After turning on my tredclimber TC3000 it just tunrs off by itself after about 10 seconds. The belt (the part where you tred) isn’t working eit…

Pro-form 930i, 2003 model, after not used for 30 days, left plugged-in, will not work. Recalibration efforts with Pro-form didnot work. When unplugged/replugged console shows all 888s for a second, otherwise shows 2 different sets of numbers, 1 all zeros except incline which is 0.5 and the fan works with this, 2 a set of different numbers like 10 and 100, etc. and the fan does not work with these numbers. Thanks for any help you can be.

Hi, I have a commercial grade treadmill, the Technogym Run 600XT Pro that gives the error code E5 (incline fault) that I can’t get rid of. What happened was that after cleaning under the motor cover and turning the treadmill on again this code appeared. What had happened was a wire had come off what looks like a safety switch on the side which I assume trips if the treadmill goes too high. Put the wire back on now I can’t get rid of this error code. Is there a way to reset it from the console please as there isn’t a fault and it was working fine before the wire came off (it didn’t touch anything). Thanks a lot.

I have a Husqvarna LZ6127 zero turn mower, works hard on 50 acre farm, I was mowing last evening and it developed a nasty sounding rattle from the underside, I shut off the deck and noticed sparks from underside along pump belt, I lifted it today and the idler looks ok, I tried to start it while it was lifted and it turned a few times and then just clicked, starter won’t turn the engine over now, should I suspect the clutch?

My reebok i run treadmill was working fine,till my son pulled out the safty key.Now it won”t work at all ! The light is working on the on off switch,but the display is not on nor the belt moving.I have put the key back in,and tryed turning it off for a few minutes.But nothing is happening,there is a small button by the on off switch,not sure if its a reset button, but it is doing nothing, please help. 🙁 x

My swimming pool. I have just had my fifth IC 40 Intellichlor chlorine generator installed in 4 years at a cost of over $900 today. Each one has worked for no more than 8 months. The first three were replaces under three year warranty, the fourth by a factory rep and I bought the fifth today. The first three all failed with Flow Chk PCB error message. The fourth just stopped working on Sunday, no power or lights. A local Pentair warranty person, whom I paid a Service Call, unplugged the unit, opened the small power center cover, showed me the green light indicating that there was power, plugged in a new IC 40 which worked immediately (as did the other four). I asked if I should replace the power center and he said that it’s basically just a transformer and is working fine. We do get occasional power blips that make the clocks on microwaves, etc blink, but I thought that the power center essentially isolates the cell from these. I do have a Florida Power and Light surge protector on the electrical box that brings power into the house. I have now talked to the pool builder, two Pentair warranty repairmen and one factory rep. I am at a loss. They all tell me they have no idea why these units fail after less than a year. This last IC 40 was installed 3/24/2010, version 2.0 and now failed in less than 5 months. Should I replace the power center that the IC 40 plugs into. Any other suggestions. I have been told that this is the best chlorinator. I don’t want to keep replacing units. By the way, each unit had been spotless inside. I keep the water chemicals and salt levels at ideal levels. The units have never worked long enough to get dirty inside. The power center is connected to an Intellitouch control system outside with an indoor control panel. Last time I called Pentair North Carolina and got some smart alec tech person that had no suggestions. Please Help if you can.

Kawasaki bayou 1992, i changed the starter it turns but does not engage, the chain turns the gear moves but moter turns doesnt turn over.. what am i overlooking, ive tried what i know and nothing works..

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?