2009, the numbers 1 through 9 were used in place of letters. The alphabet started over from A in 2010 and will continue until 2030.
Most gasoline-powered vehicles also have the VIN number stamped on the front of the engine block. You will find your VIN number on your car insurance card as well as on the title and registration for the vehicle. For motorcycles, the VIN number is usually found stamped on the frame neck.
A fully charged 12 volt battery should read at 12.6 volts on the multimeter. If the reading is lower than this, you`ll want to charge your battery with either a battery charger or by taking your car for a drive.
If your boat is 16-foot or smaller, a high-thrust 12-volt model will be adequate for the conditions that you will face. If your boat is any longer, moving up to a 24- or 36-volt system is the only way to go for hassle-free boating.
Most serial numbers have at least six or seven characters, and some serial numbers have twenty or more.
A serial number is a unique identifier assigned incrementally or sequentially to an item, to uniquely identify it.
Model and serial numbers are used to identify a specific product. The model number differentiates between models of devices—for example, iPhone® 13 and iPhone X. Many devices can share a model number, which means they`re the same model. But every device has its own unique serial number, sometimes abbreviated as S/N.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My daughter has a sweet pea scooter that had been blowing fuses and the motor got hot. Im sure the motor is shot. but my question is can anyone tell me if the motor would be the only thing I need to c
ANSWER : Find out whether it is 6 volts or 12 volts and there should be two wires that feed the motor either cut or splice and attach another set of wires with fuse in the line (simular to jumper cables) raise the back tire so it does not touch the ground and place jump wires to the negative and positive of the battery.If the motor moves in either direction without blowing the fuse the motor is good if not then its bad. Uses the same amperage fuse

Read Full Q/A … : Sport & Outdoor – Others

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Read Full Q/A … : Sport & Outdoor – Others

TC5000 and after extended use I smell burning and upon removing the belt cover and drive belt I felt of the motor on the motor side of the drive pulley and it was ”red-hot”, obviously the source of the smell of the burning. The motor spins freely without any rubbing noise. The drive pulley (motor side) and the tread pulley appear to be alligned. One curious thing is that the threaded motor output shaft is recessed about 3/8” from the outside edge of the pulley. Could it be the bearing on the pulley side of the motor? I am dumbfounded as to what the solution might be. Note that I could not enter the exact product as my model seemed to be invalid. My model is the TC5000. Thanks [email protected]
ANSWER : Just because it spins freely doesnt mean it cant have a shorted winding. Id send it back where it came from or at least replace the motor.

Read Full Q/A … : Sport & Outdoor – Others

I have a Minn Kota Endura 50 trolling motor. There is a bushing and thumb screw that secures the shaft to the desired depth. The plastic threads that the thumb screw sets into have stripped. Is there a replacement part? The same thing has happened on three other Minn Kota motors I have had. Obviously I have been over tightening them
ANSWER : HELLO,YES IT CAN BE REPLACED ANDYOU CAN VISIT THE SITE BELOW FOR PARTS ORDERING.http://electric-outboard-motors.co.uk/accessories.htm ORhttp://www.lakepowelldiscountmarineelectronics.com/minn-kota.htmlWISH YOU GOOD LUCKTAKE CARE.

Read Full Q/A … : Sport & Outdoor – Others

I have a 1997 motor guide wireless 24volt Big Water trolling motor. hooked it up to the batteries and put in a new 9volt battery in the foot pedal. the lights come on on top of the motor head and the foot pedal beeps, but the prop doesnt turn or spin (like there is no power to the bottom of the motor) any suggestions to what the problem is or how to fix it? (just bought the motor from a lady who’s husband died. dont have any manuals)
ANSWER : Hello there, as you said the power does not get to the bottom of the motor. The motor could be faulty or just completely bad. First you have to determine that the motor is good until you can determine this it is quite impossible to determine if there can be any fix. Take out the motor and try to power it on its own if it works fine then the problem is not from the motor but most likely the problem is from the motor. Let me know what your findings are. Hoping to hear from you soon.
Thank you for visiting FixYa.

Read Full Q/A … : Sport & Outdoor – Others

I have an 8100 ES Reebok treadmill. There is a squeaking noise coming from the drive motor. It is coming from the non-belt side (if facing the front of the treadmill, the left of the drive motor. When the treadmill is turned off, I can manually move the walking belt in the walking / running direction and it will squeak. If I move it in the opposite direction, manually it does not squeak. Also, if I need to lubricate the bearings can you tell me how to get to them to do this. The motor has plenty of power and no other problems, only squeaking. I have sprayed a belt lubricant on the belt and also blown it all out with a can of compressed air (used for computer key boards).
ANSWER : Hi.the bearings in these machines should be lubricated and sealed for life. they are not designed to be touched. it sounds like you have done the important bits. belt lubrication and blowing out any debris that may be there. squeaks like this can be incredibly difficult to find, but can also be incredibly annoying.the main things that you can do is keep watching to try and find exactly where the squeak is coming from and check for anything wrapped around the edge of the roller.keep using the belt spray, and the compessed air.a good grade silicone lubricating spray used at the edges of the rollers, by the bearings and around the motor and gearbox unit may also help but do not get this spray on the belt as it can be very slippery.squeaks like this can start and stop on their own or develop slowly and go just as slowly.keep doing the maintenance you are doing, and use the silicone spray as described above.it may take a little while for the spray to work its way into the bearings as they are fairly well sealed but you should notice an improvement after a few days.please feel free to ask for further advice if you need

Read Full Q/A … : Sport & Outdoor – Others

I need a owners manual for 1994 coleman pioneer cheepasake popup
ANSWER : Http://www.colemantrailers.com/download-owners-manuals

Read Full Q/A … : Sport & Outdoor – Others