Sport & Outdoor – Others

Gun was loaded with a bb and pumped 10 times then I accidentally loaded a pellet and now it won’t fire.
Experienced athletes share their insights in answering this question:
Yea mine way difrint its a 760pumpmaster

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Did you know that altitude and pressure will affect your pump gun? Airgun manufacturers will typically impose a one to 10 time pumping maximum on their multi-pump airguns based on standard day conditions and maximum valve pressure. The pump limit is meant to preserve seals, reduce wear and tear and prevent valve lock.
The 880 shoots both steel BBs and lead pellets through its rifled steel barrel. At 10 pumps, Daisy rates the rifle at 715 f.p.s. with lead pellets and 750 f.p.s. with steel BBs.
A single pump would raise welts but not break the skin.
The Daisy Powerline model 35 BB gun takes 3 to 10 pumps to send BBs up to 625 fps (pellets=605 fps). The texture on the grip and pump handle make it that much easier to get a grip and stay on target. Ideal for plinking and target shooting.
A BB with a velocity of 45 m/s (150 ft/s) has skin-piercing capability, and a velocity reaching 60 m/s (200 ft/s) can fracture bone. This is potentially lethal, and this potential increases with velocity, but also rapidly decreases with distance.
Once fully charged, an electric BB gun is capable of penetrating a cadaveric animal model at distances up to 5 m (1 m = 25 mm penetration, 3 m = 20 mm penetration, 5 m = 15 mm penetration).
Gradually decrease your pumping sessions.

If you pump five times per day, eliminate one session so you are only pumping four times per day for the next few days. Give your body those few days or longer to adjust, and then drop another pumping session so you are only pumping three times per day.

The Daisy Red Ryder is perfect for teaching gun safety and marksmanship due to its relatively low velocity (350 feet per second) and manual crossbolt safety.
Pellet and BB guns are high powered and can easily injure or kill a child. They should be used only under adult supervision. The Consumer Products Safety Commission recommends only kids 16 years of age or older use BB guns.
Getting shot with an airsoft BB is generally considered to be a good bit less painful than getting shot with a paintball since paintballs are much heavier projectiles that typically carry far more energy.
The intent of a Two Tone Service is to provide an option to purchase an Airsoft Replica / Realistic Imitation Firearm (RIF for short) for those who are 18 years of age and above and who do not hold a recognised valid Airsoft Defence.
Air guns are BB guns or pellet guns and use compressed air, gas or a spring piston to propel a skirted lead pellet or a copper plated BB. The average maximum effective range of a BB gun is 15 feet and a pellet gun is 33 feet.
A: A BB can kill a rattlesnake if the proper BB gun is used. Since the ammo produces no power. All the power is produced in the air rifle.
In fact, missiles from BB and pellet guns can penetrate skin, eye, thorax, and abdomen and even cause bone fracture.
Blood can be drawn, but injuries that do occur are predominantly superficial. Full-seal protective eyewear (goggles or glasses) is widely considered the minimum protection for airsoft players, as the eyes may be injured by any type of impact.
On bare skin, yes almost definitely. Anything over 350FPS, expect to have marks upon impact with bare skin as well as the feeling of a bee sting where the BB made impact with the skin.
A: Depending on what airgun they are shot from a . 177 caliber steel BB can pierce the skin and break glass. Never fire them at anything you don`t intend to shoot.
Plan to pump 8-10 times in a 24 hour period. Full milk production is typically 25-35 oz. (750-1,035 mL) per 24 hours. Once you have reached full milk production, maintain a schedule that continues producing about 25-35oz of breastmilk in a 24 hour period.
How Long Should I Pump? In the beginning, when you are producing small amounts at each pump session, the session lasts for 10-15 minutes. Later, after your milk has “come in” abundantly, you should continue pumping past when the milk stops to flow for one to two minutes.
That can be up to eight to 12 times in a 24-hour day, or every two to three hours for 15-20 minutes at a time. As your milk supply becomes more established, you may find that you can space out the pumping for longer, at least at night.
Generally, moms should be pumping every 3 hours. Pumping more often can help stimulate breasts to produce more milk. Moms can try pumping both breasts for 15 minutes every two hours for 48-72 hours. Then moms can return to their normal pumping routine. Pumping for longer than 30 minutes may not be beneficial.
That can be up to eight to 12 times in a 24-hour day, or every two to three hours for 15-20 minutes at a time. As your milk supply becomes more established, you may find that you can space out the pumping for longer, at least at night.
HOW LONG DOES THE CO2 CARTRIDGE LAST? ​Once penetrated on the first trigger pull, the CO2 cartridge will last 24 hours or 21 shots.
You can generally load 3 shells in a factory shotgun with a stock magazine tube. This means 2 in the tube, one in the chamber. If your magazine tube has an after-market extension, you might be able to load more rounds.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have a tippmann custom pro with a cyclone feeder. I recently got the SAW stock to put on it and encountered some problems many times after I reassembled the gun. I took it apart at least 5 times before I thought it was fixed but now ive encountered another problem. I believe it has to do with the cyclone feeder not responding or something is out of line in the gun. When I picked up the gun to shoot, no paint came out so I took off the CO2 and the barrel and saw that the paintball was 1/3 inside the gun. I also have a problem when im shooting it sometimes does really fast burst. Thank you
ANSWER : Hi there. Tippmann markers are super tough to make sure that they are put back together properly. The stupid clamshell design plus all the little, under engineered parts make it difficult to get it back together properly, especially after installing a stock. I was in the paintball industry for 10 years but have been out of it for a little bit, but i was one of the founding members of Uprising Nation and was a gunsmith/ salesman for PaintballOnline.com / Xtremes. Now with that said…I even had trouble with the tippmann 98’s…and I can rebuild an autococker with my eyes closed but can sometimes be stumped by the tippy’s bad design. It is really tough to diagnose an issue on these guns without looking at it. You may have the ball detent backwards,l missing a pin, sometimes the after market stocks on those are a little too large on the outside diameter preventing the internals from properly seating. The cycloce system may be off due to the valves not meing properly aligned or the connecting rod not being in all the way. Many times though it is incorrect installation of the detent or the deternt gets damages. That little orange peice of **** flap is a mance. I would start there.

It may seem like i am bashing your gun. Im not… Once they are put together properly they work great. Just DONT TAKE THEM APART. lol. If you buy the parts at a local gun shop they will install them for free.

lol I have 6 guns for sale 🙂

Have a good day

Read Full Q/A … : Sport & Outdoor – Others

I bought a new mossberg 590 a1 shot gun a month ago, I love the gun but its having a couple of problems, the first problem is that when shooting every once in a while i get sprayed in the face with exuast from shooting through the safety very scary! any ideas whats causing this? how to fix it? second is that some times the fireing pin sticks and the gun will not discharge a round? the third problem is that i have had feeding issues with gun where it will not realice a gound from the tube, ive taken a tip of a knife to the stuck round in the tube and it prys out with little effort, these problems dont happen every time i go shooting, just every once in a while, but they a happening more and more, im conserned cause the gun is brand new, and i wanna be safe while shooting, can you guys help me? any ideas/solutions? please help!!!!!!!
ANSWER : Personally, with that many problems, I’d call Mossberg and get a return authorization. None of these things should be happening, especially with a new gun.

Read Full Q/A … : Sport & Outdoor – Others

Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.

See less

ANSWER : Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up

Read Full Q/A … : Sport & Outdoor – Others

My daisy model 99 bb gun does not shoot bb’s with any force.
ANSWER : Try shooting a ton of silicone oil into the oil hole on the side of the barrel and then leave the gun sitting on its muzzle over night, then in the morning with the barrel out dry fire it a couple of times and then try it. what this does is expand the leather seal and bring back air pressure. it worked on my 99, good luck

Read Full Q/A … : Sport & Outdoor – Others

My gun just beeps when i pull the trigger even when hooked up to hpa.battery is new.last time i used the gun just before it messed up i had it hooked to o2 and it would fire then beep ,i have a anti syphon tube installed to. the air shot out the asa instead of the reg when i took off the tank.usually gun holds air with tank off then you shoot it to get rid of stored air,this time it shot out the asa????
ANSWER : You have probably messed up your solenoid, did you fire the marker straight up with the o2? I would make sure that all of the board settings are back to factory default especially the dwell and reattempt with compressed air. If the marker is still not firing get your hands on a new solenoid for it.

Read Full Q/A … : Sport & Outdoor – Others

I have coleman component 443 camping stove.
While pumping, the input air by the pump leaks just after the pump.
I guess the cap of pump should be replaced.
I tried to buy the part in Vancouver, unfortunately, I couldn’t.
I will visit seattle next week, is there any repair center in seattle?
ANSWER : Yms3023000-The only official Coleman repair facility is in Wichita, KS. Try oiling the flexible gasket at the end of the pump. More often than not, a leaking pump is is due to the gasket drying out and not forming a proper seal.Hope this helps.Regards,DIYpro

Read Full Q/A … : Sport & Outdoor – Others

I have a multifunction sports watch that i bought from Big W, (no brand name)

By accident i set the watch to 24 hour time, originally it was set to 12 hour time, how do i set it back? ive tried every button combo including the button combo i used when i accidently set it on 24 hour time, the instructions only say how to set the time and date, it doesnt say how to toggle between 12 hour and 24 hour time, is there a generic way to toggle it on sparts watches? btw, holding the mode button in does nothing on my watch, no matter how long i hold it in for

ANSWER : Hi. How may buttons do you have, 3 or 4 buttons?if you have the 4 buttons, try this:You need to go through the time and date settings again. The 24 and 12hr format select is at the end of time/date adjustment.To set the time and date:-press the top-left button then right-top button to set the seconds, press bottom-left button to set hour then press top-right button to adjust hour, press bottom-left button to set the minute then press top-right button to adjust minute. To set date, press the bottom-left button then press top-right button to adjust month, press bottom-left button then top-right button to adjust day and finally press bottom-left button to set the time format then press top-right button to select 12hour format. Press top-left button when done.Since you have a generic sports watch, it is hard to write specific instructions to set the time format. If your watch has different ways of setting the time, just remember that the 12/24hour format is usually at the end of time and date adjustment.Let me know if you have questions. Good luck.

Read Full Q/A … : Sport & Outdoor – Others