Shakespeare
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
As mentioned before, if your line slows down quickly on a cast, those coils coming off the spool will catch up to each other and tangle up. By simply pointing your rod tip straight out after you cast and before your lure hits the water, you are helping to reduce the friction of the line on the guides of the rod.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Ladyfish fishing pole by shakespeare
ANSWER : Try switching sides of the handle by holding the bell and reeling then screw it in on the other side of the real by just reeling in.
If that doesn’t work then take all the line out and reel in some new line the opposite way.
If that doesn’t work then take all the line out and reel in some new line the opposite way.
Read Full Q/A … : Shakespeare
How to thread a Shakespeare fishing rod and reel
ANSWER : Feed the line down through the eyelets on your pole ,now open the bail on your reel tie the line on the spool,and start reeling(keep tension on the line,prevents line from tangling) when i resting mine I only go about two thirds on my spool.
Read Full Q/A … : Shakespeare
Need a Popeil Pocket fisherman manual
ANSWER : For the original pocket fisherman. I believe the design has not changed. Once you do it the first time it is actually quite easy.Two things to note. Read this whole thing first.1) the location of the bail spring (Keeps the metal bail cover up so line does not get stuck when casting.Note: This is important cause the metal bail cover must rise enough so that the line casts smoothly. (A complaint about this product. But when calibrated correctly it is quite good for what it is)2) The little **** that the crank gear plastic housing will fit into (Must be on top when you put the whole bail back in. The crank shaft lip fits into that ****.You’ll get it when you see it.Remove the panel screws (2) as you did. Pop out the crank shaft (copper). **** is in top when replacing. (remember that). Remove the bail. On the top of the bail there is a screw. ( becareful and remember how the little metal bail spring in situated here. Turn upside down with metal bail cover in your palm as it conects to the bail spring). Pull off metal bail cover. The plastic line holder actually comes apart and holds a lot more line than you think. Replace line. Feed the line back up the rod. Assemble the opposite.
Read Full Q/A … : Shakespeare
My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.
Read Full Q/A … : Shakespeare
HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).
There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.
Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?
Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.
I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.
Thanks for listening!
ANSWER : Have you been able to find a solution to this problem. I am having the same issue.
Read Full Q/A … : Shakespeare
Think it may be a line tension problem. every
ANSWER : Try attaching the swivel to a chain link fence and walk away feeding the line completely out. Then begin reeling in the line at a normal pace with the drag set at max, after 10-15 turns decrease the drag a full turn. continue doing this until the line is fully retrieved. then set the drag as you normally would before fishing. Sometimes the line gets twisted while fishing which cause the tangles and backlashes. Make sure you use a barrel swivel also.
Read Full Q/A … : Shakespeare
Shakespeare 2660 coarse fishing reel,cant remove spool cover
ANSWER : According to the intructions and I quote “Take off the cowling that covers the spool, twist off the pick up mechanism clockwise and a half turn anti clockwise will remove the spool”
Read Full Q/A … : Shakespeare
