I have a Moultrie I40 digital game camera. It was working OK until the last time I took the SD card out. When i put the card back in the messa…

I am using a Fujifilm xD-Picture card H512mb in my Fujifilm s5500 camera. I’ve used this same card before in the same camera, but thother day took the card out and downloaded its photos direct on my laptop. I now find that on re-inserting the card in the camera , the camera screen say “card not initialised” and it won’t work. How do I remedy this, please?

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.

See less

Ok, so last week one of my airsoft guns, the Crosman Stinger R39, and part of the cocking mechanism broke to where it can not be pulled back, and the Airsoft pellet cannot be loaded into the chamber. so I took it apart, to get the other half of the cocking mechanism. I then proceeded to fix it (with gorilla apoxy) and let it dry until today. a little while ago, I put it back together, tried to **** it back, and – SNAP – it broke….. again. is there a place to buy replacement parts replacement parts for it?

I have a treadmill Nautilus 516, I mark an error e7 flashing. I already unplugged, lubricated, and clean the speed sensor with alcohol and a clean head cotton. When I jump in at the front it locked out like when you put it in position for move it. When I put start in 4 seconds get the error e7; and when the error still the jump in the front and locked if I put in the back of the walking part do not locked out but still get the e7.

Slide out quit working and fuse on battery blows everytime I chan

Hey guys So today i bought a Fujifilm Finepix S1700 to get me started, and i powered up with my 8GB SD-HC memory card inserted which is formatted, and I came across the message “card Error” so i went into the menu and found set up and tried to format it throughh the camera. It displayed the message ” PROTECTED CARD” Can anybody give me some help please?