Sport & Outdoor – Others

How to Identify and Resolve Common Issues ?

We offer a diverse range of insights on identifying and resolving common problems in sports. Our sources encompass academic articles, blog posts, and personal essays shared by seasoned athletes. :

Most 24 volt trolling motors are designed to use two 12 volt batteries that are wired together. You can follow the directions in the video below to make sure you are doing it right. You will want to wire your batteries in series.
The Runtime of a 24V Trolling Motor Battery

Our 24V trolling motor batteries from Abyss Battery feature a general runtime of five to seven hours on a single charge and under favorable conditions. With a 24V 75 Ah or 24V 100Ah setup from Abyss Battery, you can expect an even longer runtime of over eight hours.

Rigging batteries in what`s known as a series adds together the voltage of the battery. So a 24 volt system will require 2 common 12 volt marine batteries in series (12v x 2 = 24v) and a 36 volt system will require 3 (12v x 3 = 36v).
If you were to run a 12v motor off a 24v battery the stall current could then be excessive if it weren`t limited by the controller. Therefore, provided you chose a controller suitable for the motor you use, you can usually run a motor 12v motor from a 24v battery with no effect except that full speed is doubled.
The most straightforward way to force a 12V LED strip to work in a 24V system is to split a 12V LED strip into two identical 12V LED strip segments and connect the copper pads in series, such that the sum of the voltages adds up to the 24V supplied by the power source.
Bow Length

A compound bow`s length is measured from axle to axle, which is where the bow`s limbs connect to the cams. Axle to axle is often abbreviated as ATA. For example, a 35-inch ATA bow measures 35 inches from axle to axle.

Many of our customers can comfortably run their trolling motor and other accessories for a full day fishing trip with our 50Ah models. With our 100Ah models, many customers report 2 or more full days of fishing before needing a recharge.
They typically last around 2-3 years and may require some sort of maintenance.
A single Dakota Lithium 36V 60 Amp Hour (Ah) battery will power a trolling motor for a full day of runtime in river current. On a lake, or low power setting, some anglers report 2+ days of run time. Simplicity.
Going from 24V to 18V is like going from 12 to 9, so it will definitely work at a sufficient speed to be good in most scenarios. If you do not actually have overheating problems with the device you try to cool-down you can certainly use it at 18V.
No. You are applying too much voltage to the motor. This will cause too much current to flow, and in turn, burn out the motor. If it is rated for 12 volts, it should get at the most 10% more or 13.2 volts.
Although it`s easy to assume that a 24-volt power supply can run anything requiring up to 24 volts of electricity, the reality of electrical circuits is not quite so simple. Connecting a single 12-volt light to a 24-volt power supply quickly burns out or dramatically destroys the light.
24V systems are beneficial because you can use smaller diameter wire and reduce amperage by two times. Using smaller diameter wire can reduce wiring costs and decrease the space needed to run wiring. This is especially important where long wire runs are required.
An AC adapter supplying electricity at a higher voltage than required will cause the connected device to run hotter. Sending power at a higher voltage will also shorten the lifespan of the device and may fry its internal circuits.
3) When operating in rough conditions the motor can obviously rise and fall along with your boat, so the longer shaft is great for ensuring your motor stays in the water and maintains stability while you steer.
However, if the shaft is too long, the propeller creates turbulence deep beneath the boat that will spook any nearby fish. And if the shaft is too short, the prop won`t be adequately submerged, which will create noisy chop in the water and also scare away the fish.
For large motors the frame size has three digits, the first two digits stand for the shaft height in one quarter of an inch. The third digit is the bolt mounting holes dimension, the longer the motor body, the longer the distance between mounting bolt holes in the base. Finally, the letter is the type of frame.
My experience with 25″ engines on jackplates on a 20″ transom has been fine. It seems like a benefit to have the engine parts up 5″ higher from the water, and I like jackplates (have them on both boats). If you don`t like jackplates I`d not consider it.
While modern bows can shoot arrows up to 400 yards at speeds exceeding 200 miles per hour, the bow is a short-range hunting tool. Depending on the circumstances, the maximum distance is 30 to 40 yards. At that range, it`s common for an arrow to pass completely through an animal.
You can run a 24 volt trolling motor with a single 24 volt battery. However, if you only have 12 volt batteries available to you, then yes, you`ll need to connect two 12 volt batteries in a series to power the 24 volt trolling motor.
Selecting Battery Quantity

If the motor is 55 lbs. of thrust or less, you will need (1) 12 volt battery. If you have a motor with more than 55 lbs of thrust up to 80 lbs. of thrust, you will need (2) 12 volt batteries for a total of 24 volts.

Selecting Battery Quantity

If the motor is 55 lbs. of thrust or less, you will need (1) 12 volt battery. If you have a motor with more than 55 lbs of thrust up to 80 lbs. of thrust, you will need (2) 12 volt batteries for a total of 24 volts.

80kWh capacity-expansion

The LiFePO4 48V 100Ah battery has a 5X cycle life, which means it can last up to 25 years, making it an excellent long-term investment.

Discover Relevant Questions and Answers for Your Specific Issue

the most relevant questions and answers related to your specific issue

I have the Intex Sand/Pump pool filter Model SF 20110. It’s been running real great for the last 4 months. However recently it has been tripping the internal overloads and I have found the pump motor to be very hot when I put my hand against it. I have tried several different solutions, such as a level ground platform that was clear of any obstructions, made sure that the motor vents under the motor was clear of anything that would prevent air flow. I used a non electrical type of lubricate on the impeller. When I would turn on the pump the rotor would not turn but only would hum very loudly and then slowly begin to turn. I also noticed that the motor’s rotor shaft would not turn to freely due the tightness around the rotor’s shaft. After using the lubricate the shaft would turn a little easier. I used an amp meter on the incoming voltage line and the motor would run at 4.5 amp. And yet it still overheated and tripped the motor overloads. I can only think that the motor is still not getting enough ventilation. I have check and cleared all the incoming lines and found nothing block the pumps input or output lines. Any suggestion?
ANSWER : I just looking into this issue my self. The pump cools itself by a internal fan, which is run by the motor. Well I took the housing cover off to find out all the fan blades have broken off and were setting in the base of the pump. Once you remove the fan blades from covering the air intake, it might be fine. I will find out my self once summer gets here.

Read Full Q/A … : Sport & Outdoor – Others

I have a York Stellar model mid efficiency furnace Model # P?UCD12N07601A, Serial # EXAM3600524 installed in 1992. The HSI was replaced approximately 3 months ago. Over the last two weeks the ventor motor comes on, the HSI lights but does not ignite the gas. The ventor motor runns continously and the HSI continues to turn off and on without gas ignition. Some times by turning the ventor motor off and on (by opening and closing the bottom furnace faces panel door) will give be ignition after the HSI goes through 1-4 cycles. If I can’t get it to work I call my furnace repair guy. The serviceman thought it was the pressure switch and ordered one. Just this last weekend I had no heat and another service guy came in replaced the HSI again and adjusted the pressure switch and said this fix should work. Less than a day later furnace still experiencing the same problem-Ventor motor comes on, HSI comes on but no gas ignition. ventor motor runs continuously and the temperature in the house drops! I’m frustrated and the servicemen don’t seem to know how to fix the problem for good.
ANSWER : Make sure the vent pipes that exhaust the fumes are not blocked in any way and also check the drain line to be sure it is not kinked from the vent motor to the trap. Take the hoses off the vent motor and the pressure switch and make sure all the hoses are clean and free from debris also check the trap on the drain hose and make sure it has water in it if it doesn’t this will creat a negative pressure in the vent motor housing not allowing the vent pressure switch to make.

Read Full Q/A … : Sport & Outdoor – Others

I have a vintage model winchester 24 12 gauge SxS
ANSWER : I spent that past 20min or so runnin through the normal places I normally find Owners manuals for older guns with no luck.The only place i was able to find one is on ebay. Gun Broker.com is also another place they are sellin them.Here is a LINK to the ebay Auction.

Read Full Q/A … : Sport & Outdoor – Others

My daughter has a sweet pea scooter that had been blowing fuses and the motor got hot. Im sure the motor is shot. but my question is can anyone tell me if the motor would be the only thing I need to c
ANSWER : Find out whether it is 6 volts or 12 volts and there should be two wires that feed the motor either cut or splice and attach another set of wires with fuse in the line (simular to jumper cables) raise the back tire so it does not touch the ground and place jump wires to the negative and positive of the battery.If the motor moves in either direction without blowing the fuse the motor is good if not then its bad. Uses the same amperage fuse

Read Full Q/A … : Sport & Outdoor – Others

I have purchased three 750-watt power inverters in the last three weeks. They have all failed to work on the second or third use. The first two were the same brand. I replaced an old one that ran for several years. I am using it to run a 4.7 amp 120-volt vacuum cleaner motor that pumps up my air dock. I have it connected directly with marine cable to one of the boat batteries. The battery outputs about 12.8 volts DC. The fuses don?t blow, just No Output. I am using a three-wire 120-volt extension cord and am, wired neutral, hot and ground to the AC motor vial an on/off switch. The motor works fine when I run house power with an extension cord from the dock next to me. Could I be, just unlucky with new inverters and need to buy a forth one?
ANSWER : The problem may be that the inverter is undersized for the load. Is the 4.7 Amp rating the motor peak draw or the nominal one. What I mean is that it takes many times more power to start start the motor than when the motor is running. Typically it is 3 to 7 times more amps to start the motor than when it is running. It could be that starting the vacumm cleaner is stressing the inverter and it is causing it to fail prematurely. If you can find out the locked rotor current draw of the motor, the that would be the mininum size of the inverter.

Also, the type of inverter will make a difference on how the motor operates. A modified sine wave will make the motor run hotter than a pure sine wave inverter. Hope this helps.

Read Full Q/A … : Sport & Outdoor – Others

My Minn kota bow mount trolling motor turns left & right but the motor won’t run. The motor is good and the foot control is good. What is the problem.
ANSWER : If you know the motor and foot controls aren’t the issue then I would investigate fuses wiring and connectors.

Read Full Q/A … : Sport & Outdoor – Others

I have a 1997 motor guide wireless 24volt Big Water trolling motor. hooked it up to the batteries and put in a new 9volt battery in the foot pedal. the lights come on on top of the motor head and the foot pedal beeps, but the prop doesnt turn or spin (like there is no power to the bottom of the motor) any suggestions to what the problem is or how to fix it? (just bought the motor from a lady who’s husband died. dont have any manuals)
ANSWER : Hello there, as you said the power does not get to the bottom of the motor. The motor could be faulty or just completely bad. First you have to determine that the motor is good until you can determine this it is quite impossible to determine if there can be any fix. Take out the motor and try to power it on its own if it works fine then the problem is not from the motor but most likely the problem is from the motor. Let me know what your findings are. Hoping to hear from you soon.
Thank you for visiting FixYa.

Read Full Q/A … : Sport & Outdoor – Others