Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Hello,

You have to fain access to the impeller, inside the pump. Remove the impeller nut, and the shaft will come out with the motor.

–W/D–

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

How do you fix a clogged pump impeller?
  1. Turn off the electricity running to the pump motor at your circuit breaker. …
  2. Remove the pump basket lid and the pump basket.
  3. You can use a bent coat hanger or just your fingers to reach into the impeller. …
  4. Pull out anything you find and clean your hook now and again.
21 déc. 2021
How to remove a stuck Hot Tub Filter?
  1. Turn the power to the hot tub off.
  2. Use a strap wrench to create a lever that will help remove the filter.
  3. Drain the water from your hot tub (if necessary)
13 août 2021

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.

See less

ANSWER : Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up

Read Full Q/A … : Sport & Outdoor – Others

My daughter has a sweet pea scooter that had been blowing fuses and the motor got hot. Im sure the motor is shot. but my question is can anyone tell me if the motor would be the only thing I need to c
ANSWER : Find out whether it is 6 volts or 12 volts and there should be two wires that feed the motor either cut or splice and attach another set of wires with fuse in the line (simular to jumper cables) raise the back tire so it does not touch the ground and place jump wires to the negative and positive of the battery.If the motor moves in either direction without blowing the fuse the motor is good if not then its bad. Uses the same amperage fuse

Read Full Q/A … : Sport & Outdoor – Others

Motor was running great, but it died slowly and never start again
ANSWER : Check to see if you have a spark -then check if you are still getting fuel-and how old is the fuel-because it is recommended ,an im assuming its a 2 stroke motor,that the fuel should be replace with a fresh 2 stroke mixture every couple of months as the mixture jellyfies and sludges up the carb etc-try those first

Read Full Q/A … : Sport & Outdoor – Others

TC5000 and after extended use I smell burning and upon removing the belt cover and drive belt I felt of the motor on the motor side of the drive pulley and it was ”red-hot”, obviously the source of the smell of the burning. The motor spins freely without any rubbing noise. The drive pulley (motor side) and the tread pulley appear to be alligned. One curious thing is that the threaded motor output shaft is recessed about 3/8” from the outside edge of the pulley. Could it be the bearing on the pulley side of the motor? I am dumbfounded as to what the solution might be. Note that I could not enter the exact product as my model seemed to be invalid. My model is the TC5000. Thanks [email protected]
ANSWER : Just because it spins freely doesnt mean it cant have a shorted winding. Id send it back where it came from or at least replace the motor.

Read Full Q/A … : Sport & Outdoor – Others

2005 4 stroke yamaha 150 550hrs. normally use every week but due to surgery not used for 10weeks. Just before I went down I changed internal fuel filter, and zincs in motor. finally put in sunday. motor started fine left dock hit the power and started to come up on plane then stuttered and died. changed the external fuel/water seperator pump up the primer and started up again. with in a minute died down again. limped back to dock checked fuel filter and plug wire connections. pumped up primer and left dock went right onto plane for maybe 150yds then coughed and died. I could pump up primer and it would run but then die out. the fuel filter at the front of the engine would run dry until I pumped it up again. If it were a car I would suspect a leak in a fuel line but I can’t find any sign of one.
before we launched I put 10 gallons of fresh fuel in and added another bottle of ethanol stabilizer (CRC brand)
what proceedure should I follow to isolate the problem? I am a fairly competent mechanic as far as cars and trucks go. I don’t really want to have to take it to a marine mechanic.
ANSWER : This is going to be the fuel pump is not pumping any fuel. The primer is acting as a fuel pump. When you prime it, it gives the engine enough fuel to run for a little bit. But as soon as the fuel runs out, the engine is dying. So this is going to be a bad fuel pump.

Read Full Q/A … : Sport & Outdoor – Others

I own a 1998, 25hp Mercury short shaft tiller outboard engine. It is on a 15′-10″ Mirrow Craft semi V aluminum flat bottom boat. When I am running it, the steering handle pulls to the left making the boat turn right. I have to concentrate on keeping the handle steady when the motor is at full throttle. If I would let up the tension with my arm the motor pulls the boat to the right. I need to balance the motor so it runs without steering tension. How do I adjust it?
ANSWER : You have a tiller tab on the foot of your outboard, It has a mark on it, and should be cocked to one side, take note of the mark, and turn it one way or another, just keep notes on what you do, then try it. See what happens, you should be able to compensate for the over steer by moving this tab. Hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

How do you pull the pump free from the motor, flo master
ANSWER : Hello,

You have to fain access to the impeller, inside the pump. Remove the impeller nut, and the shaft will come out with the motor.

–W/D–

Read Full Q/A … : Sport & Outdoor – Others