torage.When i recently got room for it and want to use it again there a big problem i can’t rember the combition it’s a dial combition and a handle you pull up or down on to open the door all the way after u do your dial combition. HERE is my serial number hope that will help pleas help me SERIAL# 2037303 GRANITE SAFE (RED HEAD)
THE DIAL TURNER WITH NUMBERS SAYS SARGENT@GREENLEAF IN THE CENTER OF THE DIAL
Stack On 16 Gun Safe with Combination Lock
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
Read through your safe data and check how long the lockout code will release. Some safes will release after 20 minutes, while some will release after 30 minutes.
Gun rust is a big problem for those who store their firearms in gun safes. In fact, corrosion tends to happen at a higher rate and more rapidly in a gun safe than out of it. The reason has to do with basic chemistry.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
The first day of diving went fine. However, as the week progressed I noticed that when taking in a breath the regulator continued to trickle air at a very small rate. While not enough to be concerned about safety at this point it has become an annoyance both from the fact that bubbles continue to trickle past my ears and air usage has increased. This is an intermittent problem.
I had it looked at by 2 certified Scuba Pro Dive shops and they could not find anything wrong with it though one did lower the first stage pressure just to a bit to see if that would work. I also cycled the control lever position for “dive” and “surface” intervals to ensure that there were no sticking problems.
It does appear that the problem is intermittent and that it only occurs when the regulator is under water.
In addition is there a diagram in which I can use to troubleshoot this problem?
NOTE: this version of the X650 was not on the recall list of Scuba Pro.
Any help would be appreciated.
if after all this you are still having issues – it is well worth the service call to have a locksmith stop by and service the safe, this will insure that the safe does not lock you out.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).
There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.
Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?
Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.
I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.
Thanks for listening!