Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
This error code can mean a few things. Here is a troubleshooting pdf

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Error Code: E1

An E1 code just means that the console is not getting a reading from the reed switch (Speed Sensor). If the running belt moves for several minutes and then produces the E1 error, this is most commonly a result of the running belt needing lubrication.

When the E1 error occurs, check that the speed sensor of the treadmill is not too far from the magnet (2-3 mm max). Then verify that the sensor is working.
The E1 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor. Try unplugging the unit and waiting 2 minutes for the power to discharge. Then plug the unit back in.
If the E1 error occurs after the belt starts to move for several seconds, the error code means that the system is not picking up the speed of the motor. This pickup comes from a magnet mounted on the front roller pulley and a speed sensor, or a problem with the magnet.
E11 Error: Over-current deceleration detected. Resolution: Ensure that the treadmill is connected to the external power source and that the proper voltage necessary to power the treadmill is available.
E1 Error code means the correct water level has not been reached within 20 minutes of the washer starts. Check the following: Check that the water faucets are not closed. Check that the water pressure in the house is over 20 kPa.
E1- Electrical components

Try to pull the rubber handle on the handlebar slightly out from the throttle lever, often this error code is due to the rubber grip and the throttle lever being too close. After this you can check that the on and off button in the display works properly.

E1 on a tyre pressure machine is an error code. It can mean several things including that the air plug is disconnected, the pump is applied too loosely to the valve or there is air leaking from the valve.
The EL01 code typically is associated with loss of communication, with the video explaining common causes and what actions you can take.
An E1 error code is associated with a draining problem. Either it is not draining or not draining in the time specified. Check that the drain hose is not blocked or kinked, thereby stopping or slowing the flow of the water when the machine is draining. If the hose seems to be OK check that the drain pump is working OK.
What does E02 error mean? Reason 1: Communication cable fault. The communication cable is how data is sent from the motor to the treadmill screen. The cable is located inside the right upright post of the treadmill base. It can sometimes become trapped or twisted causing the error to show up.
E4 Error: The motor drive has detected excessive drive output current. Resolution: Ensure that the treadmill is connected to the external power source and that the proper voltage necessary to power the treadmill is available.
E2 Error(s): Treadmill is overloaded. Resolution: Check the treadmill motor for signs of overheating (strong smell, grinding noises, inconsistent operation speeds). If the motor appears overheated, ensure that the treadmill is properly lubricated.
If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It`s possible the drain hose extends more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.
E1 – Indoor / Outdoor Unit Communication

In general, an E1 error code indicates that communication between the mini split system`s indoor and outdoor units has been impeded. It could be struggling with intermittent connection issues or have failed entirely.

An E1 error code indicates there is a potential problem with the high level alarm cable. The most common cause of an E1 is the float cable being extended to over 20m (overall length).
The F9E1 Error Code indicates that the washer/dryer is not draining in a timely manner, or at all. This could be due to the following: Drain Pump on the Washer/dryer may need to be cleaned. See Cleaning and Maintenance symptom above.
This can happen for one of two reasons. The first is very straightforward. The battery bank is actually over-discharged. If the battery voltage (12V system) is below 11.1V it will trigger the E01 code.
“E1” – High Pressure: The pressure of the compressor is too high and the high pressure switch is open. The `Error` LED will be on. Solution: Ensure exhaust duct is not blocked/kinked.
E130. Flue Gas Temperature. Sensor/ Air Pressure Switch. If unit can be reset (Pressure Switch Activated)
E1:This error code indicates the unit is experiencing high pressure. The most common causes of increased pressure in your Gree mini split air conditioner are dirty coils, failed fans, overcharging, or a faulty high-pressure switch.
If your air conditioner displays E1 in the display panel and won`t turn on, it means that the Room Thermistor (a device connected to the thermostat that detects room temperature) is shorted or defective, and you need to have your air conditioner serviced.
The F5E1 Error Code indicates that there may be an issue with the door switch/door lock. The door is unlocked during a cycle when it should be locked. Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
System error codes are provided to software programmers as part of the programming interface with the Windows operating system. In other words, they are predefined error codes and messages that programmers can use with their software to tell you (the user) that the program is experiencing a particular problem.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a Kohler Condidant 5 Generator that will run as long as you hold the start button in. It dies when you let off. I have a harness for the remote switch but no switch – It also will start the generator when you cross the red and black wire and run as long as you hold them together. There are 3 wires to the main switch and 5 to the remote switch. Does the starter stay engaged the whole time you hold the start switch or does the computer release the starter once it is running? The Generator is producing electricity because I tested it while holding the start button. Some where is a wire that shold tell it to keep running. I have read online many descriptions of the same problem, most are told the board is bad so they replace it and still have the problem. Have not found a solution. Talked to a marine machanic today and he said he fixed his friends generator doing the same thing by running a bypass wire but he couldnt remember exactly what he did it was a long time ago. Can anyone help me. Thank you
ANSWER : The problem is either the ballast resistor or the starter bypass relay. The bypass relay should be part of the starter solenoid. I’m afraid I can’t tell you exactly where the ballast resistor is located. It should be a physically fairly large resistor made of ceramic. It should be retangular roughly 1.5″-3″ long and 3/8″-1/2″ accross with a wire on each end. It could also be a coil of wire mounted on a phenolic board.
If you need more help just add a comment and I’ll respond as soon as I get the message.

Read Full Q/A … : Sport & Outdoor – Others

Motor was running great, but it died slowly and never start again
ANSWER : Check to see if you have a spark -then check if you are still getting fuel-and how old is the fuel-because it is recommended ,an im assuming its a 2 stroke motor,that the fuel should be replace with a fresh 2 stroke mixture every couple of months as the mixture jellyfies and sludges up the carb etc-try those first

Read Full Q/A … : Sport & Outdoor – Others

My 50cc mini bike starts then dies 5 secs after starting. why?
ANSWER : It sounds like you may have 2 problems

Bad gas
dpossible loose spark plug( bad compression) Solutiondump out the gas put new inRemove the spar plug and examine the plug if it is wet and black it is fouledif it is white ad dry it is not getting gasIf you can replace the spark plug if not just clean it with a wire brush put back in and tighten Finally make sure the spark plug wire is not loseBest of luck to you

Read Full Q/A … : Sport & Outdoor – Others

Hi, I have a commercial grade treadmill, the Technogym Run 600XT Pro that gives the error code E5 (incline fault) that I can’t get rid of. What happened was that after cleaning under the motor cover and turning the treadmill on again this code appeared. What had happened was a wire had come off what looks like a safety switch on the side which I assume trips if the treadmill goes too high. Put the wire back on now I can’t get rid of this error code. Is there a way to reset it from the console please as there isn’t a fault and it was working fine before the wire came off (it didn’t touch anything). Thanks a lot.
ANSWER : Hi.If there is incline fault, then the sensor must be calibrated. The error may happen even if you do not do anything. sensor goes out of calibration and you get e5. The only reset you can do is by disconnecting power and removing console batteries if installed (that depends on the treadmill model).I suggest contacting Techogim and following the procedure to calibrate the sensor. Contacts are listed at the right hand side of this page, click: Contact Us.

Read Full Q/A … : Sport & Outdoor – Others

I have a 99 yamaha f100 four stroke outboard. Problem I have is boat will acclereate fine get up on plane and after running for about a mob at wot will decell and only run around 4500 rpm. Then after coming back to idle will have a slight miss then run smooth and repeat every run. Changed the plugs and fuel filters alll oe yamaha has fresh oil timing belt is good any ideas will help or fuel psi spec. I am an ase master automotive tech so I know alot about engs. To me it feels like it’s running out of gas. Like the carb bows are full when I take off but then runs out after running wot. Any info will help
ANSWER : I have exactly the same problem with my Yamaha F100, have you got any solutions yet?

Read Full Q/A … : Sport & Outdoor – Others

I have a problem with my machine, on occasion, not recognizing when I’m starting, and the display will not start. I have to remove one of the batteries or it will stay on forever. When it starts up, it works fine, no complaints whatsoever. But lately, I’ve not been able to use it due to the start-up problem. I put the batteries in, the display comes on, but it will not start up when I begin motion. The control buttons will not work, either. Please inform me what it is I can do to fix this problem. Thank You
ANSWER : Troubleshooting on this model is very limited to anyone but the vendor. I would recommend sharing the symptoms with a representative from fitnessquest here.
Good luck

Read Full Q/A … : Sport & Outdoor – Others

2008 Yamaha vx deluxe will only run about 30 mph
ANSWER : If the motor is reaching full revs look at the jet assemby for fouling or prop damage. If it is not reaching full revs get authorised mechanic to fix it, it will be cheaper in the long run.

Read Full Q/A … : Sport & Outdoor – Others