doesnt work. how do i unlock my safe?
Stack On 16 Gun Safe with Combination Lock

Experienced athletes share their insights in answering this question:
After 3 trys the keypad does go into lockout mode but it should only last for about 15 minutes and then let you retry 3 more codes to try and open. if you still do not know what the combo is you can usually call the maker of the safe and with the serial number you might be able to get the original combo that the safe was set to when it was purchased ( this is a factory set combo ) — now if that does not work, your next step will be to call a safe tech ( locksmith ) to set up a auto dialer,, this takes about a full 24 hours to get the combo right. the safe tech can also drill a small hole behind the dial and manually remove the locking bolt. after the safe is opened the locksmith will fill the hole and reset the combo for you ( also replace the battery at this time too ).

c…

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Battery failure is the most common reason the electronic lock on your gun safe isn`t working properly. Typically this is because the battery is dead. But, your electronic lock might also not be working properly if the battery doesn`t have enough amperage.
A: Unfortunately, you cannot reset this lock without knowing the current combination. You`ll likely need to purchase a new lock.
You can visit a Master Lock Distributor / Retailer or submit a Lost Combination form. Bring your lock to the retailer. Be sure that it is not attached to anything. If you do not bring the lock, or it is attached to something, we will not release the combination.
A three digit lock can have its key value between range “000” – “999”. So basically 1000 combinations have to be tried to open the lock.
There are 504 different 3-digit numbers which can be formed from numbers 1, 2, 3, 4, 5, 6, 7, 8, and 9 if no repetition is allowed.
Three digits numbers start from 100 and end at 999. So, the smallest three-digit number is 100 and the largest 3-digit number is 999.
If you enter your code into the electronic safe lock incorrectly several times in a row, you will be locked out.
If you have a keyed safe, the first thing to do is to check if the key is bent or damaged. If so, it is recommended that you contact a professional locksmith to repair or replace the key. If the key is not the problem, it is possible that the lock is jammed or defective.
If you forget the combination to your Master Lock, you can cut it off quickly. Master combination locks have a hardened steel shackle that cannot be cut with a standard hacksaw blade. The shackle is hardened steel to deter thieves from breaking it.
examples. A 4 digit PIN number is selected. What is the probability that there are no repeated digits? There are 10 possible values for each digit of the PIN (namely: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9), so there are 10 · 10 · 10 · 10 = 104 = 10000 total possible PIN numbers.
Answer: The highest three-digit number in the decimal is 999. Explanation: If you add 1 to this number it becomes 1000 which is a four digit number. So 999 is the highest three digit number in the number system.
It can take anywhere from 7 seconds to 45 minutes for a locksmith to pick open a lock. Generally a locksmith should be able to unlock most doors in about 10 minutes. Of course this is effected by the type of lock.
By that I mean I will write five as 005 and twenty-three as 023 etc. The smallest 3 digit number I have is zero, written 000 and the largest is 999 and I have ever integer between 000 and 999. Thus I have 1,000 numbers or 1,000 possible combinations.
Given 3 digit numbers that can be formed using the digits from 1 to 9. Required number of 3-digit numbers= arranging 3 digits with the total number of 9 digits.. Hence, the required number of numbers =504.
Which Is the Largest 3 Digit Number? The largest 3 digit number is 999. The smallest 3 digit number is 100.
Original question

You can choose any of the 5 numbers as your first digit (5 options). For your second digit, you can also choose any of the 5 because repetitions are allowed. This gives 5⋅5 possibilities. Add in a third digit, once again choosing from the 5 numbers, and you have 5⋅5⋅5, or 125, possibilities.

One safe may go into lockout mode after one failed attempt where other safes may give you up to 5 attempts before it locks you out completely. There is no universal setting for when a safe will go into lockout mode.
Many safes go into penalty lockout mode if too many wrong codes are entered. Depending on the type of keypad, it typically emits a rapid series of beeps. If this happens, wait 10 to 20 minutes, and try again. Your safe also may have a time delay.
Your safe`s owners manual should provide instructions on how to change your dial lock`s combination. While you can change the combo on a mechanical lock, it can be tricky if you haven`t done it before and know what you`re doing.
The factory preset code is 1 – 5 – 9 – # and should be changed before using the safe.
Best Way to Break Into a Safe: Call a Locksmith

But they are highly experienced and have all the proper tools for the job. Depending on the safe, they may be able to break into the safe without damaging it and do so in a reasonable amount of time. At the very least, give a local locksmith a call and ask questions.

A store associate at the customer service desk will be able to call the Master Lock Customer Service line at 1(800)308-9244 to retrieve your combination for you.
The combination is made up of three numbers – When entering your combination, you must enter the numbers in the order shown on the combination tag. stop when the first number lines up with the indicator. the first number, and stop when the second number lines up with the indicator.
Bolt cutters are the common tool of choice for to cut padlocks during forcible-entry.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have The Protector model #6742Df electronic combination. It came with a key, I’m guessing will open it if the electronic key pad runs out of power. The key pad is not lit and my wife lock her key in the safe. Can I order another key?
ANSWER : Yes you can order a new key from the manufacture or if you see numbers and letters ( key code ) on the face of the lock cylinder you can call a locksmith and they should be able to cut you the key by that code as well. if there is no code on the lock then you can have a locksmith pick it open and also make a key. either way — a locksmith will be your fastest way to get the key.

c…

Pro-form 930i, 2003 model, after not used for 30 days, left plugged-in, will not work. Recalibration efforts with Pro-form didnot work. When unplugged/replugged console shows all 888s for a second, otherwise shows 2 different sets of numbers, 1 all zeros except incline which is 0.5 and the fan works with this, 2 a set of different numbers like 10 and 100, etc. and the fan does not work with these numbers. Thanks for any help you can be.
ANSWER : There is a main processor thst controls all the fuctions, and if you unplug it from the wall for 40Min., it should reset back to normal.

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
ANSWER : I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.

Gun safe key lost – Stack-On Stack On 16 Gun Safe with Combination Lock
ANSWER : You csn get nfor from safe company that made it.. or just spend money on a lock smith….

I have a treadmill Nautilus 516, I mark an error e7 flashing. I already unplugged, lubricated, and clean the speed sensor with alcohol and a clean head cotton. When I jump in at the front it locked out like when you put it in position for move it. When I put start in 4 seconds get the error e7; and when the error still the jump in the front and locked if I put in the back of the walking part do not locked out but still get the e7.
ANSWER : Hi,It stands for a lost signal in the console wire harness. It could be one of the wires has been broken or there is a connection loose. unplug and replug all connections. Then check for continuity in all the wires in the harness. Try to enter the service mode, press Stop Belt, Faster, and Slower
simultaneously. P000 appears in the Select display, indicating that no
key is pressed. To exit the service mode, press and release the same three keys simultaneously or press Power twice to power up into normal mode. Check
the speed sensor to make sure it is within 3-4 inch from the front
roller (magnet). Then check the sensor wire harness to make sure it is
fully seated on the lower control board. If the problem persists, then you need to inspect the machine properly as it could be a faulty console/control board /speed sensor.Let me know,if needed further assistance.Hope i helped you.Thanks for using ‘ Fixya ‘ and have a nice day!!

My reebok i run treadmill was working fine,till my son pulled out the safty key.Now it won”t work at all ! The light is working on the on off switch,but the display is not on nor the belt moving.I have put the key back in,and tryed turning it off for a few minutes.But nothing is happening,there is a small button by the on off switch,not sure if its a reset button, but it is doing nothing, please help. 🙁 x
ANSWER : Welcome to FixYa.

Please provide me with the complete model number of your treadmill so that I can assist you further.

I’ll be waiting.

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.
ANSWER : You can contact the Remington directly who will ship you a free users manual. Here is the company’s Contact Us details:

http://www.remington.com/pages/our-company/our-company/company-info.aspx

You may also find the required answer in the official help center. It covers almost every fields. Here is the link:

http://remington.custhelp.com/