o I do to fix these issues?
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Take drag knob off and make sure it starts on straight.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

The drag clicker is a little piece inside of the spool that actually makes the noise. It has a spring that makes it pop back into place and keep clicking. If the spring is broken or worn out, or the piece is missing entirely, then the clicker won`t be making any noise.
After a fish settles down, then you can tighten the drag and fight him off the reel. The other option is to pull your drag on a scale. A good rule of thumb is to set your drag at 1/3 the breaking strength of the tippet you are using for the strike or hook set, and then 1/2 and 2/3 for the fight.
You want to set the drag on a fishing reel before your first cast of the day. Adjusting it while fighting a fish can be difficult. Also, drag fishing gear is generally not designed to be adjusted while fishing, so doing so could cause damage.
According to traditional theory, drags should be set to between one quarter and one third of the line`s rated breaking strength.
If your spool tension knob isn`t working properly and you have cleaned it out but the problem is still present, then you may have dirt or debris lodged inside of the mechanism or it could lack lubrication. In this case, you will need to take your reel apart and clean it manually using a Q-tip dipped in rubbing alcohol.
Puff Reset – Press & Hold Fire & Down Button. Change between Smart Mode & RBA – 3 Clicks Fire Button.
So how much drag is enough for your style of fishing? For sailfishing, it might be just 6 pounds at strike and 12 pounds max, says Littau. For bottomfishing, it`s maybe 12 pounds at strike and 20 pounds max. Most anglers don`t ever need to go above 25 to 30 pounds of drag, says Rice.
Tightening the drag makes it harder for the fish to run and take line, while having a loose drag makes it easier. If the drag is set to loose, line will easily spool off the reel, and fighting the fish is inefficient. When the drag is set too tight, the line can`t go out fast enough, resulting in breaking off.
The most common reel on the market has a 6.4:1 gear ratio. This will allow you to work both fast moving presentations as well as slow. However, for certain techniques and applications, a very high or low gear ratio will often work best. For instance, burning a spinnerbait or buzzbait is best done with a 7.1:1 reel.
The consensus is that a reel`s drag should be set at 20% to 30% of the lines strength rating.
Drag is an essential part of fishing, as it helps reduce wear and tear on fishing reels while also providing more control over larger or heavier fish. With so many different types of drag available, it can be hard to know which one will work best in your particular situation.
While operating on the TC mode, you can adjust the wattage by pressing the button four times While vaping on custom mode, you can adjust the wattage and temperature by clicking four times By clicking the fire and + button will lock the device but it can still fire up If you need to change the screen orientation, press …
Well, the `tension` feature is a knob which can be adjusted to increase or decrease the force needed to tilt. So, a tension tilt feature essentially allows you to decide how much you want to recline on a chair, and how much force is needed to do so.
The Tension Knob controls the tension. Having a strong, tight tension pulls the spun yarn in with more power than if the tension was loose. If the tension is loose, then it will not pull in. One uses a tighter tension for thicker yarns, while a looser tension for thin yarns.
The most common reason your VOOPOO DRAG X is not firing when you push the button is because it is locked. Your device can be locked and unlocked by simply clicking the fire button five times quickly. The VOOPOO DRAG X is shipped in a locked position to prevent accidentally turning on during shipment.
Practicing casting well beyond your target and using finger-spool control will improve your accuracy immensely. When fishing topwater poppers and walkers, the occasional pause and following retrieve often stacks line on the reel loose and in an inconsistent manner.
From experiments in both research (Cogotti 1983) and development (Mercker et al 1991) it can be concluded that wheels and wheel wells contribute approximately half the drag of a low-drag car (1). Wheels and wheelhouses account for approximately 25% of passenger car aerodynamic drag (Figure1) (2).
Drag is a gender-bending art form in which a person dresses in clothing and makeup meant to exaggerate a specific gender identity, usually of the opposite sex. While drag`s main purpose has been for drag performance and entertainment, it is also used as self-expression and a celebration of LGBTQ+ pride.
The drag pressure on your reel should never exceed two-thirds the breaking strength of your tippet. It`s easy to get caught up thinking that more is better when it comes to drag. But in many ways, your drag is only as strong as the weakest link in your system, which in most cases, is your tippet.
Gear Ratio:

A 7:7:1 gear ratio is perfect for this. It can reel quickly, and it won`t start skipping smaller fish across the surface. However, you will want at least 30 pounds of drag to ensure you can handle the bass you hook into.

Moderate action rating is ideals for casting lures because it sacrifices sensitivity for improved casting distance.
Your drag should be set at 25 percent of the breaking strength (pound test) of the line you are using. You can check the breaking strength by tying the line to the scale hook, holding your rod at a 45-degree angle and pulling down on the scale.
Tighten the drag on your spinning wheel by turning the front drag adjustment button a few clicks to the right if the line pulls out too easily. If it`s too tight, loosen the drag by turning the crank a few clicks to the left. Closed face spincast models usually have a top set roller drag adjustment mechanism.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

ANSWER : Have you been able to find a solution to this problem. I am having the same issue.

Read Full Q/A … : Sport & Outdoor – Others

I bought a new mossberg 590 a1 shot gun a month ago, I love the gun but its having a couple of problems, the first problem is that when shooting every once in a while i get sprayed in the face with exuast from shooting through the safety very scary! any ideas whats causing this? how to fix it? second is that some times the fireing pin sticks and the gun will not discharge a round? the third problem is that i have had feeding issues with gun where it will not realice a gound from the tube, ive taken a tip of a knife to the stuck round in the tube and it prys out with little effort, these problems dont happen every time i go shooting, just every once in a while, but they a happening more and more, im conserned cause the gun is brand new, and i wanna be safe while shooting, can you guys help me? any ideas/solutions? please help!!!!!!!
ANSWER : Personally, with that many problems, I’d call Mossberg and get a return authorization. None of these things should be happening, especially with a new gun.

Read Full Q/A … : Sport & Outdoor – Others

Cannot open Shakespeare Synergy Steele 2001s fishing reel
ANSWER : Alright man……i had the same problem. it just takes a little bit of elbow grease, bot it does twist open, it’s just harder than hell to get it to twist off. I took a towel and laid it over the reel, and lightly tapped on it with a hammer to loosen it up a bit.

Read Full Q/A … : Sport & Outdoor – Others

Quantum Tour Edition 1170PT baitcasting fishing reel
ANSWER : Tighten the drag star to expose the black ratch ring. Press the ratchet ring down towards the star drag as you turn the handle backwards to unscrew it from the crank shaft.

Read Full Q/A … : Sport & Outdoor – Others

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Read Full Q/A … : Sport & Outdoor – Others

I have a gun safe that is open the dial will not turn and the handle will not turn either. The safe door is open but I cannot get dial or handle to turn so that I can lock door. What can I do so that I can lock door to secure my guns?
ANSWER : Well the good news is that the door is open and not locked closed — do not close the door until the problem is for sure fixed. on the inside of the door there should be a access panel that is held on by some screws,, remove the screws and panel. now depending on the make and model of the safe there are a few things that could have happened here. there is a chance that a re-locker has failed and jammed the linkages from moving. ( NOTE : the dial should not turn until the handle is in the locked position ). now if you look at the bolt linkages ( top,bottom,and sides ) make sure that none of the bolts have jammed up against the exit holes of the metal of the door. lubricate all linkages using a silicone or teflon based lubricant. the next thing to check is to make sure that the bolt from the combo pack is not broken and jamming up the handle linkage. there are not many things that can go wrong with the safe — it is all just a bunch of levers and linkages and it has been my experience ( working as a locksmith for 18 years ) that this problem is a binding issue. again,, I cannot stress it enough to make sure you do not close the door until the issue is fixed and you have tried the combo several times and simulated a open and close ( handle lock and un-lock ) test.
if after all this you are still having issues – it is well worth the service call to have a locksmith stop by and service the safe, this will insure that the safe does not lock you out.

c…

Read Full Q/A … : Sport & Outdoor – Others

Shakespeare 2660 coarse fishing reel,cant remove spool cover
ANSWER : According to the intructions and I quote “Take off the cowling that covers the spool, twist off the pick up mechanism clockwise and a half turn anti clockwise will remove the spool”

Read Full Q/A … : Sport & Outdoor – Others