e out of my reel is and how I put it back together?
Sport & Outdoor – Others

Experienced athletes share their insights in answering this question:
The shiney pc is the stop so your reel wont go in reverse.look at where the crank go’s through the boby of the reel.there are little teeth on it.the little shiney pc =(reel stop) go’e in that little slot under the crank shaft.

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Bayonet Front Covers Turn front cover counterclockwise until it clicks, then pull front cover toward the first guide on the rod to remove. To remove spinnerhead assembly, hold the handle to prevent rotation and turn the spinnerhead counterclockwise.
You can clean a reel with a degreaser like WD-40, but it leaves a film when it dries that needs to be washed off with soapy water.
Use a toothbrush or small paintbrush to gently scrub and rinse each component of your reel. Don`t submerge the reel itself, but rather rinse with a cloth or by cupping water onto it, so water doesn`t get into the gearing systems and cause damage.
Featuring a tough-yet-sleek design and a durable corrosion-resistant construction, this 808 Salt Fisher reel will look and perform great in even the harshest saltwater environments. The simple push-button mechanics and oversized power knob make this heavy-duty reel a trusted Zebco favorite.
Zebco 33® Spincast Fishing Reel, Pre-Spooled, Anti-Reverse, Reversible.
The reel will not cast line.

Possible Cause: Spool empty of line or insufficient line length. Solution: Fill spool with new line or replace with new wound spool. Possible Cause: Line tangled behind spinnerhead. Solution: Remove front cover and spinnerhead assembly to untangle line.

What causes backlash? Backlash is the result of the spool turning faster than line can leave the spool. This occurs when the lure, as it flies through the air, is met with resistance causing it to slow down. Resistance includes things like the wind or hitting a solid object.
Isopropyl rubbing alcohol will do if a reel needs only minor cleaning, said Dan Thornburn, a Shimano reel guru who does reel maintenance clinics at sports shows. He applies the alcohol with a pump spray bottle. “For heavy cleaning, I use Crystal Simple Green cleaner,” Thornburn said.
After every fishing trip, basic maintenance requirements include cleaning the outside of the real with a damp microfiber cloth and perhaps adding a light layer of protectant and lubrication. WD-40 Multi-Use Product works well to provide routine care with a trusted and easily available product.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Cannot open Shakespeare Synergy Steele 2001s fishing reel
ANSWER : Alright man……i had the same problem. it just takes a little bit of elbow grease, bot it does twist open, it’s just harder than hell to get it to twist off. I took a towel and laid it over the reel, and lightly tapped on it with a hammer to loosen it up a bit.

Read Full Q/A … : Sport & Outdoor – Others

Ladyfish fishing pole by shakespeare
ANSWER : Try switching sides of the handle by holding the bell and reeling then screw it in on the other side of the real by just reeling in.
If that doesn’t work then take all the line out and reel in some new line the opposite way.

Read Full Q/A … : Sport & Outdoor – Others

I have a treadmill Nautilus 516, I mark an error e7 flashing. I already unplugged, lubricated, and clean the speed sensor with alcohol and a clean head cotton. When I jump in at the front it locked out like when you put it in position for move it. When I put start in 4 seconds get the error e7; and when the error still the jump in the front and locked if I put in the back of the walking part do not locked out but still get the e7.
ANSWER : Hi,It stands for a lost signal in the console wire harness. It could be one of the wires has been broken or there is a connection loose. unplug and replug all connections. Then check for continuity in all the wires in the harness. Try to enter the service mode, press Stop Belt, Faster, and Slower
simultaneously. P000 appears in the Select display, indicating that no
key is pressed. To exit the service mode, press and release the same three keys simultaneously or press Power twice to power up into normal mode. Check
the speed sensor to make sure it is within 3-4 inch from the front
roller (magnet). Then check the sensor wire harness to make sure it is
fully seated on the lower control board. If the problem persists, then you need to inspect the machine properly as it could be a faulty console/control board /speed sensor.Let me know,if needed further assistance.Hope i helped you.Thanks for using ‘ Fixya ‘ and have a nice day!!

Read Full Q/A … : Sport & Outdoor – Others

I have a mossberg 510 youth 20 guage i took to the silder for the safety and the piece inside fell im 99% sure i have the peice put back properly but there is a small spring that i dont know what do do with it fell out and i do know where from the slider just freely moves back and forth and think it must be somthing about the spring that is keeping me from being able to get this problem fixed i have been working on this for hours please help
ANSWER : It’s pretty hard to figure this out without seeing the exact pieces sitting in front of someone. What I woud suggest is that you take the gun into a gun shop, and have them help you identify where the spring goes. This is the safest thing to do, when in doubt, otherwise you could jam or otherwise cause some damage.
Perhaps someone will have a Mossman, and know your answer, but if you don’t get one, call on the guys that do it for a living.
Good luck, and hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

I’m was cleaning a zebco 222 {plastic reel} & a metal piece came out & i can’t figure where it goes. It is somewhat a parcial c shape with like a hook at both ends of the c opening & has a tab at the rounded part {on the outside of the c }, can you tell me where this goes.
ANSWER : It goes into a slot at the base of the plastic located near the shaft that goes to the winder. to repair, unmesh the gears and pull the winder shaft out and put C-shaped piece in with tabbed end down into slot located at shaft housing. put gears shaft back through housing and remesh gears. c-shaped piece is for lock after throwing out line and rewinding for line not to run out.

Read Full Q/A … : Sport & Outdoor – Others

Muzzleloader catastrophy!! I need HELP!!
ANSWER : Try pliers

Read Full Q/A … : Sport & Outdoor – Others

How to I fix a spin casting reel?
ANSWER : You should be able to remove the spool by removing the knob on the front of the reel which also is the drag adjustment. With the knob off the spool should pull right off. Hope this helps you

Read Full Q/A … : Sport & Outdoor – Others