Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Hello! Go to the following link to acquire a vented gas cap for your ice auger.www.outdoordistributors.com/Tecumseh/tfuel.htmlGuru……….saailer

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Re: Fuel mix for jiffy model 30 ice augers? 10.5 ounces of oil to 1 gallon of fuel. Use non ethanol gas of you can.
The ratio for Tecumseh TVO85 (3 hp), AV520 (3 hp), AV600 (3.5 hp), TMO49 (2 hp), TC200 (1.6 hp) and TC300 (2 hp) engines is 40:1. TIP: We recommend preparing a mixture in a one gallon gasoline container to keep the mixture as fresh as possible.
Premium 40:1 Two-Cycle Smokeless Synthetic Blend Engine Oil with Fuel Stabilizer for use with all brands of 2-Cycle Ice Drills. New reformulated 40:1 gas mixture reduces emissions. JIFFY® has taken the next step for a cleaner environment!
Such augers can survive farm use for up to 30 years and longer with their original tube and flighting. When the time comes, the flighting with the wear edge should be easily replaceable without having to weld or replace the entire length of flight.
Only Jiffy® Power Ice Drills use high-speed, single reduction gearboxes. These gearboxes turn the ice drills counter-clockwise. All other drills turn clockwise.
For a 50:1 ratio of gas to oil, use 2.6 fluid ounces of oil per gallon of gas.
You want to mix 2.6 ounces of oil to one gallon of gasoline for a 50:1 mixture. If you`re mixing up two gallons of gasoline you will have to mix 5.2 ounces of oil to two gallons of gasoline for a 50:1 mixture.
Twenty four to one (24:1) is a ratio used by some older 2 stroke motors, largely it seems to have been replaced with 25:1 or 50:1 these days. The ratio is not the easiest 2 stroke ratios to calculate. To make it easier you can use the following old school reference chart.
Use a 32:1 gasoline to oil ratio. One gallon of gasoline combined with 4 oz of two-cycle engine oil. If you are in the state of California, use a 2-cycle oil mix ratio of 40:1.
Most augers are designed to run at 540 rpm, so it`s important to use the appropriate tractor.
Use unleaded regular gas only. Run earth auger with a 50:1 ratio. Fuel must be mixed in a container outside in a well ventilated area.
MTD two-cycle snow throwers use a 50:1 ratio of gasoline to 2-cycle oil, which is one gallon of gasoline to 2.5 oz of 2-cycle oil.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

What should the gas oil miz ratio be for an older model 30 jiffy ice auger…

fustarted fisherman

ANSWER : Hello,
I work out at a remote fishing lodge in Alaska and the Jiffy auger we have here says 24:1 on the unit but I know for a fact ( cu’z I do the mixing ) that we run it using a 40:1 mix Ratio and it works great.
I have heard stories from other fishermen that they are running ‘ Amsoil* ‘ in there Jiffy augers at a mix ratio of 80:1 and they say that it cut down on the smoking of motor.
fish on,stay warm and have fun,

c…

Read Full Q/A … : Sport & Outdoor – Others

I have a older model # 30 jiffy ice auger and i can not seem to keep it running consistanly. I was wandering what the carburator adjustments are. The low idle screw and the high idle screw where do I start for as how many turns out for each one.

Thanks Randy

ANSWER : Hello Randy. I can talk you through making adjustments to your Jiffy ice auger engine.

1. Read through the whole list before you start adjusting. 2. Close both jets GENTLY3. Open the Low speed 1/4 turn4. Open high speed jet 1 1/4 turn
5. Start engine.6. Adjust low speed until idling smoothly.7. Open her up wide open.8. Adjust High speed until engine transitions smoothly from idle to high speed without bogging.9. Shut engine off. Let it cool.10. Once engine is cold. Fire it up and let it idle for 30 secs. Open it up wide open again. Adjust if necassary.NOTE 1: The trick with the Jiffy’s is to tune them during cold (ice fishing) weather.NOTE 2: Low speed screw,the one on the left.NOTE 3: High speed on the right.

Good luck ice fishing! Regards, Joe

Read Full Q/A … : Sport & Outdoor – Others

The pull cord on my jiffy ice auger model 30 has broke and I need a new one. I do not need a new ice aguer just the pull cord which is located at the top.
ANSWER : If you just need the cord — most hardware stores do carry replacement cord ( sold by the foot ),, if you look in the chainsaw department you should be able to find the size that you need. as soon as you have the cord you can re spool the winding unit and this will restore the pull start function.
you can also buy the cord at your local lawn and garden shops,snowmobile shops or chainsaw shops.
if you have any further questions about this problem — please feel free to ask,

c…

Read Full Q/A … : Sport & Outdoor – Others

My son was using the model 77 ice auger Jiffy when it just quit. has gas and spark but i cant get it to start it is about 8 years old
ANSWER : Bad gas. Drain and refill with fresh fuel/oil mixture.

Read Full Q/A … : Sport & Outdoor – Others

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.

Read Full Q/A … : Sport & Outdoor – Others

Both augers will not turn to blow snow thru shoot.
ANSWER : Check the shear pins

Read Full Q/A … : Sport & Outdoor – Others

Mule 610 will not start. Was running fine, plowing snow and it starting acting like it was running out of gas and stalled. Put gas in put it won’t start and acts like it is not getting gas. Could the gas line have frozen due to the depth of the snow?
ANSWER : Did you ever find the fix for your mule?

Read Full Q/A … : Sport & Outdoor – Others