I am looking for a user manuel for the Pro Form 480 LE elliptical space saver. Where can I get one?

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

I have a TX500, never been used (just out of the box) and had to get an electrician to my home for this problem. It will start rolling but quits in a few seconds. The electrician believes that it is a problem in the sensor that rides at the belt. There is only one sensor in the pulley; he thinks that perhaps there should be two as there is a hole placement opposite the one that is in there. When the belt quits, it goes to a number 3 on the board which he thinks is the sensor as well. If he is correct, where do we get another magnet to place there? If he is not correct, please offer help. We did not get a owners manual in the box and surely could use one; where can we get one? Please help…thankyou

I own an 1992 Yamaha Phazer II PZ 480. I have done a bunch of work trying to get this hunk o stuff going. I have good spark and compression from the motor. I rebuilt both carbs and both clutches it starts and runs fine but when I try to move it just boggs down- no power? Where should l look next to get this thing moving again? I work at a Marina that used to service sno-mobiles so I have the tools to get it done. Could you maybe send me an assembly diagram of where to look and what to do next? Thanks

Bike pedal is striped , get a new one or buy new bike?

Help! Just bought a Remington 30 06 for my grandson that has a Bushnell Sportview U4124 4-12power scope mounted on it. I would like to sight it in at 100 yards using a 180 grain shell but I don’t have the owners manual and I don’t understand an on line explanation that I found. This is the on line message: “You’ll see two horizontal crosshairs, put the top one on the animals back then zoom in until the bottom one is on his stomach. Look at the numbers on the zoom dial there should be three lines they are D – deer, E – elk and A – antelope. The numbers are the distance to the game, you then turn the external elevation knob or turret to the matching distance and shoot dead on. No need to hold over for bullet drop. The sad part will be if you didn’t get the other turrets that would have come with it as they are calibrated to different calibers and bullet weights”
I don’t understand how to set the elevation knob to 100yards when its lowest shown number is 150. If I need other turrets how or where can I get them? Thanks, a frustrated grandfather.

I am trying to get the pictures from my camera finepix j210

I have a Scuba Pro X650a regulator. After having the unit serviced this winter I used it last month for the first time in St. Croix.

The first day of diving went fine. However, as the week progressed I noticed that when taking in a breath the regulator continued to trickle air at a very small rate. While not enough to be concerned about safety at this point it has become an annoyance both from the fact that bubbles continue to trickle past my ears and air usage has increased. This is an intermittent problem.

I had it looked at by 2 certified Scuba Pro Dive shops and they could not find anything wrong with it though one did lower the first stage pressure just to a bit to see if that would work. I also cycled the control lever position for “dive” and “surface” intervals to ensure that there were no sticking problems.

It does appear that the problem is intermittent and that it only occurs when the regulator is under water.

In addition is there a diagram in which I can use to troubleshoot this problem?

NOTE: this version of the X650 was not on the recall list of Scuba Pro.

Any help would be appreciated.

Stephen