76075 / 377284 – located in pickwick dam tn area – need service?
Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

The control System checks the water temperature for a reading at or below 60ºF(15ºC) If an error is detected, the topside control will display the code “FC” this means a potential freeze condition has been detected (the spa temp is below 60ºF(15ºC).
FL1/FL2. This code means any of the following: the flow switch is malfunctioning open (FL1) or closed (FL2), the filter cartridge needs to be changed or cleaned, or there is an “air lock” condition at the circulation pump intake.
When FL2 code starts flashing it means the flow switch isn`t working and it is stuck closed. In both cases, the spa heater will deactivate. In both cases, the spa heater will deactivate and main pump # 1 may do the same.
This error is signifying a fault between the compressor and external PCB. To fix the error code you need to do the following: Check the connections between the compressor & PCB and clean and tight. Check for any damage to the PCB, burn marks will show a faulty PCB.
A hot tub flow error suggests that there`s a problem with the flow of water through your hot tub heater. Some of the most common codes are FLO, FL1 or FL2 for flow or pressure switches. The most common causes are a dirty or damaged filter, low water levels, air in the piping system or a faulty pump or sensor.
In computing, an error code (or a return code) is a numeric or alphanumeric code that indicates the nature of an error and, when possible, why it occurred.
A flow error on your hot tub is a sign that there is an issue with your water flowing through your heater in the hot tub. You can identify a flow error as it will display “FLO” on the front panel. Some common issues that can cause a flow error are: Lower than normal water levels.
Is there an E02 error code displaying on your Lay-Z-Spa pump? This means your Lay-Z-Spa pump is experiencing a water flow issue.
Hold down the On / Off button on the pump for 5 seconds. Press thermal reset button (See picture for location of reset button on the final page) Press heater button – pump should be working with no error codes.
(The CF display code means filter-cleaning reminder.) Please check your air conditioner model below and follow the how-to guide to clean the air filter. This will give you cool and fresh air.
Begin by turning the power off to the heat pump. You will need to reset both units by pressing the buttons or flipping the switches. If your heat pump does not have a reset button, it will have a power switch. Turn the switch off, wait for two to three minutes, then turn the switch on again.
Communicating Thermostat for Fan Coil Applications (FC)
When the inverter is switched on, it only comes on for a few seconds then starts beeping with F5 on the LCD display. This is usually an indicator of a blocked fan.
As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.
Symptoms of Spa Pump Failure

There are several signs of hot tub pump failure: Humming noise from motor not turning, frozen shaft, bearings or impeller, or defective starting capacitor. Whining noise from worn bearings. Leaks under the pump from a failure of the pump seals.

Use Quick Actions to fix or refactor code

Or, when your cursor is on the line with the colored squiggle, press Ctrl+. or select the light bulb, error light bulb, or screwdriver icon in the margin. Visual Studio then shows you a list of possible fixes or refactorings you can apply to that line of code.

There are three types of errors that are classified based on the source they arise from; They are: Gross Errors. Random Errors. Systematic Errors.
Error 5 Solution – Check spa cover is not resting on topside panel buttons causing jet pumps to start when cover is on. Error 5 Solution – Use keylock function to lock keypad buttons when spa is not in use. Error 5 Solution – If the problem persists, please contact Spa World™ customer support.
Error 7 (“STUCK RELAY”) – Stuck Relay

This error indicates a problem with the heater control circuitry inside the unit. Contact your spa pool supplier.

In the home security industry, FC stands for “failed to communicate.” The error code may display differently on your panel if it has an alphanumeric pad, but the message simply means that your security system isn`t communicating well or at all with your designated security company`s alarm response center.
(The CF display code means filter-cleaning reminder.) Please check your air conditioner model below and follow the how-to guide to clean the air filter.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need the wire diagram to rewire my Ariens lawnmover to bypass the safety switch. It is Ariens GT-19 model # 931026 Serial # 001463.
Can you help? It is an old Ariens mower but still runs good but now I need to bypass the safety switch in order to run it any longer. The local Ariens dealer said I need to go through the internet and get the wire diagram as they cannot give it to me directly. They told me I needed the wire diagram and the part involved in bypassing the safety switch. Hope this is all the information you need to help me.

Thank you. Roger Fielitz

ANSWER : Here is owner manual:http://apache.ariens.com/manuals/030305C.pdfusually the switch is behind the ignition, sometimes at the N position of gearshift, just look for a switch with one wire coming in & one going out (usually the same color); disconnect the two wires & jumper them together to bypass the switch. Looks like yours has one under the seat.

Read Full Q/A … : Sport & Outdoor – Others

Heat pump wiring
ANSWER : Yes i can , you need to hookup the r and the o together so that the reversing vvalvce is allways energized . so with that im mind send r,y,c,o to theout side unit. at the ahu you’ll hook up the 5 wires for the furnace, r g w1 w2 com and at the thermostat r,w1,w2,y,g,com,o then you will be set (the o get hooked up to o and goes straight out side.

Read Full Q/A … : Sport & Outdoor – Others

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.

Read Full Q/A … : Sport & Outdoor – Others

I have a 1997 Coleman 107 Hot Tub. While filling the tub it over flowed and the circuit breaker popped. Over the years I’ve done this a couple of times. I remove the side, let things dry for a day or so and everything is fine. This time, I reset the breaker and the spa went on. The pumps work fine, and the control panel shows the temp and the indicator light shows the heater is on. However, work never heats up. The local spa repair folks are crooks and they know less than I do, and I know NOTHING. Nonetheless, I’m going to try and fix the problem myself. Now, I need to know the best way to determine if the problem is the circuit board or the heater itself. I also need to know where I can get a repair maual. I’m tired of paying Goober and Gomer hundreds of dollars.
ANSWER : Check the terminals that lead into the heating element to ensure voltage is present (110 AC) if voltage is present upon start up the heating element must be replaced if no voltage is present is is most likely a control board issue. Go to this web site for contact info and possible repair manual aquisition.

http://www.spaguts.com/SpaHeaters.aspx

Read Full Q/A … : Sport & Outdoor – Others

My lg optimus f3 wont read any simcard
ANSWER : You should take it to LG Service Center.

Read Full Q/A … : Sport & Outdoor – Others

I own a Maverick model 88, 12 gauge shotgun. Need plug
ANSWER : The plug is ussaly no more than a wooden dowel that fits inside the spring and is the approx length of the shells put end to end like they would be in the tube

Read Full Q/A … : Sport & Outdoor – Others

Hi, my tiger river spa does not heat. Filters are clean, jets work, no light installed. On ciruit board, green light for “Lim” , red light for heat, no other lights. Just bought house one month ago, no manuals.
Spa is a Bengal. Have noticed a symbol (can’t tell what it is) on the screen then most of screen goes blank with just the power light on. Is there a vacation mode or something like that?
Thanks for your help.
ANSWER : Spa’s are such that so many components can become faulty when left unattended to over a period of time. But most likely what your unit needs is just a regular service to clean up its systems and also ensure there are no leakages in the pipes. Bengal is a wonderful and durable product.The problem could range from low power supply to wires being eaten up by rats and other pests. Also it could be burnt out heaters thereby the inability to produce heat. The indicator on the screen could mean various things but the screen going blank usually would be caused by poor power supply.If you dont have the technical know how refer an expert to check it out and ensure the exact problem of the above mentioned is wrong with it before repairs can be carried out.Hope this solution has been helpful?

Read Full Q/A … : Sport & Outdoor – Others