Shakespeare

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

A good fishing reel with fluid motion would have at least four or five ball bearings as a general rule. However, more isn`t always better since the quality and material of the ball bearings also play a part in the operation.
Now, you can reorder, trim, or delete an individual clip in your Reel. 6. Tap on the Reorder button. Then, touch and hold the clip that you want to move and drag it to its new position.
In the end, the more bearings a fishing reel has the smoother it will be. As long as the bearing are in the right place, and they are good quality ball bearings, the answer is buy a spinning reel with as many bearings as you can afford.
The general rule is a full race minus one ball. But if the race holds, say, 20.5 balls (ie, has space for more than 1/2 additional ball but not a full additional ball) then you can use as many as will fit (without forcing).
To find the outer diameter of a bearing, you`ll need to measure from one side of the outer ring to the other. To measure the outer diameter of a bearing, place the jaws of your vernier caliper around the outside of the bearing and close it until it meets the outer edge of the bearing.
Monofilament is the best line choice for trolling in most situations, but there are times when low stretch lines have the edge. Because low stretch lines are super thin, they enable trolling lures like crankbaits to pick up significantly more depth compared to monofilament lines of the same break strength.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

ANSWER : Have you been able to find a solution to this problem. I am having the same issue.

Read Full Q/A … : Shakespeare

Missing left side saftey and attachment screw
ANSWER : Try Numrich gun parts america. They have parts for virtually any firearm you can find. Type in Numrich into the web. Allan 393

Read Full Q/A … : Shakespeare

Shakespeare 2660 coarse fishing reel,cant remove spool cover
ANSWER : According to the intructions and I quote “Take off the cowling that covers the spool, twist off the pick up mechanism clockwise and a half turn anti clockwise will remove the spool”

Read Full Q/A … : Shakespeare

Shakespeare fishing reel schematics
ANSWER : Try online at www.reelschematics.com they should be able to give you help.regards barry.

Read Full Q/A … : Shakespeare

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Read Full Q/A … : Shakespeare

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.
ANSWER : You can contact the Remington directly who will ship you a free users manual. Here is the company’s Contact Us details:

http://www.remington.com/pages/our-company/our-company/company-info.aspx

You may also find the required answer in the official help center. It covers almost every fields. Here is the link:

http://remington.custhelp.com/

Read Full Q/A … : Shakespeare

I have the penn Senator 15L and lately the reel when over 200 yards of Line goes out then I start to reel it in the reel starts to Slip and no line can be reeled in? Do you have a solution? Thanks
ANSWER : The weight of that much line is caausing the drag to slip. you need to tighten the drag up some more. hope this helps

Read Full Q/A … : Shakespeare