tried searching on the internet but have not been able to find it – could you please help me locate a copy as soon as possible Thanks
Sport & Outdoor – Others
Experienced athletes share their insights in answering this question:
You can get a user/instruction manual for Jazfit S1 treadmill, but it’s not freely available anywhere. You need to buy it.
If you agree to pay, you can get all kind of Jazfit manualshere: http://manuals-market.com/search.php?cmarque=PERFORMANCE%20TEKNIQUE&modele=ICBM%20779.
Afterclicking this link you will be forwarded to a page contains a form. You need tofill up that form. Most of them are pre-filled. You need to write “Jazfit” inBrand box and model number in “model number” box. Please don’t forgetto mention “treadmill” in the “description box”. Finally accepttheir “terms and condition” and click on “search” tab.
Downloaddocuments as per your requirement.
Hope this will help you. Good Luck.
If you agree to pay, you can get all kind of Jazfit manualshere: http://manuals-market.com/search.php?cmarque=PERFORMANCE%20TEKNIQUE&modele=ICBM%20779.
Afterclicking this link you will be forwarded to a page contains a form. You need tofill up that form. Most of them are pre-filled. You need to write “Jazfit” inBrand box and model number in “model number” box. Please don’t forgetto mention “treadmill” in the “description box”. Finally accepttheir “terms and condition” and click on “search” tab.
Downloaddocuments as per your requirement.
Hope this will help you. Good Luck.
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
Most iFIT-enabled treadmills have a pinhole reset button located somewhere on the console. To reset, turn the machine off, press the reset button with a paperclip or equally narrow tool, and hold it down while turning the machine back on.
Check your outlet first, ensure the power cord is connected securely, that the cord and plug are free of damage. Now power cycle the machine by flipping the reset switch to off, then back to reset. Insert your key into the machine. If the power doesn`t come on test the outlet by plugging in another appliance.
Treadmills require lubrication to limit the amount of friction between the platform and belt. When the friction increases to a certain point, the machine is automatically set to power off. This may be the cause for the machine to stop working suddenly. Try lubricating the belt.
Simply push the “Start” button on your machine to begin a workout in manual mode. You`ll be able to manually adjust your settings, and your screen will display an oval racetrack or similar graphic as you work out.
Insert the paper clip into the pinhole. As you insert the paper clip, press, and hold it down. As you hold the paper clip, have the second person flip the power switch back on. Once your machine`s screen lights up, you may remove the paper clip.
Double-check that all connections are secure, especially the console cable. Unplug and reconnect the console cable to verify. Make sure the console cable is not pinched or damaged in any way. Plug the treadmill in, turn the power switch on and look for any lit LEDs on the motor control board.
This is likely to be a problem with the wire connection. We would suggest you check all the wire connections on the treadmill starting at the base of the machine and working your way up to the right hand handrail connection.
According to what the manufacturers say, the average life of a treadmill is about 10 years. However, if you take care of your treadmill properly and lubricate the belt regularly, you can make it last longer.
If you don`t want to use iFIT, identify the gray button on the back of your treadmill to reset it. Then, head to the front of your treadmill, wait for it to flash hello, and press the iFIT button for several seconds. Once you see several zeros on the screen, you can start using your treadmill without iFIT.
Check the drive belt for proper alignment. With the cover still off, check over the wire and cable connections, as they may have become loose or disconnected during shipping or assembly. Make sure connections are secure and no wires are crimped, damaged, disconnected or burnt.
Generally speaking, yes. Manual curved treadmills are better than electric treadmills for most people, especially if they want to get a more intense workout in the same amount of time. Manual flat treadmills have a time and a place, and they may be the best option for some people.
A manual treadmill operates under your own power rather than needing to be plugged in. Basically, you are the engine or motor. An electric treadmill has to be plugged into a power outlet because the motor runs on electrical power.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
See less
ANSWER : Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up
Read Full Q/A … : Sport & Outdoor – Others
I have a TX500, never been used (just out of the box) and had to get an electrician to my home for this problem. It will start rolling but quits in a few seconds. The electrician believes that it is a problem in the sensor that rides at the belt. There is only one sensor in the pulley; he thinks that perhaps there should be two as there is a hole placement opposite the one that is in there. When the belt quits, it goes to a number 3 on the board which he thinks is the sensor as well. If he is correct, where do we get another magnet to place there? If he is not correct, please offer help. We did not get a owners manual in the box and surely could use one; where can we get one? Please help…thankyou
ANSWER : Hello,I believe the best thing to do at this point is to look for a way to get the manual of the device, this will give a full guide and better understanding on how to fix this problem.Check maualnguide.com to search for the manual of the device, the link provides almost all manuals to all device.Take care.
Read Full Q/A … : Sport & Outdoor – Others
We have model#38025 Toro 1800 snow blower that I am trying to fix. My husband accidentally got an electrical extension cord wrapped around the cylindrical curved inside and it’s jammed in pretty good. I have tried getting a manual online with no luck and we do not have a manual because the people who gave it to us forgot to give us the manual. I need to know how to get inside so that I can free the cord. Help please!
ANSWER : Here is the owner manual and the parts catalogue for your guide. You must have an Adobe Acrobat Reader installed in your pc to view thi file cause its pdf format.1. manuals/38025_operator_3327-516.pdf 2. manuals/38025_parts_3319-653.pdf
Read Full Q/A … : Sport & Outdoor – Others
Hello,
I am renting a home in NJ, and would like to open our pool. I am not very savvy when it comes to inground pools… i tried to figure out how to turn my Hayward S244T Hi Rate Sand Filter on, and get it going. While i did manage to get water pumping into the pool, it was not filtering out.
I am renting a home in NJ, and would like to open our pool. I am not very savvy when it comes to inground pools… i tried to figure out how to turn my Hayward S244T Hi Rate Sand Filter on, and get it going. While i did manage to get water pumping into the pool, it was not filtering out.
Can you please explain to me what i am suppose to do, and how to do it. I have an owners manual, but i find it very hard to follow, and everything is already installed, i am just having problems filtering it out.
Thanks!
Christine Mincer
ANSWER : Hello c anna…. Opening up the pool is a pretty big job with lots of steps. That said, here is an excellent link which has all of the steps broken down
http://www.poolcenter.com/spring.htm
Joe
Thanks for choosing Fixya!
Read Full Q/A … : Sport & Outdoor – Others
How do i lubricant my treadmill
ANSWER : It is an indicator that the belt needs lubricating. turn the power off, and lift up one side of the belt and spray a small amount of lubricant underneath the belt, onto the running board. repeat this step on the other side. turn the treadmill on and run it for a few minutes to spread the lubricant. the oil light should now go off.
this should be repeated every 5-6 months to keep the board lubricated and to reduce friction between the belt and board and will lengthen the life of your treadmill.
this should be repeated every 5-6 months to keep the board lubricated and to reduce friction between the belt and board and will lengthen the life of your treadmill.
Read Full Q/A … : Sport & Outdoor – Others
I have an 8100 ES Reebok treadmill. There is a squeaking noise coming from the drive motor. It is coming from the non-belt side (if facing the front of the treadmill, the left of the drive motor. When the treadmill is turned off, I can manually move the walking belt in the walking / running direction and it will squeak. If I move it in the opposite direction, manually it does not squeak. Also, if I need to lubricate the bearings can you tell me how to get to them to do this. The motor has plenty of power and no other problems, only squeaking. I have sprayed a belt lubricant on the belt and also blown it all out with a can of compressed air (used for computer key boards).
ANSWER : Hi.the bearings in these machines should be lubricated and sealed for life. they are not designed to be touched. it sounds like you have done the important bits. belt lubrication and blowing out any debris that may be there. squeaks like this can be incredibly difficult to find, but can also be incredibly annoying.the main things that you can do is keep watching to try and find exactly where the squeak is coming from and check for anything wrapped around the edge of the roller.keep using the belt spray, and the compessed air.a good grade silicone lubricating spray used at the edges of the rollers, by the bearings and around the motor and gearbox unit may also help but do not get this spray on the belt as it can be very slippery.squeaks like this can start and stop on their own or develop slowly and go just as slowly.keep doing the maintenance you are doing, and use the silicone spray as described above.it may take a little while for the spray to work its way into the bearings as they are fairly well sealed but you should notice an improvement after a few days.please feel free to ask for further advice if you need
Read Full Q/A … : Sport & Outdoor – Others
Recently, I was using my Horizon CST 4.5 treadmill when the power on the treadmill and the room it was housed in went out. I reset the cicuit breaker and tried to get back on the treadmill. It turned back on, counted down from 3, and the time began however the running surface(track) would not move. I lifted the front end where the motor and belts are housed. I noticed that the belt was still intact. Unsure if motor is burnt out. Any help would be appreciated.
ANSWER : There is usually a small breaker on treadmills that pops out and you have to push it in to reset it. Take a look around the front of the treadmill and see if you can locate the breaker and reset it and the treadmill should work normally.
Read Full Q/A … : Sport & Outdoor – Others
