it was only down a gallon? Took it home, lit it up and a few hours later it went off again? I’ve had the same prooblem with three different tanks. any ideas?
Sport & Outdoor – Others
Experienced athletes share their insights in answering this question:
Tank regulator is probably freezing up if your tank is in the cold, which I’m assuming it is, otherwise why would you have heater on. How cold is it, where you and tank are? Pouring warm water over the regulator area, will usually thaw that when it happens, if it is convenient to do so, without making a mess. Tank filled too full can be a contributing factor as well. That heater probably takes a lot of volume to run, and as propane escapes tank, it causes tank to get colder, thus valve freezes up. One way to eliminate that, would be to see if filler can remove any moisture in tank, by injection methyl hydrate, or similar to remove any moisture in tank, which by the way, should have been done first fill and purge of the tank. Make sure they know what they are doing that’s all. Other option, to cut down on volume coming out of one tank would be to add another tank, with “T” in line to both tanks, and have it draw from both tanks at same time, thus it should overcome excessive flow and freezing of one tank. Check at local propane distributor, as well, they may have an easier solution, but if not, they will have what you need to add second tank.
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
The typical cause for this is that the pilot light flame has become too far away from the thermocouple. Thus, the thermocouple will turn off the patio heater as it tricks the gas value in to thinking that the pilot light is out.
If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.
Answer: A standard 20lb. propane cylinder will provide anywhere from 9 to 15 hours of heat depending on which heat setting you use.
Electrical overload: If an electrical component inside the heater is overloaded, it could trigger the circuit breaker, cutting off power to the entire unit. If you have to keep resetting the breakers in order to make the heater function, this is likely the problem.
If your furnace shuts off after a few minutes and starts more than eight times an hour, it may require repair. Common causes of furnace short cycling include restricted airflow, a malfunctioning flame sensor, or a poorly placed thermostat.
The problem lies with the bypass valve inside the regulator. If there is excess pressure, the valve will get fully or partially stuck to stop gas from exiting the tank. Luckily, all you need to do is reset the bypass valve.
The most common patio heaters produce roughly 40,000 BTUs per hour – meaning a 20-pound propane tank will provide upwards of 10 hours of heat on the highest setting.
A 13kg gas cylinder will typically last for 10 hours of use, after which point you`ll need to replace the cylinder. This is a fairly quick job but needs to be done when the heater is cold, to avoid burnt fingers.
If the pilot flame ignites but goes out after you release the gas control knob, the cause may be a dirty or defective thermocouple. If the gas is on but the flame will not ignite at all, a pilot tube obstruction is the most likely issue.
If your furnace shuts down after a few minutes, it`s likely due to a faulty or unhygienic flame sensor. This crucial component intends to monitor the gas burner. Also, when a flame sensor cannot detect the burner, the furnace runs for a few moments before shutting down and restarting.
Newer heaters typically have built-in safety features like tip-over protection and automatic shut-off to guard against overheating, which can help prevent the risk of residential fires.
Clogged air filters are one of the most common problems for heaters. If your heater cannot blow anything or at least fails to let out hot air, the chances are that your filter is clogged. Filters naturally become clogged as debris builds up in them.
CAUSE: The most common cause for electric heater not working is blown fuses. SOLUTION: To check this, first unplug the device and check the fuse box of the house for blown fuses as well as tripped circuit breakers.
Your Gas Valve Needs Attention
The gas valve on your furnace delivers the gas your pilot light needs to remain lit. If the valve is turned ON, but your pilot light won`t stay lit, the problem might be a broken gas valve. The solution most likely will be to replace the valve.
The thermocouple looks like a small nub, but inside the tubing, it is comprised of two different metals, usually wires. They are welded together at one end, referred to as the “hot junction,” while the other end is the “cold junction.”
Reasons your log burner keeps going out include:
Having a dirty stove or chimney. Suffering a poorly drafted chimney. Not controlling the air supply properly. Your stove being too cold.
Insufficient airflow into the furnace
For the burners to ignite, they need airflow. The airflow into the furnace comes from the blower fan that draws air through the return air ducts. But if this airflow is choked off because of a clogged furnace filter or faulty blower, the burners may not be able to stay on for long.
Store spare propane tanks away from heat or open flames. Protecting Your Patio Heater Against the Elements. Most patio heaters have some weather-resistant coating, but wind is your patio heater`s worst enemy. Especially prone to wind are domed heaters, acting as umbrellas and catching wind.
Patio heaters are outdoor products. However, leaving the heater exposed to the elements when not in use may accelerate deterioration of the finish and working parts over time.
A 15kg cylinder will last around 50 hours. Disclaimer: calculations are estimates not guarantees.
The average portable propane patio heater houses a 20lb propane tank or about 4.7 gallons of fuel. A 20lb propane tank can last up to 10 hours and costs between $15 – $20 to fill up, making the average cost per hour between $1.5 – $2. A typical 40,000 BTU patio heater will cost about $1.70 per hour to use.
Although it may be smaller in size, the 5kg Patio gas bottle is big on cooking. It will provide up to 14 BBQ sessions based on a 3 burner BBQ with side-burner, operating at full power for 30 minutes each time.
If you use a gas cylinder to cook for four people, you use around 70 g per hour. A 12.5 kg butane cylinder will therefore last around half a year. If you only use the cylinder for barbecues, the cylinder may last for up to four years.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.
Read Full Q/A … : Sport & Outdoor – Others
I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.
Read Full Q/A … : Sport & Outdoor – Others
I have a 99 yamaha f100 four stroke outboard. Problem I have is boat will acclereate fine get up on plane and after running for about a mob at wot will decell and only run around 4500 rpm. Then after coming back to idle will have a slight miss then run smooth and repeat every run. Changed the plugs and fuel filters alll oe yamaha has fresh oil timing belt is good any ideas will help or fuel psi spec. I am an ase master automotive tech so I know alot about engs. To me it feels like it’s running out of gas. Like the carb bows are full when I take off but then runs out after running wot. Any info will help
ANSWER : I have exactly the same problem with my Yamaha F100, have you got any solutions yet?
Read Full Q/A … : Sport & Outdoor – Others
2008 Yamaha vx deluxe will only run about 30 mph
ANSWER : If the motor is reaching full revs look at the jet assemby for fouling or prop damage. If it is not reaching full revs get authorised mechanic to fix it, it will be cheaper in the long run.
Read Full Q/A … : Sport & Outdoor – Others
Pop-up camper lights all turn on when tow-vehicle lights are on
ANSWER : FIRST, make sure white wire of camper is grounded to the frame of tow-vehicle. Temporarily use a jumper-cable frame-to-frame. Then apply 12volts individually to each of the three circuits to the camper. Assuming a 4-wire flat connector — brown wire is for marker lamps; yellow is left brake/turn; green is right brake/turn
Read Full Q/A … : Sport & Outdoor – Others
Saltwater filter system on an INTEX swimming pool.
After putting fresh well water in pool, (5,060 gallons) I put in 120 lbs. of swimming pool salt. I ran the filter for 24 hours then fired up the saltwater chlorinator. After an hour the water went from totally clear to clear but now quite green. Now what? There is still about 1 hour to go on the recommended 5 hour cycle. It’s not clearing up.
Tony
After putting fresh well water in pool, (5,060 gallons) I put in 120 lbs. of swimming pool salt. I ran the filter for 24 hours then fired up the saltwater chlorinator. After an hour the water went from totally clear to clear but now quite green. Now what? There is still about 1 hour to go on the recommended 5 hour cycle. It’s not clearing up.
Tony
ANSWER : Are the require hours properly set as required.In some cases it takes much time in clearing/cleaning the dirt from water.
Set the operating hours using the up arrow button to increase the hours of operation and the down arrow button to decrease the hours of operation. Hours of operation are determined by the amount of water in gallons for the pool size.Re-lock the keypad by pressing and holding the down arrow button for 2 seconds until a long beep is heard, then pressing and holding the up arrow button for another 2 seconds until a second long beep is heard. The green LED light will light up within minutes indicating the system is operating.
It is possible to run the system for a longer period of time than is necessary. However, because chlorine dissipates over time (which is why pool owners must constantly go to the store, constantly purchase, and continually add standard chlorine to their pools), if you happen to run your Saltwater Pool System too long, you can simply begin running it for a shorter period the next day, and your pool will be fine. The best way to determine the optimal length of time to operate your system is to experiment with different operating lengths of time, and to test the amount of chlorine in your pool using the chlorine test strips provided by Intex. See Owner’s Manual for operating time table list. If you have one available.
How long does it take for the Saltwater Pool System to clear the “green” water from my pool? The Intex Saltwater Pool Systems work very quickly, and will immediately begin eliminating bacteria and algae from pool water. However, the exact amount of time needed to transform dirty, dangerous pool water to safe, clean, clear, fresh pool water will depend on a number of factors including how dirty the pool water is to start with, the size of the pool, and the temperature of the outside air.
Will the Saltwater Pool System work even if I use well water? What if I have hard water? Yes, the Saltwater Pool System will work in all water conditions. However, you may find it desirable to treat your water (just as you would if it was being used in your house), if it is hard or has high levels of calcium, etc. Calcium can form white scale on the titanium plates in the electrolytic cell, thus requiring more frequent cleaning. Other than more frequent cleaning, it will not affect the ability of your Saltwater Pool System to perform its functions.
click this link below for more troubleshooting:–
http://www.intexstore.com/FAQSaltwaterSystems-General.aspx#12
Thanks. keep updated for any more query.you can rate this solutionand show your appreciation.
Set the operating hours using the up arrow button to increase the hours of operation and the down arrow button to decrease the hours of operation. Hours of operation are determined by the amount of water in gallons for the pool size.Re-lock the keypad by pressing and holding the down arrow button for 2 seconds until a long beep is heard, then pressing and holding the up arrow button for another 2 seconds until a second long beep is heard. The green LED light will light up within minutes indicating the system is operating.
It is possible to run the system for a longer period of time than is necessary. However, because chlorine dissipates over time (which is why pool owners must constantly go to the store, constantly purchase, and continually add standard chlorine to their pools), if you happen to run your Saltwater Pool System too long, you can simply begin running it for a shorter period the next day, and your pool will be fine. The best way to determine the optimal length of time to operate your system is to experiment with different operating lengths of time, and to test the amount of chlorine in your pool using the chlorine test strips provided by Intex. See Owner’s Manual for operating time table list. If you have one available.
How long does it take for the Saltwater Pool System to clear the “green” water from my pool? The Intex Saltwater Pool Systems work very quickly, and will immediately begin eliminating bacteria and algae from pool water. However, the exact amount of time needed to transform dirty, dangerous pool water to safe, clean, clear, fresh pool water will depend on a number of factors including how dirty the pool water is to start with, the size of the pool, and the temperature of the outside air.
Will the Saltwater Pool System work even if I use well water? What if I have hard water? Yes, the Saltwater Pool System will work in all water conditions. However, you may find it desirable to treat your water (just as you would if it was being used in your house), if it is hard or has high levels of calcium, etc. Calcium can form white scale on the titanium plates in the electrolytic cell, thus requiring more frequent cleaning. Other than more frequent cleaning, it will not affect the ability of your Saltwater Pool System to perform its functions.
click this link below for more troubleshooting:–
http://www.intexstore.com/FAQSaltwaterSystems-General.aspx#12
Thanks. keep updated for any more query.you can rate this solutionand show your appreciation.
Read Full Q/A … : Sport & Outdoor – Others
My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.
Read Full Q/A … : Sport & Outdoor – Others
