How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
You can read fault codes on a WaveRunner with special diagnostic software. The two most commonly used softwares are the MEDS (Marine Engine Diagnostic Software) and the CandooPro. You have to install them on your computer and connect it to the WaveRunner with a diagnostic cable, which is included in the package.
Fault Code 163: Demanded Brake Application Pressure.
Find it in the lower corner of your windshield on the driver`s side. Your VIN number is your vehicle identification number and you can find your engine size by VIN number. In the series of numbers and letters, the tenth from the left denotes the model year and the eighth is the engine codes.
Press the odometer`s Trip and Reset buttons while turning the ignition key ON. After turning the key ON, release the odometer Reset and Trip buttons to check if the Diagnostic Trouble Code or DTC appears on the odometer display.
Locate the 3-pin cluster/diagnostic connector in the front storage compartment of the ski. You may need to open an access panel on some models to get to the connector. The connector is a three pin dark gray connector.
There could be several reasons why a WaveRunner is not starting. The simplest and most common fault is when the shut-off clip is not properly attached or the tank is empty. Other common reasons could be electrical issues like malfunctions with the battery, spark plugs, fuses, or wires.
Error 39 indicates a miss-communication with the injectors has occured, after 5 attempts the ECU will go into a lock down mode which requires the ECU to be reset, this is not something you can do through the Diag on the dash.
P0124 is a diagnostic trouble code (DTC) for “Throttle Pedal Position Sensor/Switch (TPS) A Circuit Intermittent“.
A low-hour ski is a machine that has been used for less than 50 hours, while 150 hours or more of use is considered high. If a PWC is 5 years old, you should expect it to have roughly 150 hours logged.
However, failing to clear a code after a repair could leave you second-guessing the issue or doubling your work to recheck the codes. That`s why you should always make clearing codes an essential part of your repair process.
To reset a check engine light without a scanner, disconnect the negative battery cable and wait a few moments. This will reset the diagnostic system in your vehicle, and if the underlying issue has indeed been resolved, the light should go off immediately.
Diagnostic Trouble Code (DTCs) — Trouble codes are how OBDII identifies and communicates to technicians where and what on-board problems exist. The first number in the DTC indicates whether the code is an SAE generic code (applies to all OBDII systems) or is specific to the vehicle manufacturer.
Diagnostic trouble codes (DTC) are automotive computer codes stored by the on-board computer diagnostic system (OBD) in your vehicle.
There are thousands of possible diagnostic codes possible, some that are specific to a manufacturer or particular vehicle, and many that are generic across all vehicles.
The Engine Control Unit (ECU) is essentially your jetski`s `brain` and controls various engine functions, including RPM Limits, Timing, fuel and throttle position.
If you do run your WaveRunner out of the water without proper water supply, it should be for only fifteen seconds maximum. If the jet ski is not in the water or getting a proper supply of water, the engine and exhaust are at high risk of overheating.
What`s Considered a Lot of Hours on a Jet Ski? When it comes to engine hours, first and foremost, you want to ask the question: How many hours does a jet ski engine last? As a rule of thumb, the 2-stroke jet ski engines last around 200-300 hours, while the 4-stroke jet ski engines last around 300-500 hours.
You can start a WaveRunner out of the water without any damage, but the manufacturer recommends that you don`t run the engine over 4,000 rpm! If you can`t attach a hose to the flushing port, you can run a WaveRunner for only 15 seconds, but by supplying water, it can be run much longer.
The external temperature makes a difference
If you are charging your battery at room temperature, it will take around 4-6 hours with a standard size charger. However, if you are charging your battery in cold temperatures, you may need to reduce the amount of current that you`re using.
Reboot your PC. Giving your computer a chance to reset can fix any number of issues that might impact your connectivity to the game. Reset your router and modem. Rebooting your modem can fix connection problems, improve slow connections, and clear out any issues stored in the memory of your router.
Check for Tight Connections: There are 4 wires from the motor to the controller. Make sure you do not have any loose connections on the motor or controller. If these are loose, it can trigger Code 31 to appear.
Error code 71 was an easy fix on my bike, battery rattled over bumps, got error code 71, fix = Lock battery in position, take out key, slacken two bolts holding lock, adjust lock so no battery movement, tighten bolts, caution bolts go into brass nuts s…
70 – Error organizations idling (as a symptom: the engine begins to stall at idle after 20 minutes of work);
Behavior – The inverter disconnects from the grid. Troubleshooting – Carry out AC reset; The test is repeated.