Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Re: Baitcaster spinning backwards

Sounds like either its going bad or you got too much oil on it. I have noticed cold weather can also cause the AR bearing to slip more. Try cleaning it and if that doesn`t work, it may need replacing.

To change reel handle side back, so that you are casting with your right-hand and reeling with your left, you simply change the steps to the opposite side. Unscrew the dust cap on the left side of the spinning reel until it comes out.
If you don`t want to share the video to your feed, tap on the slider for that option so it will only upload to your Reels tab. If you`re not ready to share the post publicly but want to save it for later, tap the Save as Draft option at the bottom of the screen. This will save the video file as-is.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Muzzleloader catastrophy!! I need HELP!!
ANSWER : Try pliers

Read Full Q/A … : Sport & Outdoor – Others

Ladyfish fishing pole by shakespeare
ANSWER : Try switching sides of the handle by holding the bell and reeling then screw it in on the other side of the real by just reeling in.
If that doesn’t work then take all the line out and reel in some new line the opposite way.

Read Full Q/A … : Sport & Outdoor – Others

Problem with anti-reverse
ANSWER : If it is a multiplier reel most of the lever tension springs are the same. they can be bought from QUENTIN MILLMAN in portsmouth. they have a mail order branch and can be located on line.i have tried making my own springs but the dog leg has to be at the right angle.best buy the right one for a few pounds. regards barry.

Read Full Q/A … : Sport & Outdoor – Others

How to I fix a spin casting reel?
ANSWER : You should be able to remove the spool by removing the knob on the front of the reel which also is the drag adjustment. With the knob off the spool should pull right off. Hope this helps you

Read Full Q/A … : Sport & Outdoor – Others

AB LOUNGE 2….I need the 2 bars that hold the front part of the legs to the back part of the legs of the ab lounger together. How can I obtain these 2 parts? Please does anyone know?????
ANSWER : Fitness Quest Customer Support: 800-321-9236http://www.bestdirect.tv/downloads/AB2.pdf Good luck.

Read Full Q/A … : Sport & Outdoor – Others

Putting my airgun back together
ANSWER : Http://www.flickr.com/photos/wrenchmonkey2k/

Read Full Q/A … : Sport & Outdoor – Others

I own a tippman a5 with an UMP shroud and fake metal clip. I took apart for some maintinance and ever since i put it back together its been acting like im out of air after 2-3 quick shots. I took it apart to check it and everything was ok. So i screwed the tank back in and now i have a small leek on tthe nutin between and the tombstone.

What do you think the problem is (im afraid their two different problems).

ANSWER : There is an O-ring up in where the Tombstone slides in. That O-ring has to be lubed (oiled)
and should be toward the rear of the gun when installing the Tombstone. Also, drop-off
in firing can be caused by lack of lube on the internal O-rings. 2 drops of oil in the inlet hole
where your bottle screws on and then dry firing to cycle the oil thru might help. You may need
to completely tear down the gun and clean and lube the internal O-rings. If you can switch to
air AKA…HPA (High Pressure Air) it will be better for internal parts and better consistency overall.
Here is your manual for reference.
http://www.tippmann.com/pdfs/products/A5/a5manual.pdf

Read Full Q/A … : Sport & Outdoor – Others