I have a Hotub; an Emerald Spa Model 595C SS-3D. The heater is working somewhat but does not reach the set temperature on the digital pad. I am…

I have a 1997 Coleman 107 Hot Tub. While filling the tub it over flowed and the circuit breaker popped. Over the years I’ve done this a couple of times. I remove the side, let things dry for a day or so and everything is fine. This time, I reset the breaker and the spa went on. The pumps work fine, and the control panel shows the temp and the indicator light shows the heater is on. However, work never heats up. The local spa repair folks are crooks and they know less than I do, and I know NOTHING. Nonetheless, I’m going to try and fix the problem myself. Now, I need to know the best way to determine if the problem is the circuit board or the heater itself. I also need to know where I can get a repair maual. I’m tired of paying Goober and Gomer hundreds of dollars.

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.

The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.

Problem with anti-reverse

I am trying to get the pictures from my camera finepix j210

I have a multifunction sports watch that i bought from Big W, (no brand name)

By accident i set the watch to 24 hour time, originally it was set to 12 hour time, how do i set it back? ive tried every button combo including the button combo i used when i accidently set it on 24 hour time, the instructions only say how to set the time and date, it doesnt say how to toggle between 12 hour and 24 hour time, is there a generic way to toggle it on sparts watches? btw, holding the mode button in does nothing on my watch, no matter how long i hold it in for

My pool filtering system has been installed for 5 years and has worked well. It has a Jacuzzi 1.5hp pump and a Hayward s244t filter with heater and a salt generator. I have never replaced the sand. It has had a problem 2 times in the past week at startup in the morning. It appears there is blockage in the filter preventing flow through it because when I open the pump backet, it is pressurized. If I then backflush or rinse the filter, everything appears to work fine. Then I switch it back to normal filter operation and it works ok. I have a timer on the filter and the problem only occurs first in the morning when the timer starts it. Any ideas?