YLINDERS, DOES THIS CONFIRM A BAD CD2 PROVIDED IT ISN'T THE WIRE IN BETWEEN
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
Hello.

You have done well to diagnose the problem, and you are correct. It is a bad CD2.
The CD2 interprets a signal from a magnetic pickup, and sends the spark accordingly to each cylinder. The unit is getting a input, or you would have no spark in either. that leaves only one possibility!
If you have a meter it would be worth while checking the wire also as these are subjected to vibration and heat, but it is rare.

I hope this points you in the right direction.
Regards
GM

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Loss of spark is caused by anything that prevents coil voltage from jumping the electrode gap at the end of the spark plug. This includes worn, fouled or damaged spark plugs, bad plug wires or a cracked distributor cap.
If there isn`t any spark visible when kicking the engine over, follow these steps: (1) Check the metal cap on top of the spark plug and make sure it is tight. Give it a gentle twist with a pair of pliers if it isn`t. (2) Make sure that the spark plug lead wire is solidly connected to the spark plug cap.
Engines with no spark or intermittent spark on one bank can be caused by a faulty stator. Nestled in with the stator under the flywheel is the trigger (or timer base).
If left untreated, a cylinder misfire can lead to significant engine damage. Worse, if you experience a bad misfire while driving, it could result in an accident. This is why it`s important to treat engine misfires as soon as you detect them.
A single spark plug that fails to ignite the fuel-air mixture can cause a halt in the running of the engine. It can result in incomplete combustion and damage to the catalytic converter of the car. Faulty spark plugs can cause the car to exhibit starting troubles.
Second stroke: combustion (or explosion) – exhaust

The compression causes a spark in the spark plug, which ignites the compressed mixture and creates combustion, which then pushes the piston downwards with great force.

Spark issues are the most common symptoms of failing stators, known as “Misfiring.” If you haven`t already known, stators are directly responsible for producing the required spark for your spark plug.
If no spark appears, check for broken wires, shorts, grounds or a defective stop switch. Once you have confirmed that the stop switch is working, reconnect the spark plug lead.
What causes cylinder 1 to misfire? Various factors, including defective spark plugs and insufficient engine compression, can cause misfires.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Spark plug wire boot grounding out on coil, 96 outback 2.5 automatic, just put new spark plug wires, new spark plugs, and new coil on. ran great for two weeks, now spark is jumping out of boot at coil on one wire, put old coil back on and still does it in the same spot. replaced wires again, and still does it in the same spot. seems to do it only under a load. Is my new spark plug on that cylinder bad? Does the coil need some insulation under it? It is the coil that sits right on top of the motor. Any ideas? thanks.
ANSWER : Sparks are high voltage, and will always follow the path of least resistance. If you can visibly see a spark (whether in a lighted area, or in the dark), that means either that a plug wire (or coil wire) is open (non conductive), or your have a carbon track on the surface where the spark can be seen, but most likely you have BOTH problems!

If you have an ohmmeter, check the resistance of each wire involved, particularly spark plug wires … which means you must be able to connect to both ends of each wire at the same, and hopefully, FLEX those wires, to be sure they don’t have a break inside that is intermittent (comes and goes)!

Read Full Q/A … : Sport & Outdoor – Others

The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.
ANSWER : Get to the manufacturer

Read Full Q/A … : Sport & Outdoor – Others

Trying to install a new fluro light, pull out old light to find 3 reds and 3 blacks 1 copper earth. What do I do to connect it up the right way??? When I pulled the old Fluro light out the 3 Reds were joined together with a connector ,two blacks were joined to one end of light wire, the other to the other end of the light wire,earth wire to the light case,the third black wire was connected to the wire from the ballast? Does this all make sense
ANSWER : No, this does not make sense but I have seen strange wiring before. There is power going from the light someplace else. Just connect it back up exactly as the old light was connected. It worked before so it will work again. If it works it is wired correctly. Without being there to check which wire was the hot wire and which was neutral it is impossible for me to say what is what. Make sure you connect the ground wire to the light chassis.

Read Full Q/A … : Sport & Outdoor – Others

I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.

Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

My 5 hp briggs stopped running. No spark. took recoil off to reveal a rotten coil with wires rotted off. cleaned off the flywheel and replaced the coil with one from Napa. The engine does not have points behind the flywheel. with coil replaced I cannot get any spark
ANSWER : Did you set the Air Gap correctly, it should be .020 inch. If the Air Gap is correct and you cleaned the pickup magnets, you should be getting spark. I have different color coded plastic sheets of the correct thickness to set the Air Gap on different engines. You could use a use a side panel from a plastic soda bottle (Mt Dew, Pepsi, ect) Place it between the Flywheel and the Armature/Ign Coil. Allow the magnets on the Flywheel to pull the Armature/Ign Coil together and then tighten the Armature/Ign Coil bolts. Carefully turn the Engine while pulling the plastic from between the Armature/Ign Coil Pickups. The Armature/Ign Coil is now properly set.

Generall speaking for a gasoline engine to run you need 3 things. (1) Spark, (2) Gas and (3) Air.

I hope this is helpful. UAW 974

Read Full Q/A … : Sport & Outdoor – Others

I have imported a 2000 Compass Herald Clermont caravan from the UK to Australia. The van has two 7 pin round plugs to connect to the towing vehicle. The blach one which has 7 wires is self explanitory but never having owned a van in the UK with Batteries and charging unit I don’t know what the second plug which is on the grey cable does.
Could you please explain what each of the coloured wires (5 in all) connect to on the towing vehicle as I need to wire in a second socket on the rear of my car.
ANSWER : Here is a link to a site which explains all the different wire functions for all the plug types:

http://reviews.ebay.co.uk/How-to-wire-trailer-plug-and-socket-electrics_W0QQugidZ10000000004581261

Type 7 Pin Plug:(12S) (Grey)

Yellow – Reverse Light
Blue – Live Battery Feed
White – Earth
Green – Live Feed
Brown – Spare
Red – Fridge
Black – Second Earth

Hopefully this is what you were looking for.

Please click on the 4 Thumbs Up rating icon if this was at all helpful.

Thank you very much.

Joe.

Read Full Q/A … : Sport & Outdoor – Others

Our bildge pump still puts out 3 amps when off. Bad wiring. Is there a diagram manual of wiring for a 1990 ski centurion trutac III ski boat?
when you get to the harness connection of the wires they change colors.
ANSWER : You can get all kind of bilge pump related documents here: http://manuals-market.com/search.php?cmarque=PERFORMANCE%20TEKNIQUE&modele=ICBM%20779.
Afterclicking this link you will be forwarded to a page contains a form. You need tofill up that form. Most of them are pre-filled. You need to write “bilge”in Brand box and model number in “model number” box. Please don’tforget to mention “type of product” in the “description box”.Finally accept their “terms and condition” and click on “search”tab.
Under “Typeof Document” you will find schematics diagrams. Download documents as per yourrequirement.
Hope this will help you. Good Luck.

Read Full Q/A … : Sport & Outdoor – Others