get it started. What position should it be in to start it.Then what rpm should it idle at.
Sport & Outdoor – Others
Experienced athletes share their insights in answering this question:
Hi there,Reset the screw to 2.5 out from bottomed then adjust as needed (do not increase much because it jurck arctic).post further comments for more information.Good Luck!!Thanks
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
Today, the bulk of our manufacturing happens at our facility in Thief River Falls, MN, with trails in our backyard and the mountains just a day`s drive away.
Set idle speed adjusting screw, clockwise to increase rpm, counter-clockwise to decrease rpm. Idle rpm range should be 950 to 1050 rpms. Adjust idle mixture by turning idle mixture screw slowly clockwise until the engine runs poorly.
Set idle speed adjusting screw, clockwise to increase rpm, counter-clockwise to decrease rpm. Idle rpm range should be 950 to 1050 rpms. Adjust idle mixture by turning idle mixture screw slowly clockwise until the engine runs poorly.
If the pilot jet is clogged, not enough fuel will be mixed with the air being sent through. Like a vacuum leak, this will result in a lean fuel mixture and a high idle. The simple solution to this problem is to clean the carburetor`s pilot jets.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
2006 Arctic Cat ATV dies after about 15 minutes of riding
ANSWER : It Sounds like your Stator is going bad.
I would have it checked/Diagnosed by a Local Shop.
I have a 2001 Yamaha XL700Z Waverunner. The compression on both cylinders is about 120, it starts and runs fine – dry. Won’t quite idle, but I can start it and rev it up fine (for a short period, of course). However, as soon as it gets in the water, it will barely run – it will start and sputter and you cannot get it to run more than a few seconds or rev up. Take it back out, let it dry, starts & revs fine. It is not getting any water in the casing that I can tell, its almost as if water is getting something wet through the cooling system that I cannot see?
ANSWER : Try cleaning the carbs and the fuel lines, filter
HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).
There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.
Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?
Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.
I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.
Thanks for listening!
ANSWER : Have you been able to find a solution to this problem. I am having the same issue.
My 50cc mini bike starts then dies 5 secs after starting. why?
ANSWER : It sounds like you may have 2 problems
Bad gas
dpossible loose spark plug( bad compression) Solutiondump out the gas put new inRemove the spar plug and examine the plug if it is wet and black it is fouledif it is white ad dry it is not getting gasIf you can replace the spark plug if not just clean it with a wire brush put back in and tighten Finally make sure the spark plug wire is not loseBest of luck to you
I have a problem with my machine, on occasion, not recognizing when I’m starting, and the display will not start. I have to remove one of the batteries or it will stay on forever. When it starts up, it works fine, no complaints whatsoever. But lately, I’ve not been able to use it due to the start-up problem. I put the batteries in, the display comes on, but it will not start up when I begin motion. The control buttons will not work, either. Please inform me what it is I can do to fix this problem. Thank You
ANSWER : Troubleshooting on this model is very limited to anyone but the vendor. I would recommend sharing the symptoms with a representative from fitnessquest here.
Good luck
I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.
Cannot turn engine over to start. Ariens 924 snow blower
ANSWER : Pull spark plugs and see if it will pull over if not fuel may have filled the crank case drain & refill to proper level (starter is stuck in lube shaft & movethe gear up & down by hand to free up)
