i could buy one i would be grateful. paul.
Reebok
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
An E6 or E7 error code is an incline error code. The E7 code means the potentiometer value the console is reading from the lift motor is out of range. This can happen when there is a bad wire harness connection or a damaged wire harness. It could also just mean the incline motor needs to be adjusted back into range.
The E-5 error code relates to a communication error between the computer and the resistance motor.
Check the drive belt for proper alignment. With the cover still off, check over the wire and cable connections, as they may have become loose or disconnected during shipping or assembly. Make sure connections are secure and no wires are crimped, damaged, disconnected or burnt.
If the E1 error occurs after the belt starts to move for several seconds, the error code means that the system is not picking up the speed of the motor. This pickup comes from a magnet mounted on the front roller pulley and a speed sensor, or a problem with the magnet.
E1 Error: Treadmill calibration did not receive a signal for greater than 10 seconds. Resolution: Check to ensure that the cables connecting the console and controller are secure. If any of the cables/connectors appear loose, completely power off and unplug the treadmill before unplugging and reattaching the cables.
E8 Error: Internal motor driver error. Resolution: Ensure that the treadmill is connected to the external power source and that the proper voltage necessary to power the treadmill is available. After confirming the treadmill`s connection and voltage from the power supply, completely power off and unplug your treadmill.
E3 Error: Inside of motor drive is overheated and the high temperature exceeds the protection level. Resolution: Check the treadmill motor for signs of overheating (strong smell, grinding noises, inconsistent operation speeds). If the motor appears overheated, ensure that the treadmill is properly lubricated.
The serial number may be located on a white or a silver decal in one of the following positions: Below the power cord on a white or a silver decal. On the right hand corner at the base of the treadmill. On the left side frame of the treadmill where the upright mounts to the bottom frame at base of treadmill.
If you have noticed that your walking belt has shifted to one side or is about to start rubbing against the side of your exercise equipment, it just needs to be adjusted. All that is required to do this is the Allen Wrench or Hex Key that came with the treadmill; this was used for and during the original assembly.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
TC5000 and after extended use I smell burning and upon removing the belt cover and drive belt I felt of the motor on the motor side of the drive pulley and it was ”red-hot”, obviously the source of the smell of the burning. The motor spins freely without any rubbing noise. The drive pulley (motor side) and the tread pulley appear to be alligned. One curious thing is that the threaded motor output shaft is recessed about 3/8” from the outside edge of the pulley. Could it be the bearing on the pulley side of the motor? I am dumbfounded as to what the solution might be. Note that I could not enter the exact product as my model seemed to be invalid. My model is the TC5000. Thanks [email protected]
ANSWER : Just because it spins freely doesnt mean it cant have a shorted winding. Id send it back where it came from or at least replace the motor.
Read Full Q/A … : Reebok
I have an 8100 ES Reebok treadmill. There is a squeaking noise coming from the drive motor. It is coming from the non-belt side (if facing the front of the treadmill, the left of the drive motor. When the treadmill is turned off, I can manually move the walking belt in the walking / running direction and it will squeak. If I move it in the opposite direction, manually it does not squeak. Also, if I need to lubricate the bearings can you tell me how to get to them to do this. The motor has plenty of power and no other problems, only squeaking. I have sprayed a belt lubricant on the belt and also blown it all out with a can of compressed air (used for computer key boards).
ANSWER : Hi.the bearings in these machines should be lubricated and sealed for life. they are not designed to be touched. it sounds like you have done the important bits. belt lubrication and blowing out any debris that may be there. squeaks like this can be incredibly difficult to find, but can also be incredibly annoying.the main things that you can do is keep watching to try and find exactly where the squeak is coming from and check for anything wrapped around the edge of the roller.keep using the belt spray, and the compessed air.a good grade silicone lubricating spray used at the edges of the rollers, by the bearings and around the motor and gearbox unit may also help but do not get this spray on the belt as it can be very slippery.squeaks like this can start and stop on their own or develop slowly and go just as slowly.keep doing the maintenance you are doing, and use the silicone spray as described above.it may take a little while for the spray to work its way into the bearings as they are fairly well sealed but you should notice an improvement after a few days.please feel free to ask for further advice if you need
Read Full Q/A … : Reebok
My daughter has a sweet pea scooter that had been blowing fuses and the motor got hot. Im sure the motor is shot. but my question is can anyone tell me if the motor would be the only thing I need to c
ANSWER : Find out whether it is 6 volts or 12 volts and there should be two wires that feed the motor either cut or splice and attach another set of wires with fuse in the line (simular to jumper cables) raise the back tire so it does not touch the ground and place jump wires to the negative and positive of the battery.If the motor moves in either direction without blowing the fuse the motor is good if not then its bad. Uses the same amperage fuse
Read Full Q/A … : Reebok
Recently, I was using my Horizon CST 4.5 treadmill when the power on the treadmill and the room it was housed in went out. I reset the cicuit breaker and tried to get back on the treadmill. It turned back on, counted down from 3, and the time began however the running surface(track) would not move. I lifted the front end where the motor and belts are housed. I noticed that the belt was still intact. Unsure if motor is burnt out. Any help would be appreciated.
ANSWER : There is usually a small breaker on treadmills that pops out and you have to push it in to reset it. Take a look around the front of the treadmill and see if you can locate the breaker and reset it and the treadmill should work normally.
Read Full Q/A … : Reebok
I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.
Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.
Read Full Q/A … : Reebok
Reebok elliptical trainer belt replacement
ANSWER : Ask here for instructions how to change, they can get you any Reebok manual
Read Full Q/A … : Reebok
I-run treadmill belt does not run
ANSWER : Maybe check the troubleshooting section of your manual. If you don t have one, check here.
Read Full Q/A … : Reebok
