I just bought a Remington Model 742 Woodsmaster 30-06 at a large gunshow and noticed later that the bolt handle is only about 1/4 of an inch lo…

I bought a new mossberg 590 a1 shot gun a month ago, I love the gun but its having a couple of problems, the first problem is that when shooting every once in a while i get sprayed in the face with exuast from shooting through the safety very scary! any ideas whats causing this? how to fix it? second is that some times the fireing pin sticks and the gun will not discharge a round? the third problem is that i have had feeding issues with gun where it will not realice a gound from the tube, ive taken a tip of a knife to the stuck round in the tube and it prys out with little effort, these problems dont happen every time i go shooting, just every once in a while, but they a happening more and more, im conserned cause the gun is brand new, and i wanna be safe while shooting, can you guys help me? any ideas/solutions? please help!!!!!!!

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.

I have a tippmann custom pro with a cyclone feeder. I recently got the SAW stock to put on it and encountered some problems many times after I reassembled the gun. I took it apart at least 5 times before I thought it was fixed but now ive encountered another problem. I believe it has to do with the cyclone feeder not responding or something is out of line in the gun. When I picked up the gun to shoot, no paint came out so I took off the CO2 and the barrel and saw that the paintball was 1/3 inside the gun. I also have a problem when im shooting it sometimes does really fast burst. Thank you

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.

Need the wire diagram to rewire my Ariens lawnmover to bypass the safety switch. It is Ariens GT-19 model # 931026 Serial # 001463.
Can you help? It is an old Ariens mower but still runs good but now I need to bypass the safety switch in order to run it any longer. The local Ariens dealer said I need to go through the internet and get the wire diagram as they cannot give it to me directly. They told me I needed the wire diagram and the part involved in bypassing the safety switch. Hope this is all the information you need to help me.

Thank you. Roger Fielitz

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.

On my model 770 in 300 mag. new right out of the box, cleaned in and oiled it but the bolt action was still sticky and after firing a box and a half though it it still will not eject the spent casing and I have to turn the gun on it’s side and let it drop out on it’s own. I have even called Remington’s repair shop in Or. and they can’t guarantee it will work as he said it was nothing but a cheap rifle from Remington. I will be sending to Remington’s repair shop and if they can not repair it what rights do I have to get my money back? As I don’t feel that I should keep on having to pay for shipping all the time for there poorly made rifle.