Stockholm Indoor Table Tennis Ping Pong Table

We are stuck on step #13 for the outdoor table (end leg cross brace assembly). We cannot get the bolt hole on the cross brace (the part with the bent “arm”) to line up with the bolt hole on the table leg. We tried to extend the table leg and table half down and then brought them back in o see if we could get the holes to line up (seller's suggestion), but this did not work. In the process, the table popped out of the plastic carriage in which it sits and was difficult to put back in. The other table half popped out as well and would have slammed to the ground had we not caught it. What cou

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Enlarging holes or aligning mismatched holes in metal is the job of a tool known as a reamer. The process by which this is done is called Reaming and differs from traditional drilling as it requires an existing hole, or holes, as a starting point.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Need a Popeil Pocket fisherman manual
ANSWER : For the original pocket fisherman. I believe the design has not changed. Once you do it the first time it is actually quite easy.Two things to note. Read this whole thing first.1) the location of the bail spring (Keeps the metal bail cover up so line does not get stuck when casting.Note: This is important cause the metal bail cover must rise enough so that the line casts smoothly. (A complaint about this product. But when calibrated correctly it is quite good for what it is)2) The little **** that the crank gear plastic housing will fit into (Must be on top when you put the whole bail back in. The crank shaft lip fits into that ****.You’ll get it when you see it.Remove the panel screws (2) as you did. Pop out the crank shaft (copper). **** is in top when replacing. (remember that). Remove the bail. On the top of the bail there is a screw. ( becareful and remember how the little metal bail spring in situated here. Turn upside down with metal bail cover in your palm as it conects to the bail spring). Pull off metal bail cover. The plastic line holder actually comes apart and holds a lot more line than you think. Replace line. Feed the line back up the rod. Assemble the opposite.

My bike won’t start after jump starting it, putting in gear it went dead & now the neutral light won’t shine.
& won’t start
ANSWER : Sounds like you fridge seilanoid try jump in across it with a screwdriver

My line won’t rewind on my Shakespeare Encore reel. After casting, the bail snaps in place, but when I reel in, the line won’t reel in. The spool turns with the bail, but doesn’t retriev
ANSWER : Your line is on the wrong side of the bail. Rethread the line so its over the bail so that after the cast you flip it up it catches the line and retracts it.

This is the izh 513m .177 rifle. It’s brand new. I am not sure as of what to do and the hammer want budge and the trigger won’t pull. The barrel has no tension and it won’t go up like its supposed to.
ANSWER : This could be a factory safety that the hammer and trigger do not move while in the cocked position. The barrel may be locking down purposely. Look near the spring or in the path of the barrel where it folds back up and look for a release button. What do you see?

We want to assemble our Lifetime World Class Portable Basket ball Hoop but need assembly instructions. FixYa has referred me to dazdi.com where I found the correct document but it doesn’t allow printing. The manual is protected. Please find me a version for assemble Lifetime World Class Basketball Hoop Product 5298 that can be printed at home. Thank you.
ANSWER : Hi,I just checked that assembly instruction manual, it is printable and it is not locked. You can save manual file in computer by clicking save icon (floppy) or let download complete manual in browser window and hit printer icon to get it print. Below image shows how I checked it.Hope these info will help you.Let me know if you have additional question about printing.Thanks.

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Patio heater won’t lite
ANSWER : There is possibly a spider web or wad of web blocking the gas flow between the valve and pilot.Take the line off between the valve and pilot and blow it out with compressed air and it should fix the problem.