[SOLVED] Coleman Propane Camp Stove Won't Light

2 Burner Propane Stove 5430E700

I can’t hear any propane getting to the stove when I turn it on but the propane lanturn attached to the same tank works fine.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

The problem of an appliance not lighting is usually caused by one of two things. Either the generator is clogged-up with soot, or the fuel & air tube is blocked by dirt or varnish. Lanterns. (go to stoves) Give it 30 or 40 pumps to really pressurize it well.

If your stove is not cooking properly, it is most likely not delivering enough fuel to the burners. Diagnose the problem by finding the point in the system where the flow of gas is obstructed, or the place where the system is not sealed. Remedy it by removing the obstruction or sealing the leak.

The most common (in my experience) cause is the collection of dust and/or bugs in the gas tubes and burners. When the propane bottle is full it has slightly more pressure and can overcome developing issues. As the supply of fuel gets lower, the pressure drops slightly, and the flow of gas decrease.

Soak the sealed burner base in vinegar or warm water and use a stiff brush to remove any debris. Finally, clean any remaining debris out of the burner holes with a toothpick, sewing needle or compressed air. Reinstall the burner, cover and the grill, and try igniting the burner once more.

Sometimes when you try to ignite the burner, you can hear a clicking noise and see sparks, but the gas doesn`t ignite. The reason this happens is that the gas supply is partially blocked.

Check for loose or burnt wiring

The stovetop will need to be lifted up to check the wiring and connectors for damage. If the wiring or connectors are damaged, they will need to be replaced. A loose connection could also be causing the burner not to work, so you should check that the connectors are not loose as well.

Coleman® stoves, lanterns, lamps and irons use the same basic principles of operation, and have since the early 1900s. Pressure devices place and maintain their fuel under pressure, convert that fuel to a gas vapor and then control the manner and rate at which it burns.

Your Gas Valve Needs Attention

The gas valve on your furnace delivers the gas your pilot light needs to remain lit. If the valve is turned ON, but your pilot light won`t stay lit, the problem might be a broken gas valve. The solution most likely will be to replace the valve.

Make sure the bulb is the problem.

Check and make sure that there`s power to the oven—maybe it came unplugged or a circuit shut off. You can also check to see if the problem is the switch located inside the oven door, the one that signals to turn on the light when you open the oven.

Sometimes when you try to ignite the burner, you can hear a clicking noise and see sparks, but the gas doesn`t ignite. The reason this happens is that the gas supply is partially blocked.

They are all good. They are much better than the originals and will last you the rest of your life. I exclusively cook on Coleman stoves, and my standard thing is to get a new stove, clean out the fuel tank, replace the pump leather and cap gasket, and just use. Occasionally, the stoves need a new generator.

Make sure the bulb is the problem.

Coleman Propane Lantern

propane cylinder will power the lantern for up to 4.3 hours on high and 9.25 hours on low.

Make sure the bulb is the problem.

Sometimes when you try to ignite the burner, you can hear a clicking noise and see sparks, but the gas doesn`t ignite. The reason this happens is that the gas supply is partially blocked.

If your electric stove burner is not working, it could be due to a loose connection between the receptacle and burner terminals. You may be able to tell if the terminal is loose by wiggling it, but nonetheless, you might as well unplug it, check the terminal for damage, and then plug it in again.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

My bike won’t start after jump starting it, putting in gear it went dead & now the neutral light won’t shine.
& won’t start

ANSWER : Sounds like you fridge seilanoid try jump in across it with a screwdriver

Read Full Q/A … : 2 Burner Propane Stove 5430E700

I have lost all pressure in my coleman 502 camp stove. It worked well a few times but up camping it lost pressure after having worked well making coffee but after getting back to camp after a trip out fishing its like someone messed with my stove while I was out. Could it have overheated sitting out in the sun on our table? It no longer builds up pressure when pumped. I took the part out and the plunger looked worn, but I don’t know if it is missing a part inside the tank or what. I just bought it at a thrift store a couple months back as an extra burner.

ANSWER : If you didn’t oil it it might do that. or you should check the position at witch you are holding the plunger.
the instructions say that the plunger turns left and right but mine doesn’t do that
DON’T FORGET TO COVER THE HOLE IN THE PLUNGER THOUGH
IT TOOK ME A WHILE TO FIGURE THAT OUT THE FIRST TIME

Read Full Q/A … : 2 Burner Propane Stove 5430E700

Coleman 425 2-burner white gas stove pops out flame on low heat

ANSWER : There is water in your fuel. Drain the tank and flush it out with denatured alcohol. Refill with fresh fuel.

Read Full Q/A … : 2 Burner Propane Stove 5430E700

Trying to install a new fluro light, pull out old light to find 3 reds and 3 blacks 1 copper earth. What do I do to connect it up the right way??? When I pulled the old Fluro light out the 3 Reds were joined together with a connector ,two blacks were joined to one end of light wire, the other to the other end of the light wire,earth wire to the light case,the third black wire was connected to the wire from the ballast? Does this all make sense

ANSWER : No, this does not make sense but I have seen strange wiring before. There is power going from the light someplace else. Just connect it back up exactly as the old light was connected. It worked before so it will work again. If it works it is wired correctly. Without being there to check which wire was the hot wire and which was neutral it is impossible for me to say what is what. Make sure you connect the ground wire to the light chassis.

Read Full Q/A … : 2 Burner Propane Stove 5430E700

Razor E-100 – The toggle switch was broken, I replaced it with another lighted switch, but the switch won’t light. The motor runs o.k., why won’t the switch light when turned on? Thanks.

ANSWER : The Switch can be almost any but the lighted switch has to be a compatible 24vdc lighted switch.
As seen on this web page.

SWT-105

Razor E100 and E125 Electric Scooter Parts ElectricScooterParts com

Read Full Q/A … : 2 Burner Propane Stove 5430E700

Hi, my tiger river spa does not heat. Filters are clean, jets work, no light installed. On ciruit board, green light for “Lim” , red light for heat, no other lights. Just bought house one month ago, no manuals.
Spa is a Bengal. Have noticed a symbol (can’t tell what it is) on the screen then most of screen goes blank with just the power light on. Is there a vacation mode or something like that?
Thanks for your help.

ANSWER : Spa’s are such that so many components can become faulty when left unattended to over a period of time. But most likely what your unit needs is just a regular service to clean up its systems and also ensure there are no leakages in the pipes. Bengal is a wonderful and durable product.The problem could range from low power supply to wires being eaten up by rats and other pests. Also it could be burnt out heaters thereby the inability to produce heat. The indicator on the screen could mean various things but the screen going blank usually would be caused by poor power supply.If you dont have the technical know how refer an expert to check it out and ensure the exact problem of the above mentioned is wrong with it before repairs can be carried out.Hope this solution has been helpful?

Read Full Q/A … : 2 Burner Propane Stove 5430E700

I would like to hook up a 12 volt battery to the trailer. In the cupboard below the propane stove is a plug with white, black and orange wire to it.
In the AC power converter cupboard I have a plug with a black and orange wire. How do I hook up the battery so that it charges and runs the fridge while I’m driving, and lets me use the lights with the fridge on propane while I’m camping?

ANSWER : You haven’t told us what trailer you have, what DC-AC converter you have, it the wire is original or aftermarket and what gage it is.

Because of that you must first identify the wires. You will need a multimeter for that. Start by finding if your trailer has a negative wire or is using the chassis as the ground. For that disconnect the battery from the truck (make sure you have the radio code handy) then measure the resistance between the 3 wires and the body of the truck – you will find the ground wire when the resistance will be close to 0. Reconnect the battery and measure the voltage between the ground wire and the other 2 – the one with 12v on it is the power one and the other goes to the power input of the converter. Check that by removing the converter and looking where they are plugged – if you have any doubts that they are not the wires from the cupboard just check their continuity.All of this is a 5 minute job. Once you know the wires just connect the ground on to the minus and the power and the converter ones to the plus.

Read Full Q/A … : 2 Burner Propane Stove 5430E700