ger belt cause this to happen?
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Its possable,one inch longer belt withouta belt adjustment is a huge amount of slack.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Your riding mower belt keeps coming off because of several possible causes such as a damaged, dirty, or incorrectly installed belt. This problem can also be due to an oil leak, damaged mower pulleys, damaged bearings, or a misaligned or stretched out belt.
A perfectly tight mower belt can rotate without slipping off but not cause the engine to over-exert and overheat. If the belt does not slip off while working and is not producing unfavorable sounds that indicate wearing off of the belt, then that is the perfect tightness for it.
For most effective results, a lawn mower deck should have a pitch, or height difference of 1/8-inch to 1/2-inch between the front of the deck to the back of the deck. Naturally, this makes the sweet spot about 1/4-inch of pitch, depending on the mower model.
The signs of a loose mower deck belt include the mower belt slipping, the belt coming off the pulleys, a stretched belt, excessive vibration of the deck belt, a high pitched noise, rapid signs of wear and tear, and a shiny and glazed belt, among others.
The short answer is the belt is molding to your body style. Belts will mold and form to your body much like a pair of leather shoes will. Each person will have varying degrees of curving on the belt based on their body size, weight, and how they wear their pants.
Improper Tension of V-Belts

If a belt is not tensioned properly, it will ride too loose or too tight on the pulley. A belt that`s too loose on a pulley will cause slippage, which leads to heat build up from friction. This heat will damage your rubber belts and cause the belts to crack and break.

If a belt is too tight in a system, it can add stress to your bearings. The added stress to bearings can result into over amperage of your motor and potential motor failure.
to spend less money than you did before because you have less money: I`ve had to tighten my belt since I stopped working full-time.
To even out the tension in the belt, use a spanner or socket wrench on the crankshaft-pulley bolt and turn the crankshaft two full turns clockwise . Tighten the locking bolt first to hold the tensioner in its new position. Tighten the pivot-spring bolt, which has a precise torque setting.
Simply loosen the strap, take it off the motor, give the strap one twist, reconnect it to the motor, and tighten the belt. The belt now makes a figure-of-eight instead of a simple loop, which effectively reverses the direction of the motor.
For most effective results, a lawn mower deck should have a pitch of 1/8-inch to 1/2-inch between the height of the deck rear to the height of the deck front. Naturally, this makes the sweet spot about 1/4-inch of pitch, depending on the type of mower.
The top setting for most mowers gives a cutting height between 3.25 and 4 inches. This is best for your lawn, but at a setting of 4 inches you may sometimes see some “laying-over” of turf blades that some people find undesirable. For this reason, some people prefer to mow at 3 or 3.5 inches.
The belt has a glazed or bu​rned sidewall.

Look at the belt edge that contacts the pulleys. If it appears shiny, glazed or burned, it will need to be replaced.

If the belt is too loose or slips this could force the engine to stall or shut down. This could be very dangerous if the car is on a busy road or motorway. i The car battery is dead. If the issue is severe, the battery will not be able to maintain its charge and could die shortly after the car has been started.
If you have limited closet space, rolling your belts is a great option. The key to rolling your belts is to roll loosely, especially if they`re leather belts. If you roll the belt too tightly, the leather can bend more than you want and form creases.
Most Belts are normally measured from where the belt leather folds at the buckle end to the middle hole at the tip end and are usually stamped on the back of the belt with the size example 32, 34, 36 etc.
In general, the length should reach to just beyond the first belt loop on your pants.
A pulley is a simple machine. It changes the direction of the force applied. It is mostly used to reduce the amount effort required to pull an object.
There is no specific time length that mower belts need to be replaced. Some belts may last longer than others due to different operating conditions. One thing is for certain though, the more the mower is used, the sooner you will need to consider replacing the mower belt.
A: Your mower has two belts. Both play a role in making the blades turn. The “Deck Belt” goes around the pulleys right above the blades on the deck and then to a double pulley. The “Drive Belt” on your mower goes from the transmission, around an Idler pulley then over to the double pulley I mentioned before.
Typically, the belt strap should end between your first and second belt loop. If you have enough extra material to loop it through the second belt loop, it`s too long. If your belt doesn`t extend through the first belt loop, it`s too short.
Belt slippage: misalignment can cause the belt to slip off its pulley, resulting in reduced power transfer and system inefficiency. Reduced system efficiency: it gradually reduces belt performance by increasing wear and fatigue, resulting in increased energy consumption.
Belts that are too tight put an excessive load on pulleys, shafts, and bearings. Excessive belt tension will also wear out a belt quickly. Proper belt tension is 1/2 inch of sideplay both ways. Press down on the belt midway between pulleys and observe the travel.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Read Full Q/A … : Sport & Outdoor – Others

Hi,
After a recent snowstorm, the auger stopped turning on my Troy Bilt Two-Stage Snow Thrower (Storm 1130). I inspected it and found that I broke two shear pins and the auger drive belt appeared to need replacement. So, I replaced the pins and then replaced the auger drive belt, following the instructions in my operator’s manual. Now, when I hold down the lever that should cause the auger to start spinning, I get white smoke coming from the machine and a smell of burning rubber. I’m assuming I installed the drive belt incorrectly, but for the life of me, can’t figure out what I’m doing wrong. More significant snow is on the way tomorrow, so any quick answers/suggestions would be MOST appreciated!!!
ANSWER : The shear pins shear because the auger is stuck or the shaft it is on has seized bearings
work in that area

Read Full Q/A … : Sport & Outdoor – Others

Not sure how to replace the belt in my MTD, Wards snowblower
ANSWER : Remove the housing with the machine offThe idler pulley is designed to push up against the outside of the belt between the drive and motor pulleys when disegaged the belt should look like a loop like a race trackengage the blade clutch and watch to see if it presses up against the drive pully and the motor pulley their should be a spring attached to the idler arm and i believe the new belt is dragging a littleyou should be able to move the belt with your hands ( it should slip freely) rod is engaged or it pulls the idler away Either a spring causes tension when the rod is engaged or it pulls the idler away Keep working with it until it is free you may have an adjustment on the spring tension or the linkage rod has an adjustment I am sure you can do this without an diagram good luck

Read Full Q/A … : Sport & Outdoor – Others

Have a john deere 318 riding lawn mower. it had been hard to start with it taking several turns of the key to do anything, then would not always engage. once engaged, would start with no problem. now when the key is turned, does nothing. checked 2 fuses near battery and tried jumping but no change. suspect starter and or solenoid. john deer shop claims starter price is $505 with almost 4 hrs labor too. is there good way to test to see if starter, solenoid, condenser, switch, etc is problem? what is the easiest way to access and remove the staqrter and solenoid? is there a relatively cheap equivalent to this starter and solenoid?
ANSWER : Usually the shop would make the fixing of an item to look so complicated this is usually to ensure that the customer comes back. To confirm if the starter is the cause of the machine not starting. tell the shop to check the machine if either of the 2 options are the cause of the problem as they will have setup procedures for doing this. Do not settle for cheaper equivalent as this will only cause further damage to the unit. It is rather concrete that starting problems are caused by the starter.Hope this has been helpful?

Read Full Q/A … : Sport & Outdoor – Others

Recently, I was using my Horizon CST 4.5 treadmill when the power on the treadmill and the room it was housed in went out. I reset the cicuit breaker and tried to get back on the treadmill. It turned back on, counted down from 3, and the time began however the running surface(track) would not move. I lifted the front end where the motor and belts are housed. I noticed that the belt was still intact. Unsure if motor is burnt out. Any help would be appreciated.
ANSWER : There is usually a small breaker on treadmills that pops out and you have to push it in to reset it. Take a look around the front of the treadmill and see if you can locate the breaker and reset it and the treadmill should work normally.

Read Full Q/A … : Sport & Outdoor – Others

Kawasaki bayou 1992, i changed the starter it turns but does not engage, the chain turns the gear moves but moter turns doesnt turn over.. what am i overlooking, ive tried what i know and nothing works..
ANSWER : Sheared pin on gears(if the gear turns but not the shaft)

Read Full Q/A … : Sport & Outdoor – Others

Unable to read camera on laptop to load pics
ANSWER : Consider NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won’t run down your camera’s batteries.Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system’s drag&drop facility to copy pictures from the card to the computer’s hard drive, the same way you copy any other files. Or you can use any photo cataloging program, such as Picasa ( http://picasa.google.com ).

Read Full Q/A … : Sport & Outdoor – Others