nd took it apart and put it back together it was working fine again and i didnt make any repairs at all.
98 Custom Act Paintball Gun
Experienced athletes share their insights in answering this question:
You are correct. Cold (and heat) play a part in expanding the parts of your marker. In cold weather, plus the coldness of the co2 working through it, the various parts can and will expand and contract at different rates. It only takes a fraction of inch to leak.First thing is to make sure you have thoroughly cleaned and LUBED your marker. Lubrication… what kind of oil are you using? Some general purpose oils may work well enough in better weather, but in cold weather, and especially when using co2, you would be well advised to find and use an oil specific to paintball markers. These are manufactured with COLD in mind and will continue to work where others will gel up.So yes, you are correct in your assessment. Keep your marker covered up when you’re at the staging area… uncover it to chrono or test fire it at the range.. or when you get ready to roll out to the field. Use a good, paintball-specific lube (and keep it clean and lubed).Also… an o-ring isn’t just an o-ring. They have different densities and much like the proper lube, you need o-rings that are specific to the task at hand. Cold is a killer and it loves to mess with rubber and plastic. An o-ring that’s become hard and brittle can’t do a good job, so don’t get o-rings from just any old place because they’re cheap and look like they’ll fit. Use good parts, good lube, and you should get some better performance out there.Good luck… play hard, play safe, play with honor!:o)
How to Identify and Resolve Common Issues ?
We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :
and in general the problem is it`s too tight or too loose. so it`s a standard flat screwdriver almost guns and generally you`ll find this valve. just needs to be hand tight literally.
If you are still using a CO2 tank on your marker, winter weather is the worst time to play paintball. The cold decreases the pressure that cuts the velocity. Your gun will malfunction making a long, drawn out, putting sound. The marker will frost up and white puffs of vapor will expel from the barrel.
Wrap up: It may get cold out there in the game zones so we strongly recommend layering up in some warm, weather-proof clothing. Most customers bring a large warm jacket, a warm hat, gloves and wrap their feet in a couple of pairs of warm socks and some thick shoes.
Dry Firing PCP and CO2 Air Rifles
Dry firing PCP or CO2 air rifles will usually be completely safe, as there isn`t a piston to worry about. You`re simply releasing a short spurt of air/CO2 to force the pellet up the barrel.
Cold doesn`t just affect the gas used in your airsoft guns, but affects the actual airsoft guns themselves. Metal shrinks in the cold, tightening up tolerances and causing more friction. Liquids become more viscous, meaning lubricants aren`t as effective and provide more resistance. Plastics become brittle and fragile.
Depending on the specifications of your paintball gun, you should get an average of 1056 shots for every KG of CO2 you have.
While playing in the rain, it is also important to protect your paintballs and equipment. Paintballs can turn squishy with just a single drop of water and water can ruin the interworking of a marker. If you bring your own paintball gun, you can wrap tape around the grip frame of your marker.
Dripping or leaking from the nozzle tip when gun is not triggered: This means that the needle and nozzle are not seating correctly. This can be due to wear & tear, damage, clogging or debris. Remove the nozzle and make sure there is nothing in it that would prevent the needle from seating.
While it completely depends on the individual child, it is generally recommended that ages 12-to 14-years-old is the proper age to begin the sport of paintball. Most children at that age are able to understand and abide by the safety rules while still enjoying the game and not overreacting to getting hit.
It`s an intense, challenging, and fun game (not to mention a great workout). I love it when girls show up and prove that we can play just as rough as the guys. However, I won`t deny that there are some key differences between the genders.
“Around 350 feet per second is a figure you want to keep in mind,” says Beeman. “At 300 to 400 fps, that`s where penetration occurs in a human skin. Below 350 fps, it is generally considered capable of only limited harm. Above 350 is considered very harmful or lethal.
HOW LONG DOES THE CO2 CARTRIDGE LAST? Once penetrated on the first trigger pull, the CO2 cartridge will last 24 hours or 21 shots.
What happens with airgun CO2 when the temperatures dip down below 65 degrees Fahrenheit is that it freezes the air gun valve much faster than it would otherwise. A frozen valve means no control on what is going through it. In much simpler terms, the BB gun stops working. That`s really about all there is to it.
All CO2 guns eventually start to leak over time. You have control solely over the rate of loss which thankfully can be minimized by fixing the leakage. Besides just replacing the bb gun gas canisters, there are other ways through which you can fix the leak.
Reliably Powerful – Each 12g CO2 cartridge can deliver a minimum of 30 shots and a maximum of 200 shots, depending on the C02 powered device you use. However, these CO2 cartridges 12 gram can give you 20 to 30 good shots at once.
CO2 will hold up better than propane/green gas, but you probably won`t get much use out of it in sub 30°F weather. It`s also not like an on/off switch. Depending on the temperature, you`ll start to experience a gap between pulling the trigger and it firing and, at colder temps, it just won`t work. No problem.
What`s the Risk? Those who do not wear eye protection are at risk of eye injury, according to the AAP. Airsoft pellets that strike the eye can cause scratches, painful pooling of blood inside the eye, lens dislocation or blindness. The AAP recommends that kids use paintball-style protective eyewear.
Also known as Nitro, N2 or Nitrogen tanks, these models come in a range of sizes – typically from 3000 PSI to 4500 PSI (the higher the pressure, the more shots are possible). The main advantage of compressed air is that it will perform more consistently than CO2, especially during high-speed shooting.
Both Co2 and Compressed Air tanks are made out of aluminum and are most often black in color. However, only Compressed Air tanks are wrapped in Carbon Fiber. If your tank is Carbon Fiber wrapped then you have a Compressed Air tank.
Therefore, carbon dioxide is 1.5 times heavier than air.
Are Paintball Sized 20oz CO2 tanks food grade, or do they contain residual oils and metal shavings from the manufacturer? In short the answer is Yes. They are originally manufactured for paintball use, but have been cleaned so that they are safe to use for food and beverage use.
NO. Paintballs are water-soluble, non-toxic, hypoallergenic and biodegradable. Any paint marks will wash out of your clothing in a normal wash cycle. Paint on your skin and hair will wash out easily during a shower.
Yes, paintball is an all weather sport. Many people prefer Paintball in the rain as it adds to the adventure and is awesome fun so leave your umbrella at home and bring some good sturdy footwear.
Going back and forth to refill your CO2 tank can cost considerable time and money that will quickly add up. However, if you have access to a compressed air system, you won`t have to worry about making these CO2 refill runs anymore. An air compressor can help refill your CO2 tank, helping save you time and money.
Discover Relevant Questions and Answers for Your Specific Issue
the most relevant questions and answers related to your specific issue
The Bike Technicians Tactic Phase1 An electrical inspection on the bike should produce results. First, the bike battery powers the entire lightening systems mentionable as ignition, meter readings, head lamps, signal indicators. However, the battery provides the power supply to several entities though also significant is the fuse box containing circuit protection coils. Inserting the bike key into the ignition to perform start mode displays the capacity power circuits. A charged battery should display an indication in the meter reading area also known as bike dashboard grading. A malfunctioning start mode on inserting key in ignition may be traceable several locations on the electrical circuits. Attempting to repair the electrical power of the bike usually requires batter power power test kit. The test kit ascertains the battery power making possible progress to the remaining electrical circuits. Test kit also ascertains the fuse box circuit functionality either with fuses still intact or extracted allowing for the next progress level. An observation tour of the bikes electrical wiring kits from battery hold through fuse box compartments to each lightening display area either headlamps, indicators, and meter reading should produce results of any visible damages that may require repairs after the electrical inspection has been performed. Once any faults were observed on the electrical channels, repair mode is the next level. A dull battery either may have been depleted completely of durational capacity requiring another for replacement. Alternately, a depleted power supply due to prolonged storage may require charge functionalities. Usually, a device capacapble of restoring a battery of electrolytes is resorted for charger ability. The type of battery may require constuents either liquid cathode replenishment in the battery entrapment area prior to charging feature is assumed with electrolyte machine. Once the battery has regained full functionality makes way the next repair task. The fuse box may have simply required replacement fuses either as missing or burnt out. A fuse box usually contains additional spare for replacement functionalities. An alternate arrangement at acquiring fuses on the auto mart may replace the burnt devices. The next electrical task is wiring fixtures achievable by mending broken cords with appropriate electrician’s tapes else malfunctions may remain. Alternately, a worn-out electrical wire is replaceable by acquiring the entire extension lengthwise between significant areas. The last remaining electrical units are lightening indicators consisting of bulbs or luminescent displays reflectors. Observe the blub areas either by loosening covers to inspect for observable burnouts else the entire electrical circuitry is ready for functionality observations with separate entities. Engine Technicians Tactic PHASE 2 A bike engine inspection includes observation for indications of malfunction. Any fluid residue is indication of problem areas. Where oil leaks usually requires engine block inspections. A bike engine consists of an entrapment compartment where mechanical combustion takes place. First, the entire observable block consists of an external coating known as engine bloc housing internal component of pistons, rings, and fastens known as cylinder heads. A bike engine has every component embedded within requiring technical expertise to achieve an inspection. Once deciding on the engine task requirements, acquire a tool box with the appropriate componements as first requirement before engine works is commence able. Second, the bike may require an area environment as workshop requirement to attain engine inspections. Third, bike engine are least bulky compared with vehicle engines however assistance would complement the inspection phase. Prior to inspecting the bike engine, a strap mechanism has to be assumed to achieve expert maneuverability also as safe precaution. Unless parts hinder maneuverability at engine locations, the only removable components should be the engine. First, start with disjointing the spark plug cables to acquire accessibility to plugs imbedded on the cylinder heads. The plugs require tools to loosen thereby exposing the combustible area. Once the spark plugs are exposed, two alternatives are likely. First, a spark plug may have gathered rust residue only requiring cleaning to attain regular capacity. The pin area of the spark plug may have been twisted due to overheating and slight melting dislocation. Usually cleaning the residue from old plugs may simply expose the ignitable capacities. However, an observation of twisted plug pin may require twisting back in place to achieve full ignitability once bike engine starts. A bike engine bloc has the pistons as combustibles or blasters of fuel gasoline. The rings perform as strap fasteners whenever the pistons move about combustibility. Usually, the engine entrapment components would have collected residue requiring clearing. Also, pistons together with rings may require replacements either as worn-out due to prolongs tasks or overexerted biker features.
Get to the manufacturer
I have a tippmann custom pro with a cyclone feeder. I recently got the SAW stock to put on it and encountered some problems many times after I reassembled the gun. I took it apart at least 5 times before I thought it was fixed but now ive encountered another problem. I believe it has to do with the cyclone feeder not responding or something is out of line in the gun. When I picked up the gun to shoot, no paint came out so I took off the CO2 and the barrel and saw that the paintball was 1/3 inside the gun. I also have a problem when im shooting it sometimes does really fast burst. Thank you
Hi there. Tippmann markers are super tough to make sure that they are put back together properly. The stupid clamshell design plus all the little, under engineered parts make it difficult to get it back together properly, especially after installing a stock. I was in the paintball industry for 10 years but have been out of it for a little bit, but i was one of the founding members of Uprising Nation and was a gunsmith/ salesman for PaintballOnline.com / Xtremes. Now with that said…I even had trouble with the tippmann 98’s…and I can rebuild an autococker with my eyes closed but can sometimes be stumped by the tippy’s bad design. It is really tough to diagnose an issue on these guns without looking at it. You may have the ball detent backwards,l missing a pin, sometimes the after market stocks on those are a little too large on the outside diameter preventing the internals from properly seating. The cycloce system may be off due to the valves not meing properly aligned or the connecting rod not being in all the way. Many times though it is incorrect installation of the detent or the deternt gets damages. That little orange peice of **** flap is a mance. I would start there.
It may seem like i am bashing your gun. Im not… Once they are put together properly they work great. Just DONT TAKE THEM APART. lol. If you buy the parts at a local gun shop they will install them for free.
lol I have 6 guns for sale 🙂
Have a good day
I attempted to put a car stock on my Tippmann 98 custom and took apart the gun but the stock didnt fit, now when i put it back together and shot it with my tank connected the gun wont stay cocked and little CO2 is coming out with each shot the sound is very low as opposed to my other Tipmann 98 custom where its loud and stays cocked. What do i do?
Check the O rings on the big metal striker, make sure that you have the spring on the back (where the stock would have went) in the right hole on the back plate. Make sure that your velocity is set to a reasonable level.
My paintball gun dosent want to shoot i filed up a co2 tank and it wont work. i used it once before this and it worked fine. could it b that the co2 tank dosent work any more? but i berly bought it 2weeks ago.
Tanks just hold air they dont do much else. if the gun cocks and wont fire then id say you need to make sure your trigger isnt stuck
I own a tippman a5 with an UMP shroud and fake metal clip. I took apart for some maintinance and ever since i put it back together its been acting like im out of air after 2-3 quick shots. I took it apart to check it and everything was ok. So i screwed the tank back in and now i have a small leek on tthe nutin between and the tombstone.
What do you think the problem is (im afraid their two different problems).
There is an O-ring up in where the Tombstone slides in. That O-ring has to be lubed (oiled)
and should be toward the rear of the gun when installing the Tombstone. Also, drop-off
in firing can be caused by lack of lube on the internal O-rings. 2 drops of oil in the inlet hole
where your bottle screws on and then dry firing to cycle the oil thru might help. You may need
to completely tear down the gun and clean and lube the internal O-rings. If you can switch to
air AKA…HPA (High Pressure Air) it will be better for internal parts and better consistency overall.
Here is your manual for reference.
Mar 12, 2010 – Could it be the check valve? I took it off and the flap appears to be working correctly. This well has been here a long time. Never given me any problems. I do have galvenized couplers on the discharge and intake sides. Old. Could these be leaking even though they show no sign of water? The discharge is able to hold 30 pounds easily overnight. I do not hear any vacuum in the intake when I take it off. Could the pipe to the well have a leak? I know I would have to insert a sleeve bnut I do not want to go through the hassle if I do not have to. I had put on a brand new pump from the hardware store that did the same thing so I think that would elliminate the pump as being the problem.
Mar 12, 2010 – I have a 3/4hp flotec convertible jet pump. It is able to hold 30lbs pressure on the discharge side as the primie easily for 24 hours. It is not able to pull water from the well whcih has been here for years. i disconnected it for the winter and rehooked it up. The galvanized couplers on the discharge and pump side are old but do not appear to be leakeing as I taped them well. The check valve seems to be functioning well as I took it off and the flap works correctly. The well is not pulling watrer. there does not appear to be a vacuum on the check vale when I losen it. could the check valve be bad? I am aware I might have to resleeve the well, but do not want to hassle with this if I do not have to. I want to eliminate everything else first. i put another brand new pump on it to see if it was that. That partiuclar pump which was the same thng did not work either.
Your well has gone dry it seems. It has happened to my before. At first the new pump I purchased that did not pump I took back for exchange and still no water. I finally gave in and called the well experts and I was told the well was dried up
My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.
I’ve had the same experiance. On my fifth one as well. Fail every year. No idea why.