:00 p.m. I cannot find the directions that came with the timer.
Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Plug the timer into the power outlet, the LED marked with power will light up. The LED marked on will light up when power to the outlets is on. Note: This item is a photoelectric device and contains a light-sensitive photocell to turn on and off automatically.
The timer is very simple to operate. You plug it in and hit the button on the front to cycle through the options (which are off, on for 1-9 hours after dusk, on from dusk to dawn, or on now for 1-9 hours). The digital indicator on the front makes it easy to see at a glance what setting you`re on.
The timer pins are factory preset in the “pushed down” or “ON” position. Pull up all of the pins before pushing down pins for your desired “on” time. Note: The “pins” are grey slices around the dial. For example: to turn the timer on at 5pm and off at 10pm, push down all the pins between 5PM and 10PM.
Plug the timer into an electrical outlet and connect your light. Put the programmed timer into any free electrical socket. Plug the power cord from a lamp or other light fixture into an outlet on the timer and turn the light`s power switch on so the timer will turn it on and off at the times you programmed.
Digital timer switches are typically connected to electrical circuits powered via the mains supply. They feature timing circuitry, switching devices, and no moving parts. Such switches can be used to turn lights on or off at times selected by the user.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

We have a pop-up with the sink that folds down. We need to replace the sink drain from the sink to outside, but the only flex drain hoses that I can find have a hose only 26 inches long. I know that will not be long enough to go from the sink to the outside of the camper.

Do you know if any place I can go to get a sink drain system with a longer hose. The contraption (I don’t know what it is called) at the base of the sink drain has rusted off so that the swivel part of the drain system is gone. We currently have a garden hose connected to the pipe coming directly from the drain, but when we close the camper, it pops off.

Do you have any suggestions?

Thanks

Michele

ANSWER : Hi mj2181,I would say your problem should be solved easily with a hose extension , if you can get the extension and then use it , it should be ok for you and there should be no need to get a sink drain system with a longer hose.An example of an extension hose can be found on this link :- http://www.searspartsdirect.com/partsdirect/part-number/7174401GS/0071/580?sid=SPDx20101101xNXTGHope this helps ,

Read Full Q/A … : Sport & Outdoor – Others

Blown fuse, i think
ANSWER : Pull one fuse at a time check to see if its blown,continue until you find the blown one(hold fuses to a light to see if the wire in fuse is seperated.)

Read Full Q/A … : Sport & Outdoor – Others

Trying to install a new fluro light, pull out old light to find 3 reds and 3 blacks 1 copper earth. What do I do to connect it up the right way??? When I pulled the old Fluro light out the 3 Reds were joined together with a connector ,two blacks were joined to one end of light wire, the other to the other end of the light wire,earth wire to the light case,the third black wire was connected to the wire from the ballast? Does this all make sense
ANSWER : No, this does not make sense but I have seen strange wiring before. There is power going from the light someplace else. Just connect it back up exactly as the old light was connected. It worked before so it will work again. If it works it is wired correctly. Without being there to check which wire was the hot wire and which was neutral it is impossible for me to say what is what. Make sure you connect the ground wire to the light chassis.

Read Full Q/A … : Sport & Outdoor – Others

I have a 1997 Coleman 107 Hot Tub. While filling the tub it over flowed and the circuit breaker popped. Over the years I’ve done this a couple of times. I remove the side, let things dry for a day or so and everything is fine. This time, I reset the breaker and the spa went on. The pumps work fine, and the control panel shows the temp and the indicator light shows the heater is on. However, work never heats up. The local spa repair folks are crooks and they know less than I do, and I know NOTHING. Nonetheless, I’m going to try and fix the problem myself. Now, I need to know the best way to determine if the problem is the circuit board or the heater itself. I also need to know where I can get a repair maual. I’m tired of paying Goober and Gomer hundreds of dollars.
ANSWER : Check the terminals that lead into the heating element to ensure voltage is present (110 AC) if voltage is present upon start up the heating element must be replaced if no voltage is present is is most likely a control board issue. Go to this web site for contact info and possible repair manual aquisition.

http://www.spaguts.com/SpaHeaters.aspx

Read Full Q/A … : Sport & Outdoor – Others

My MSR Pocket Rocket will no longer light. Prior to the complete malfunction, the flame started to become much weaker, and then finally, the burner just would not light. I’ve removed the rubber o-ring on the bottom, uncovering a small hole, but am unsure as to whether this would have anything to do with gas delivery to the burner area. My guess is that there is some sort of buildup that is plugging the passageway through which gas would stream, preventing me from being able to light the burner, but am unable to locate an issue, since it appears I cannot disassemble the unit.
Do you have any suggestions?
Thank you,
Scott
ANSWER : Hi, chances are the jet is clogged – I’ve experienced this myself on the same stove.

I would leave the rubber o ring alone, the chances of the hole there being blocked are slim, it is more likely to be the outlet jet you can see throught the holes on the riser tube under the burner head.
This tube can be unscrewed – you may need to put something through like a pen for leverage. Once you have done this you can remove the tube and you will see the tiny jet in the top of the brass nut on the knurled base of the stove. Then its simply a matter of finding a thin enough wire or pricker to prod araound in the jet. I have a fine wire brush that works well, although I have only had to do it once in several years.
Put it all back together and you should be back to full power – the whole job takes two minutes tops.
The other thing I did was screw the riser tube back hand tight only – this means I can dismantle and clear the jet when camping if required. It doesnt affect performance or safety. I put a strand of the wire in a blob of blu tak in the plastic case the stove comes with – job done! Hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

I have a wildwood le 25bhbs and the only towing lights working are my signal lights. can’t get running lights or brake lights to work. I saw where it looked like the towing harness may have been pinched. So I repaired that, but, they still do not work. Any ideas? Is there a fuse somewhere I need to check? Do I need to hook the trailer up to my trailer hitch before they will work? Is there a wiring diagram or repair manual somewhere I can get? Any help would be greatly appreciated. Thank you.
ANSWER : There should be an inline fuse, check that first.

Read Full Q/A … : Sport & Outdoor – Others

Hi, my tiger river spa does not heat. Filters are clean, jets work, no light installed. On ciruit board, green light for “Lim” , red light for heat, no other lights. Just bought house one month ago, no manuals.
Spa is a Bengal. Have noticed a symbol (can’t tell what it is) on the screen then most of screen goes blank with just the power light on. Is there a vacation mode or something like that?
Thanks for your help.
ANSWER : Spa’s are such that so many components can become faulty when left unattended to over a period of time. But most likely what your unit needs is just a regular service to clean up its systems and also ensure there are no leakages in the pipes. Bengal is a wonderful and durable product.The problem could range from low power supply to wires being eaten up by rats and other pests. Also it could be burnt out heaters thereby the inability to produce heat. The indicator on the screen could mean various things but the screen going blank usually would be caused by poor power supply.If you dont have the technical know how refer an expert to check it out and ensure the exact problem of the above mentioned is wrong with it before repairs can be carried out.Hope this solution has been helpful?

Read Full Q/A … : Sport & Outdoor – Others