Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

If the charging LED is flashing green on your charger, there has been a temperature deviation. The battery might be too cold or too hot to use or charge. This can be solved by doing the following: Let the battery cool down or warm up.
A flashing GREEN LED indicates battery is fully charged, in Maintenance Mode and ready to use.
100% (GREEN) Blinking GREEN LED indicates battery is fully charged in Float Mode and ready to use. Solid GREEN LED indicates battery is fully charged in long term Float Mode. and ready to use. RED A solid RED LED indicates there is an issue with a connection. A blinking RED LED indicates an error.
The indicator light or gauge ( ammeter ) will show that the battery is being charged. The gauge may show a high charging rate at first, but this drops gradually as the battery becomes charged. If it was very flat, charging is likely to take a long time; check periodically with a hydrometer, while continuing the charge.
Generally, this occurs when the charger does not receive a signal from the batteries, in other words there is a break in the connection between the charger and batteries.
A dashboard battery light basically means there`s a battery charging problem. Your car isn`t getting enough voltage from the car battery to operate properly. It needs more “juice!”
A red light comes on to indicate fast charging of the battery. After fast charge is done, the light turns green and the remaining 3 hour charge becomes a trickle charge, optimizing battery performance.
In a lithium-ion battery, overcharging can create unstable conditions inside the battery, increase pressure, and cause thermal runaway. Lithium-ion battery packs are required to have a protection circuit to prevent excessive pressure build-up and cut off the flow of ions when the temperature is too high.
A green indicator means your battery is charging, while a red indicator signals that the battery is low and needs to be plugged into a charger.
Swelling: When a lithium battery fails, another common sign is battery swelling. If your battery looks swollen, you should stop using it immediately. Similar signs include any type of lump or bulge, or leakage from the device. Noise: Failing lithium batteries have also been reported to make hissing or cracking sounds.
The Green LED illuminates to indicate the charger is powered on. The Red LED indicates the battery is charging. The LED will turn Green when the battery is fully charged and on float charge.
The battery level is indicated by the ten LEDs. Each glowing LED indicates 10% of battery voltage level. So, when LED1 through LED5 are glowing, or just LED5 is glowing, it means the battery is around 50% charged.
LED lit symbols

The battery is charging correctly. Charging is complete and the battery is fully charged. The spanner symbol usually means that the battery is being primed or conditioned. There is a delay in charging due to the battery being too hot or too cold. There is a problem with the battery or charger.

The Green LED illuminates to indicate the charger is powered on. The Red LED indicates the battery is charging. The LED will turn Green when the battery is fully charged and on float charge.
As the battery voltage approaches the programmed constant (float) voltage, the charge current begins to drop exponentially. When the charge current drops to a sufficiently low value, the charger stops charging.
Flashing green indicates half charge, flashing red indicates low charge, and solid red indicates battery near empty.
If the charger`s light is red that indicates that the battery is charging. If the charger light stays green that indicates that the battery is fully charged, or that the charger port is not receiving Voltage from the battery pack, or that the battery is overdischarged and cannot be recharged.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

Trying to install a new fluro light, pull out old light to find 3 reds and 3 blacks 1 copper earth. What do I do to connect it up the right way??? When I pulled the old Fluro light out the 3 Reds were joined together with a connector ,two blacks were joined to one end of light wire, the other to the other end of the light wire,earth wire to the light case,the third black wire was connected to the wire from the ballast? Does this all make sense
ANSWER : No, this does not make sense but I have seen strange wiring before. There is power going from the light someplace else. Just connect it back up exactly as the old light was connected. It worked before so it will work again. If it works it is wired correctly. Without being there to check which wire was the hot wire and which was neutral it is impossible for me to say what is what. Make sure you connect the ground wire to the light chassis.

Read Full Q/A … : Sport & Outdoor – Others

Hi, my tiger river spa does not heat. Filters are clean, jets work, no light installed. On ciruit board, green light for “Lim” , red light for heat, no other lights. Just bought house one month ago, no manuals.
Spa is a Bengal. Have noticed a symbol (can’t tell what it is) on the screen then most of screen goes blank with just the power light on. Is there a vacation mode or something like that?
Thanks for your help.
ANSWER : Spa’s are such that so many components can become faulty when left unattended to over a period of time. But most likely what your unit needs is just a regular service to clean up its systems and also ensure there are no leakages in the pipes. Bengal is a wonderful and durable product.The problem could range from low power supply to wires being eaten up by rats and other pests. Also it could be burnt out heaters thereby the inability to produce heat. The indicator on the screen could mean various things but the screen going blank usually would be caused by poor power supply.If you dont have the technical know how refer an expert to check it out and ensure the exact problem of the above mentioned is wrong with it before repairs can be carried out.Hope this solution has been helpful?

Read Full Q/A … : Sport & Outdoor – Others

Trickle charger for storing electric cushman golf cart
ANSWER : Contact manufacturer, and seek there advice

Read Full Q/A … : Sport & Outdoor – Others

Pop-up camper lights all turn on when tow-vehicle lights are on
ANSWER : FIRST, make sure white wire of camper is grounded to the frame of tow-vehicle. Temporarily use a jumper-cable frame-to-frame. Then apply 12volts individually to each of the three circuits to the camper. Assuming a 4-wire flat connector — brown wire is for marker lamps; yellow is left brake/turn; green is right brake/turn

Read Full Q/A … : Sport & Outdoor – Others

No gauges and no lights
ANSWER : Check the battery terminals, it might have been displaced or else there would be some lose connection…………..have a nice day 🙂

Read Full Q/A … : Sport & Outdoor – Others

Had entire spa light replaced 2 mos ago. Now color does not work. Light is “stuck” on white. Doesn’t seem that the color wheel is moving. Service that replaced light only gave me 30 day warranty on light. It was installed 12-13-2010. Any ideas on what to try?
ANSWER : You haven’t said what exact model you have so i can’t be sure but , in the models with rotating screens, the first part that fails is the coloured wheel – the heat deforms it , it bends out of shape and blocks the rotation. You will need to open the system and see if you can rotate the wheel by hand. If you can’t you need a new wheel. If the wheel can be moved by hand you will need to check if the motor gets powered when you try to change colours. If it gets powered but it doesn’t move then the motor is dead. If it doesn’t then the control board is faulty – replace the failed part.

Read Full Q/A … : Sport & Outdoor – Others

I have a wildwood le 25bhbs and the only towing lights working are my signal lights. can’t get running lights or brake lights to work. I saw where it looked like the towing harness may have been pinched. So I repaired that, but, they still do not work. Any ideas? Is there a fuse somewhere I need to check? Do I need to hook the trailer up to my trailer hitch before they will work? Is there a wiring diagram or repair manual somewhere I can get? Any help would be greatly appreciated. Thank you.
ANSWER : There should be an inline fuse, check that first.

Read Full Q/A … : Sport & Outdoor – Others