I have a bushnell rangefinder bought in 1996 #200400-085374 n cannot get it to read over 150 yrds we put new batteries in it and i dont know wh…

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

A short that drains the battery

How to insert battery. I have a 2 year old watch I have never used. I cannot get it to start so I presume the battery is dead. When I open the cover I find battery has a thin metal strip over it and cannot figure how to open it to get the battery out

I have a 1997 motor guide wireless 24volt Big Water trolling motor. hooked it up to the batteries and put in a new 9volt battery in the foot pedal. the lights come on on top of the motor head and the foot pedal beeps, but the prop doesnt turn or spin (like there is no power to the bottom of the motor) any suggestions to what the problem is or how to fix it? (just bought the motor from a lady who’s husband died. dont have any manuals)

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.

Spark plug wire boot grounding out on coil, 96 outback 2.5 automatic, just put new spark plug wires, new spark plugs, and new coil on. ran great for two weeks, now spark is jumping out of boot at coil on one wire, put old coil back on and still does it in the same spot. replaced wires again, and still does it in the same spot. seems to do it only under a load. Is my new spark plug on that cylinder bad? Does the coil need some insulation under it? It is the coil that sits right on top of the motor. Any ideas? thanks.

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.