Eclipse 1100 Hr/A Elliptical

Bike works but e2 comes up as code.bike is used could this just be low battery

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

E – 2 Incorrect code chip Turn off the meter and insert the correct chip. E – 3 Test error Discard the test strip and repeat the test. E – 4. Insufficient blood (or QC. control) Discard the test strip and repeat the test.
The E2 error code is an AUTO-STOP PROTECTION indicating a short or open circuit in the indoor pipe sensor. Unfortunately, there is not any troubleshooting to resolve this error. The unit will require a repair service.
E2 – This indicates a brake problem. The brake wire may not be connected properly. E3 – If you see this code, there may be a motor connection problem to the controller. Either the controller or the motor will need replacing and reconnecting.
The E2 error is displayed on the CID when the weapon detects that the date/time is off. This can occur if the battery has been left out of the device for an extended period of time or that the device has not been connected to Evidence Sync for an extended period of time.
Resolution. Device shows “E2” Cuff is under-inflated or over-inflated.
What it means: Error message could be caused by a used test strip, applying blood to the test strip before inserting it into the meter or a problem with the meter or test strip. Error 2, sub-code 1 can be caused by inserting a test strip which has already been used.
Solution. Error 2 is a network error code produced by Windows NT that generically translates to: “The system cannot find the file specified.”
Whirlpool gold series dishwasher error code e2/ f2, means main control board is not getting correct signal from the user interface. Turn off power/breaker, remove screws holding inner door liner, remove liner and check/secure/clean all wire connections from front interface and main control board.
To get rid of the CODE ERROR E, simply disconnect your battery, wait for a couple of minutes, then reconnect your battery. And there you have it. Your radio is ready for you to enter your code.
E2 — Freezer sensor fault. Issue: The compartment temperature in my freezer is incorrect.
Solutions. E1, E2, E3 – Remove the console and use a soft rag to clean the connector between the console and battery. If this does not work, replace the console. E4 – Replace the motor wheel.
L. First numbers represent the amp hours: 55 = 55AH, 165 = 165AH etc. Next the letter represents the terminal size: D = standard terminal, B = small terminal, E is for long batteries like an N100, F & G is for terminals down one end like N120, N150 and N200.
E1- Electrical components

Try to pull the rubber handle on the handlebar slightly out from the throttle lever, often this error code is due to the rubber grip and the throttle lever being too close. After this you can check that the on and off button in the display works properly.

9: (heat/cool flash): E2: Fault: High or Low pressure tripped (Note: Some models have discharge sensor, which will also give the same fault code.)
If “E2” appears repeatedly, inflate the cuff manually until it is 30 to 40 mmHg above your previous measurement result.
A blood sugar target is the range you try to reach as much as possible. These are typical targets: Before a meal: 80 to 130 mg/dL. Two hours after the start of a meal: Less than 180 mg/dL.
Error message E2 indicates an error in LED lighting in induction hobs, and an error in the temperature sensor in teppan yaki appliances.
E2 – Temperature sensor error. Circuit is open or closed. It means the system cannot read correct temperature of working and results in switching OFF of the cooker. Replace the temperature sensor if the error persists.
a. Close safe door, enter 3-6 digit code and press “LOCK” on keypad. The screen will show “CLOSED” and the door will be locked automatically. NOTE: if the door is not closed properly, the screen will show “ERROR2” and the bolts are retracted automatically.
Error code 2 means that OneDrive has experienced a problem fetching your account details. Sign in to your Microsoft account to ensure there are no authentication issues.
The “Key not found” error (status code 2) indicates a different error condition. For a query operation, this status code is returned by a cluster node if the set does not exist on that node.
F3E2 – Moisture Sensor

The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data. Pressing the `Power` button will clear the error code and allow you to restart the machine. If the problem persists, call for service.

An E2 error is shown when no contact is detected between the motor and the valve pin. To resolve this, please make sure that the mounting bracket and the adapter (if used) are attached properly to the radiator.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

What does a E2_C error code mean?
ANSWER : If the console doesn’t receive a signal from the speed sensor, which is mounted on the back of the motor, the console stops sending power and displays an E2C error code.

You need someone to test voltage on the treadmill and determine if the power supply board, motor controller, or motor is bad.

You can have it repaired with “Sears Treadmill Repair” (even if you bought it somewhere else) calling them at 1-888-206-3131…

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

Edge 491 exercise bike monitor panel dead
ANSWER : Http://www.academy.com/images/pdf/Fitness_Quest/Edge_Recumbent_Bike_491r.pdfMine went dead last Spring. I ordered a replacement part from Fitness Quest. I think the link is above. Actually, while I was waiting for the part, I reconnected all the wires on the whole bike and the panel worked. So I actually have an extra new working panel if Fitness Quest doesn’t have the part for some reason and u want mine. Double check ALL the connections of the wires first. They come loose easily.Nancy

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

How to read Yamaha Neos etc Fault Codes
ANSWER : No codes here but it might come in handy. http://scootergrisen.dk/scooterhjemmeside/download/yamaha_neos_2t_servicemanual_2.pdf

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

I have installed my Garmin Edge Cadense Sensor, followed the instructions and seems like both the crank arm and wheel sensors are ticking and sensing. However, the edge does not seem to receive the cadense data. The display remains blank. What could be the problem? Batteries?
ANSWER : There are two tests

705 first – settings, ANT+sport, accessories, check that cadence sensor is set to YES

press the reset on the cadence sensor and rotate the cranks – the LEDs should flash every time the magnet passes the sensor. if not its the position of the magent relative to the sensor that needs adjusting.

Hope that works
😉

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

I have a treadmill Nautilus 516, I mark an error e7 flashing. I already unplugged, lubricated, and clean the speed sensor with alcohol and a clean head cotton. When I jump in at the front it locked out like when you put it in position for move it. When I put start in 4 seconds get the error e7; and when the error still the jump in the front and locked if I put in the back of the walking part do not locked out but still get the e7.
ANSWER : Hi,It stands for a lost signal in the console wire harness. It could be one of the wires has been broken or there is a connection loose. unplug and replug all connections. Then check for continuity in all the wires in the harness. Try to enter the service mode, press Stop Belt, Faster, and Slower
simultaneously. P000 appears in the Select display, indicating that no
key is pressed. To exit the service mode, press and release the same three keys simultaneously or press Power twice to power up into normal mode. Check
the speed sensor to make sure it is within 3-4 inch from the front
roller (magnet). Then check the sensor wire harness to make sure it is
fully seated on the lower control board. If the problem persists, then you need to inspect the machine properly as it could be a faulty console/control board /speed sensor.Let me know,if needed further assistance.Hope i helped you.Thanks for using ‘ Fixya ‘ and have a nice day!!

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

Error code E5-5
ANSWER : I didn’t use mine for several years then just started again. It stopped after 15 minutes so I read the manual and used a silcone lubricant on/under the treads as recommended. That definitely helped and it was working again quite well for about a week or two. Now I get the error 5 again. Wondering if I needed to add MORE lubricant the first time so I am going to do it again tonight. Maybe it is the roller pully that needs the lubricant. Who knows. I just want it to work!! I am determined. 🙂
-becky

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical

HI!
I continually get code 90 (low/NO flow) from my 8111. I have disassembled, cleaned EVERYTHING, including the inlet port AT the pump (remind everybody to check this as stuff gets past the filter basket and will plug the pump inlet).

There is No air in the system and I get superb pressure at the outlet, yet I still get code 90. I again removed the flow sensor and put my ohm meter across the flow sensor terminals and activated the flapper and measured an open circuit. I used a heavier magnet to see if I could get make the internals of the sensor move to get an ohm reading, but I get nothing but an open circuit, ie: no measured resistance.

Can I simply bypass the defective flow sensor to trick the 8111 to think it has full flow without damaging the ‘brain’ of the system.?

Intex corp is useless at these questions. They have been out of stock on this sensor for months and are telling me “two weeks” for two months and now it’s “end of August” which I do not believe. Meanwhile I am making no chlorine while the 90 code is showing.

I love the 8111, this is the first problem I’ve had with it, and I’m frustrated that I can not get such an important part from them.

Thanks for listening!

ANSWER : Have you been able to find a solution to this problem. I am having the same issue.

Read Full Q/A … : Eclipse 1100 Hr/A Elliptical